| /* |
| * (C) Copyright 2003 |
| * Martin Winistoerfer, martinwinistoerfer@gmx.ch. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * File: cmi_mpc5xx.h |
| * |
| * Discription: Config header file for cmi |
| * board using an MPC5xx CPU |
| * |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| */ |
| |
| #define CONFIG_MPC555 1 /* This is an MPC555 CPU */ |
| #define CONFIG_CMI 1 /* Using the customized cmi board */ |
| |
| #define CONFIG_SYS_TEXT_BASE 0x02000000 /* Boot from flash at location 0x00000000 */ |
| |
| /* Serial Console Configuration */ |
| #define CONFIG_5xx_CONS_SCI1 |
| #undef CONFIG_5xx_CONS_SCI2 |
| |
| #define CONFIG_BAUDRATE 57600 |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #undef CONFIG_CMD_NFS |
| |
| #define CONFIG_CMD_MEMORY |
| #define CONFIG_CMD_LOADB |
| #define CONFIG_CMD_REGINFO |
| #define CONFIG_CMD_FLASH |
| #define CONFIG_CMD_LOADS |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_BDI |
| #define CONFIG_CMD_CONSOLE |
| #define CONFIG_CMD_SAVEENV |
| #define CONFIG_CMD_RUN |
| #define CONFIG_CMD_IMI |
| |
| |
| #if 0 |
| #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ |
| #else |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| #endif |
| #define CONFIG_BOOTCOMMAND "go 02034004" /* autoboot command */ |
| |
| #define CONFIG_BOOTARGS "" /* Assuming OS Image in 4 flash sector at offset 4004 */ |
| |
| #define CONFIG_WATCHDOG /* turn on platform specific watchdog */ |
| |
| #define CONFIG_STATUS_LED 1 /* Enable status led */ |
| |
| #define CONFIG_LOADS_ECHO 1 /* Echo on for serial download */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x000fa000 /* 1 MB in SRAM */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 1250000 } |
| |
| |
| /* |
| * Low Level Configuration Settings |
| */ |
| |
| /* |
| * Internal Memory Mapped (This is not the IMMR content) |
| */ |
| #define CONFIG_SYS_IMMR 0x01000000 /* Physical start adress of internal memory map */ |
| |
| /* |
| * Definitions for initial stack pointer and data area |
| */ |
| #define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_IMMR + 0x003f9800) /* Physical start adress of internal MPC555 writable RAM */ |
| #define CONFIG_SYS_INIT_RAM_SIZE (CONFIG_SYS_IMMR + 0x003fffff) /* Physical end adress of internal MPC555 used RAM area */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_RAM_ADDR) - GENERATED_GBL_DATA_SIZE) /* Offset from the beginning of ram */ |
| #define CONFIG_SYS_INIT_SP_ADDR 0x013fa000 /* Physical start adress of inital stack */ |
| |
| /* |
| * Start addresses for the final memory configuration |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 /* Monitor won't change memory map */ |
| #define CONFIG_SYS_FLASH_BASE 0x02000000 /* External flash */ |
| #define PLD_BASE 0x03000000 /* PLD */ |
| #define ANYBUS_BASE 0x03010000 /* Anybus Module */ |
| |
| #define CONFIG_SYS_RESET_ADRESS 0x01000000 /* Adress which causes reset */ |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* CONFIG_SYS_TEXT_BASE is defined in the board config.mk file. */ |
| /* This adress is given to the linker with -Ttext to */ |
| /* locate the text section at this adress. */ |
| #define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ |
| #define CONFIG_SYS_MALLOC_LEN (64 << 10) /* Reserve 128 kB for malloc() */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| *----------------------------------------------------------------------- |
| * |
| */ |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors on one chip */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */ |
| #define CONFIG_SYS_FLASH_PROTECTION 1 /* Physically section protection on */ |
| |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| |
| #ifdef CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_OFFSET 0x00020000 /* Environment starts at this adress */ |
| #define CONFIG_ENV_SIZE 0x00010000 /* Set whole sector as env */ |
| #define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * SYPCR - System Protection Control |
| * SYPCR can only be written once after reset! |
| *----------------------------------------------------------------------- |
| * SW Watchdog freeze |
| */ |
| #if defined(CONFIG_WATCHDOG) |
| #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ |
| SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) |
| #else |
| #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ |
| SYPCR_SWP) |
| #endif /* CONFIG_WATCHDOG */ |
| |
| /*----------------------------------------------------------------------- |
| * TBSCR - Time Base Status and Control |
| *----------------------------------------------------------------------- |
| * Clear Reference Interrupt Status, Timebase freezing enabled |
| */ |
| #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) |
| |
| /*----------------------------------------------------------------------- |
| * PISCR - Periodic Interrupt Status and Control |
| *----------------------------------------------------------------------- |
| * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled |
| */ |
| #define CONFIG_SYS_PISCR (PISCR_PITF) |
| |
| /*----------------------------------------------------------------------- |
| * SCCR - System Clock and reset Control Register |
| *----------------------------------------------------------------------- |
| * Set clock output, timebase and RTC source and divider, |
| * power management and some other internal clocks |
| */ |
| #define SCCR_MASK SCCR_EBDF00 |
| #define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_RTDIV | SCCR_RTSEL | \ |
| SCCR_COM00 | SCCR_DFNL000 | SCCR_DFNH000) |
| |
| /*----------------------------------------------------------------------- |
| * SIUMCR - SIU Module Configuration |
| *----------------------------------------------------------------------- |
| * Data show cycle |
| */ |
| #define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00) /* Disable data show cycle */ |
| |
| /*----------------------------------------------------------------------- |
| * PLPRCR - PLL, Low-Power, and Reset Control Register |
| *----------------------------------------------------------------------- |
| * Set all bits to 40 Mhz |
| * |
| */ |
| #define CONFIG_SYS_OSC_CLK ((uint)4000000) /* Oscillator clock is 4MHz */ |
| #define CONFIG_SYS_PLPRCR (PLPRCR_MF_9 | PLPRCR_DIVF_0) |
| |
| |
| /*----------------------------------------------------------------------- |
| * UMCR - UIMB Module Configuration Register |
| *----------------------------------------------------------------------- |
| * |
| */ |
| #define CONFIG_SYS_UMCR (UMCR_FSPEED) /* IMB clock same as U-bus */ |
| |
| /*----------------------------------------------------------------------- |
| * ICTRL - I-Bus Support Control Register |
| */ |
| #define CONFIG_SYS_ICTRL (ICTRL_ISCT_SER_7) /* Take out of serialized mode */ |
| |
| /*----------------------------------------------------------------------- |
| * USIU - Memory Controller Register |
| *----------------------------------------------------------------------- |
| */ |
| |
| #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_V | BR_BI | BR_PS_16) |
| #define CONFIG_SYS_OR0_PRELIM (OR_ADDR_MK_FF | OR_SCY_3) |
| #define CONFIG_SYS_BR1_PRELIM (ANYBUS_BASE) |
| #define CONFIG_SYS_OR1_PRELIM (OR_ADDR_MK_FFFF | OR_SCY_1 | OR_ETHR) |
| #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_SDRAM_BASE | BR_V | BR_PS_32) |
| #define CONFIG_SYS_OR2_PRELIM (OR_ADDR_MK_FF) |
| #define CONFIG_SYS_BR3_PRELIM (PLD_BASE | BR_V | BR_BI | BR_LBDIR | BR_PS_8) |
| #define CONFIG_SYS_OR3_PRELIM (OR_ADDR_MK_FF | OR_TRLX | OR_BSCY | OR_SCY_8 | \ |
| OR_ACS_10 | OR_ETHR | OR_CSNT) |
| |
| #define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* We don't realign the flash */ |
| |
| /*----------------------------------------------------------------------- |
| * DER - Timer Decrementer |
| *----------------------------------------------------------------------- |
| * Initialise to zero |
| */ |
| #define CONFIG_SYS_DER 0x00000000 |
| |
| #endif /* __CONFIG_H */ |