blob: e58a69501b3327673648840b43c6d56207ba021b [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2009
* Marvell Semiconductor <www.marvell.com>
* Prafulla Wadaskar <prafulla@marvell.com>
*
* (C) Copyright 2009
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* (C) Copyright 2011-2012
* Holger Brunck, Keymile GmbH Hannover, holger.brunck@keymile.com
* Valentin Longchamp, Keymile AG, valentin.longchamp@keymile.com
*/
/*
* for linking errors see
* http://lists.denx.de/pipermail/u-boot/2009-July/057350.html
*/
#ifndef _CONFIG_KM_KIRKWOOD_H
#define _CONFIG_KM_KIRKWOOD_H
/* KM_KIRKWOOD */
#if defined(CONFIG_KM_KIRKWOOD)
#define CONFIG_HOSTNAME "km_kirkwood"
#define CONFIG_KM_DISABLE_PCIE
/* KM_KIRKWOOD_PCI */
#elif defined(CONFIG_KM_KIRKWOOD_PCI)
#define CONFIG_HOSTNAME "km_kirkwood_pci"
#define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048"
#define CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
/* KM_KIRKWOOD_128M16 */
#elif defined(CONFIG_KM_KIRKWOOD_128M16)
#define CONFIG_HOSTNAME "km_kirkwood_128m16"
#define CONFIG_KM_DISABLE_PCIE
/* KM_NUSA */
#elif defined(CONFIG_KM_NUSA)
#define CONFIG_HOSTNAME "kmnusa"
/* KMCOGE5UN */
#elif defined(CONFIG_KM_COGE5UN)
#define CONFIG_HOSTNAME "kmcoge5un"
#define CONFIG_KM_DISABLE_PCIE
/* KM_SUSE2 */
#elif defined(CONFIG_KM_SUSE2)
#define CONFIG_HOSTNAME "kmsuse2"
#define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048"
#define CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
#else
#error ("Board unsupported")
#endif
/* include common defines/options for all arm based Keymile boards */
#include "km/km_arm.h"
#if defined(CONFIG_KM_PIGGY4_88E6352)
/*
* Some keymile boards like mgcoge5un & nusa1 have their PIGGY4 connected via
* an Marvell 88E6352 simple switch.
* In this case we have to change the default settings for the etherent mac.
* There is NO ethernet phy. The ARM and Switch are conencted directly over
* RGMII in MAC-MAC mode
* In this case 1GBit full duplex and autoneg off
*/
#define PORT_SERIAL_CONTROL_VALUE ( \
MVGBE_FORCE_LINK_PASS | \
MVGBE_DIS_AUTO_NEG_FOR_DUPLX | \
MVGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL | \
MVGBE_ADV_NO_FLOW_CTRL | \
MVGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX | \
MVGBE_FORCE_BP_MODE_NO_JAM | \
(1 << 9) /* Reserved bit has to be 1 */ | \
MVGBE_DO_NOT_FORCE_LINK_FAIL | \
MVGBE_DIS_AUTO_NEG_SPEED_GMII | \
MVGBE_DTE_ADV_0 | \
MVGBE_MIIPHY_MAC_MODE | \
MVGBE_AUTO_NEG_NO_CHANGE | \
MVGBE_MAX_RX_PACKET_1552BYTE | \
MVGBE_CLR_EXT_LOOPBACK | \
MVGBE_SET_FULL_DUPLEX_MODE | \
MVGBE_EN_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX |\
MVGBE_SET_GMII_SPEED_TO_1000 |\
MVGBE_SET_MII_SPEED_TO_100)
#endif
#ifdef CONFIG_KM_PIGGY4_88E6061
/*
* Some keymile boards like mgcoge5un have their PIGGY4 connected via
* an Marvell 88E6061 simple switch.
* In this case we have to change the default settings for the
* ethernet phy connected to the kirkwood.
* In this case 100MB full duplex and autoneg off
*/
#define PORT_SERIAL_CONTROL_VALUE ( \
MVGBE_FORCE_LINK_PASS | \
MVGBE_DIS_AUTO_NEG_FOR_DUPLX | \
MVGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL | \
MVGBE_ADV_NO_FLOW_CTRL | \
MVGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX | \
MVGBE_FORCE_BP_MODE_NO_JAM | \
(1 << 9) /* Reserved bit has to be 1 */ | \
MVGBE_DO_NOT_FORCE_LINK_FAIL | \
MVGBE_DIS_AUTO_NEG_SPEED_GMII | \
MVGBE_DTE_ADV_0 | \
MVGBE_MIIPHY_MAC_MODE | \
MVGBE_AUTO_NEG_NO_CHANGE | \
MVGBE_MAX_RX_PACKET_1552BYTE | \
MVGBE_CLR_EXT_LOOPBACK | \
MVGBE_SET_FULL_DUPLEX_MODE | \
MVGBE_DIS_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX |\
MVGBE_SET_GMII_SPEED_TO_10_100 |\
MVGBE_SET_MII_SPEED_TO_100)
#endif
#ifdef CONFIG_KM_DISABLE_PCIE
#undef CONFIG_KIRKWOOD_PCIE_INIT
#endif
#endif /* _CONFIG_KM_KIRKWOOD */