blob: 9940cf18730e55c7319f19d8520475e722b3e6a8 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+ OR X11
/*
* Copyright 2015 - Maxime Coquelin <mcoquelin.stm32@gmail.com>
*
*/
/dts-v1/;
#include "stm32f746.dtsi"
#include "stm32f746-pinctrl.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "STMicroelectronics STM32746g-EVAL board";
compatible = "st,stm32746g-eval", "st,stm32f746";
chosen {
bootargs = "root=/dev/ram";
stdout-path = "serial0:115200n8";
};
memory@c0000000 {
device_type = "memory";
reg = <0xc0000000 0x2000000>;
};
aliases {
serial0 = &usart1;
};
leds {
compatible = "gpio-leds";
led-green {
gpios = <&gpiof 10 1>;
linux,default-trigger = "heartbeat";
};
led-orange {
gpios = <&stmfx_pinctrl 17 1>;
};
led-red {
gpios = <&gpiob 7 1>;
};
led-blue {
gpios = <&stmfx_pinctrl 19 1>;
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
autorepeat;
button@0 {
label = "Wake up";
linux,code = <KEY_WAKEUP>;
gpios = <&gpioc 13 0>;
};
};
joystick {
compatible = "gpio-keys";
pinctrl-0 = <&joystick_pins>;
pinctrl-names = "default";
button-0 {
label = "JoySel";
linux,code = <KEY_ENTER>;
interrupt-parent = <&stmfx_pinctrl>;
interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
};
button-1 {
label = "JoyDown";
linux,code = <KEY_DOWN>;
interrupt-parent = <&stmfx_pinctrl>;
interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
};
button-2 {
label = "JoyLeft";
linux,code = <KEY_LEFT>;
interrupt-parent = <&stmfx_pinctrl>;
interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
};
button-3 {
label = "JoyRight";
linux,code = <KEY_RIGHT>;
interrupt-parent = <&stmfx_pinctrl>;
interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
};
button-4 {
label = "JoyUp";
linux,code = <KEY_UP>;
interrupt-parent = <&stmfx_pinctrl>;
interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
};
};
usbotg_hs_phy: usb-phy {
#phy-cells = <0>;
compatible = "usb-nop-xceiv";
clocks = <&rcc 0 STM32F7_AHB1_CLOCK(OTGHSULPI)>;
clock-names = "main_clk";
};
mmc_vcard: mmc_vcard {
compatible = "regulator-fixed";
regulator-name = "mmc_vcard";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
};
&clk_hse {
clock-frequency = <25000000>;
};
&crc {
status = "okay";
};
&i2c1 {
pinctrl-0 = <&i2c1_pins_b>;
pinctrl-names = "default";
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
stmfx: stmfx@42 {
compatible = "st,stmfx-0300";
reg = <0x42>;
interrupts = <8 IRQ_TYPE_EDGE_RISING>;
interrupt-parent = <&gpioi>;
stmfx_pinctrl: pinctrl {
compatible = "st,stmfx-0300-pinctrl";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-ranges = <&stmfx_pinctrl 0 0 24>;
joystick_pins: joystick {
pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
drive-push-pull;
bias-pull-up;
};
};
};
};
&rtc {
status = "okay";
};
&sdio1 {
status = "okay";
vmmc-supply = <&mmc_vcard>;
broken-cd;
pinctrl-names = "default", "opendrain";
pinctrl-0 = <&sdio_pins_a>;
pinctrl-1 = <&sdio_pins_od_a>;
bus-width = <4>;
};
&usart1 {
pinctrl-0 = <&usart1_pins_a>;
pinctrl-names = "default";
status = "okay";
};
&usbotg_hs {
dr_mode = "otg";
phys = <&usbotg_hs_phy>;
phy-names = "usb2-phy";
pinctrl-0 = <&usbotg_hs_pins_a>;
pinctrl-names = "default";
status = "okay";
};