board/ti/ks2_evm/README - platform/external/u-boot - Gitiles

 U-Boot port for Texas Instruments Keystone II EVM boards
 ========================================================

 Author: Murali Karicheri <m-karicheri2@ti.com>

 This README has information on the U-Boot port for K2HK, K2E, and K2L EVM boards.
 Documentation for this board can be found at
 http://www.advantech.com/Support/TI-EVM/EVMK2HX_sd.aspx
 https://www.einfochips.com/index.php/partnerships/texas-instruments/k2e-evm.html
 https://www.einfochips.com/index.php/partnerships/texas-instruments/k2l-evm.html

 The K2HK board is based on Texas Instruments Keystone2 family of SoCs: K2H, K2K.
 More details on these SoCs are available at company websites
  K2K: http://www.ti.com/product/tci6638k2k
  K2H: http://www.ti.com/product/tci6638k2h

 The K2E SoC details are available at
  http://www.ti.com/lit/ds/symlink/66ak2e05.pdf

 The K2L SoC details are available at
  http://www.ti.com/lit/ds/symlink/tci6630k2l.pdf

 The K2G SoC details are available at
  http://www.ti.com/lit/ds/symlink/66ak2g02.pdf

 Board configuration:
 ====================

 Some of the peripherals that are configured by U-Boot
 +------+-------+-------+-----------+-----------+-------+-------+----+
 |      |DDR3   |NAND   |MSM SRAM   |ETH ports  |UART   |I2C    |SPI |
 +------+-------+-------+-----------+-----------+-------+-------+----+
 |K2HK  |2      |512MB  |6MB	   |4(2)       |2      |3      |3   |
 |K2E   |4      |512MB  |2MB	   |8(2)       |2      |3      |3   |
 |K2L   |2      |512MB  |2MB	   |4(2)       |4      |3      |3   |
 |K2G   |2      |256MB  |1MB	   |1          |1      |1      |1   |
 +------+-------+-------+-----------+-----------+-------+-------+----+

 There are only 2 eth port installed on the boards.

 There are separate PLLs to drive clocks to Tetris ARM and Peripherals.
 To bring up SMP Linux on this board, there is a boot monitor
 code that will be installed in MSMC SRAM. There is command available
 to install this image from U-Boot.

 The port related files can be found at following folders
  keystone2 SoC related files: arch/arm/cpu/armv7/keystone/
  EVMs board files: board/ti/k2s_evm/

 Board configuration files:
 include/configs/k2hk_evm.h
 include/configs/k2e_evm.h
 include/configs/k2l_evm.h
 include/configs/k2g_evm.h

 As U-Boot is migrating to Kconfig there is also board defconfig files
 configs/k2e_evm_defconfig
 configs/k2hk_evm_defconfig
 configs/k2l_evm_defconfig
 configs/k2g_evm_defconfig

 Supported boot modes:
  - SPI NOR boot
  - AEMIF NAND boot (K2E, K2L and K2HK)
  - UART boot
  - MMC boot (Only on K2G)

 Supported image formats:
  - u-boot.bin: for loading and running u-boot.bin through
 		Texas Instruments code composure studio (CCS) and for UART boot.
  - u-boot-spi.gph: gpimage for programming SPI NOR flash for SPI NOR boot
  - MLO: gpimage for programming NAND flash for NAND boot, MMC boot.

 Build instructions:
 ===================
 Examples for k2hk, for k2e, k2l and k2g just replace k2hk prefix accordingly.
 Don't forget to add CROSS_COMPILE.

 To build u-boot.bin, u-boot-spi.gph, MLO:
   >make k2hk_evm_defconfig
   >make

 Load and Run U-Boot on keystone EVMs using CCS
 =========================================

 Need Code Composer Studio (CCS) installed on a PC to load and run u-boot.bin
 on EVM. See instructions at below link for installing CCS on a Windows PC.
 http://processors.wiki.ti.com/index.php/MCSDK_UG_Chapter_Getting_Started#
 Installing_Code_Composer_Studio
 Use u-boot.bin from the build folder for loading and running U-Boot binary
 on EVM. Follow instructions at
 K2HK http://processors.wiki.ti.com/index.php/EVMK2H_Hardware_Setup
 K2E  http://processors.wiki.ti.com/index.php/EVMK2E_Hardware_Setup
 K2L  http://processors.wiki.ti.com/index.php/TCIEVMK2L_Hardware_Setup
 K2G  http://processors.wiki.ti.com/index.php/66AK2G02_GP_EVM_Hardware_Setup

 to configure SW1 dip switch to use "No Boot/JTAG DSP Little Endian Boot Mode"
 and Power ON the EVM.  Follow instructions to connect serial port of EVM to
 PC and start TeraTerm or Hyper Terminal.

 Start CCS on a Windows machine and Launch Target
 configuration as instructed at http://processors.wiki.ti.com/index.php/
 MCSDK_UG_Chapter_Exploring#Loading_and_Running_U-Boot_on_EVM_through_CCS.
 The instructions provided in the above link uses a script for
 loading the U-Boot binary on the target EVM. Instead do the following:-

 1. Right click to "Texas Instruments XDS2xx USB Emulator_0/CortexA15_1 core (D
    is connected: Unknown)" at the debug window (This is created once Target
    configuration is launched) and select "Connect Target".
 2. Once target connect is successful, choose Tools->Load Memory option from the
    top level menu. At the Load Memory window, choose the file u-boot.bin
    through "Browse" button and click "next >" button. In the next window, enter
    Start address as 0xc000000, choose Type-size "32 bits" and click "Finish"
    button.
 3. Click View -> Registers from the top level menu to view registers window.
 4. From Registers, window expand "Core Registers" to view PC. Edit PC value
    to be 0xc000000. From the "Run" top level menu, select "Free Run"
 5. The U-Boot prompt is shown at the Tera Term/ Hyper terminal console as
    below and type any key to stop autoboot as instructed :=

 U-Boot 2014.04-rc1-00201-gc215b5a (Mar 21 2014 - 12:47:59)

 I2C:   ready
 Detected SO-DIMM [SQR-SD3T-2G1333SED]
 DRAM:  1.1 GiB
 NAND:  512 MiB
 Net:   K2HK_EMAC
 Warning: K2HK_EMAC using MAC address from net device
 , K2HK_EMAC1, K2HK_EMAC2, K2HK_EMAC3
 Hit any key to stop autoboot:  0

 SPI NOR Flash programming instructions
 ======================================
 U-Boot image can be flashed to first 512KB of the NOR flash using following
 instructions:

 1. Start CCS and run U-Boot as described above.
 2. Suspend Target. Select Run -> Suspend from top level menu
    CortexA15_1 (Free Running)"
 3. Load u-boot-spi.gph binary from build folder on to DDR address 0x87000000
    through CCS as described in step 2 of "Load and Run U-Boot on K2HK/K2E/K2L
    EVM using CCS", but using address 0x87000000.
 4. Free Run the target as described earlier (step 4) to get U-Boot prompt
 5. At the U-Boot console type following to setup U-Boot environment variables.
    setenv addr_uboot 0x87000000
    setenv filesize <size in hex of u-boot-spi.gph rounded to hex 0x10000>
    run burn_uboot_spi
    Once U-Boot prompt is available, Power OFF the EVM. Set the SW1 dip switch
    to "SPI Little Endian Boot mode" as per instruction at
    http://processors.wiki.ti.com/index.php/*_Hardware_Setup.
 6. Power ON the EVM. The EVM now boots with U-Boot image on the NOR flash.

 AEMIF NAND Flash programming instructions
 ======================================
 U-Boot image can be flashed to first 1024KB of the NAND flash using following
 instructions:

 1. Start CCS and run U-Boot as described above.
 2. Suspend Target. Select Run -> Suspend from top level menu
    CortexA15_1 (Free Running)"
 3. Load MLO binary from build folder on to DDR address 0x87000000
    through CCS as described in step 2 of "Load and Run U-Boot on K2HK EVM
    using CCS", but using address 0x87000000.
 4. Free Run the target as described earlier (step 4) to get U-Boot prompt
 5. At the U-Boot console type following to setup U-Boot environment variables.
    setenv filesize <size in hex of MLO rounded to hex 0x10000>
    run burn_uboot_nand
    Once U-Boot prompt is available, Power OFF the EVM. Set the SW1 dip switch
    to "ARM NAND Boot mode" as per instruction at
    http://processors.wiki.ti.com/index.php/*_Hardware_Setup.
 6. Power ON the EVM. The EVM now boots with U-Boot image on the NAND flash.

 Load and Run U-Boot on keystone EVMs using UART download
 ========================================================

 Open BMC and regular UART terminals.

 1. On the regular UART port start xmodem transfer of the u-boot.bin
 2. Using BMC terminal set the ARM-UART bootmode and reboot the EVM
    BMC> bootmode #4
    MBC> reboot
 3. When xmodem is complete you should see the U-Boot starts on the UART port

 Load and Run U-Boot on K2G EVMs using MMC
 ========================================================

 Open BMC and regular UART terminals.

 1. Set the SW3 dip switch to "ARM MMC Boot mode" as per instruction at
    http://processors.wiki.ti.com/index.php/66AK2G02_GP_EVM_Hardware_Setup
 2. Create SD card partitions as per steps given in Hardware Setup Guide.
 3. Copy MLO to Boot Partition.
 4. Insert SD card and Power on the EVM.
    The EVM now boots with U-Boot image from SD card.
	U-Boot port for Texas Instruments Keystone II EVM boards
	========================================================

	Author: Murali Karicheri <m-karicheri2@ti.com>

	This README has information on the U-Boot port for K2HK, K2E, and K2L EVM boards.
	Documentation for this board can be found at
	http://www.advantech.com/Support/TI-EVM/EVMK2HX_sd.aspx
	https://www.einfochips.com/index.php/partnerships/texas-instruments/k2e-evm.html
	https://www.einfochips.com/index.php/partnerships/texas-instruments/k2l-evm.html

	The K2HK board is based on Texas Instruments Keystone2 family of SoCs: K2H, K2K.
	More details on these SoCs are available at company websites
	K2K: http://www.ti.com/product/tci6638k2k
	K2H: http://www.ti.com/product/tci6638k2h

	The K2E SoC details are available at
	http://www.ti.com/lit/ds/symlink/66ak2e05.pdf

	The K2L SoC details are available at
	http://www.ti.com/lit/ds/symlink/tci6630k2l.pdf

	The K2G SoC details are available at
	http://www.ti.com/lit/ds/symlink/66ak2g02.pdf

	Board configuration:
	====================

	Some of the peripherals that are configured by U-Boot
	+------+-------+-------+-----------+-----------+-------+-------+----+
	\| \|DDR3 \|NAND \|MSM SRAM \|ETH ports \|UART \|I2C \|SPI \|
	+------+-------+-------+-----------+-----------+-------+-------+----+
	\|K2HK \|2 \|512MB \|6MB \|4(2) \|2 \|3 \|3 \|
	\|K2E \|4 \|512MB \|2MB \|8(2) \|2 \|3 \|3 \|
	\|K2L \|2 \|512MB \|2MB \|4(2) \|4 \|3 \|3 \|
	\|K2G \|2 \|256MB \|1MB \|1 \|1 \|1 \|1 \|
	+------+-------+-------+-----------+-----------+-------+-------+----+

	There are only 2 eth port installed on the boards.

	There are separate PLLs to drive clocks to Tetris ARM and Peripherals.
	To bring up SMP Linux on this board, there is a boot monitor
	code that will be installed in MSMC SRAM. There is command available
	to install this image from U-Boot.

	The port related files can be found at following folders
	keystone2 SoC related files: arch/arm/cpu/armv7/keystone/
	EVMs board files: board/ti/k2s_evm/

	Board configuration files:
	include/configs/k2hk_evm.h
	include/configs/k2e_evm.h
	include/configs/k2l_evm.h
	include/configs/k2g_evm.h

	As U-Boot is migrating to Kconfig there is also board defconfig files
	configs/k2e_evm_defconfig
	configs/k2hk_evm_defconfig
	configs/k2l_evm_defconfig
	configs/k2g_evm_defconfig

	Supported boot modes:
	- SPI NOR boot
	- AEMIF NAND boot (K2E, K2L and K2HK)
	- UART boot
	- MMC boot (Only on K2G)

	Supported image formats:
	- u-boot.bin: for loading and running u-boot.bin through
	Texas Instruments code composure studio (CCS) and for UART boot.
	- u-boot-spi.gph: gpimage for programming SPI NOR flash for SPI NOR boot
	- MLO: gpimage for programming NAND flash for NAND boot, MMC boot.

	Build instructions:
	===================
	Examples for k2hk, for k2e, k2l and k2g just replace k2hk prefix accordingly.
	Don't forget to add CROSS_COMPILE.

	To build u-boot.bin, u-boot-spi.gph, MLO:
	>make k2hk_evm_defconfig
	>make

	Load and Run U-Boot on keystone EVMs using CCS
	=========================================

	Need Code Composer Studio (CCS) installed on a PC to load and run u-boot.bin
	on EVM. See instructions at below link for installing CCS on a Windows PC.
	http://processors.wiki.ti.com/index.php/MCSDK_UG_Chapter_Getting_Started#
	Installing_Code_Composer_Studio
	Use u-boot.bin from the build folder for loading and running U-Boot binary
	on EVM. Follow instructions at
	K2HK http://processors.wiki.ti.com/index.php/EVMK2H_Hardware_Setup
	K2E http://processors.wiki.ti.com/index.php/EVMK2E_Hardware_Setup
	K2L http://processors.wiki.ti.com/index.php/TCIEVMK2L_Hardware_Setup
	K2G http://processors.wiki.ti.com/index.php/66AK2G02_GP_EVM_Hardware_Setup

	to configure SW1 dip switch to use "No Boot/JTAG DSP Little Endian Boot Mode"
	and Power ON the EVM. Follow instructions to connect serial port of EVM to
	PC and start TeraTerm or Hyper Terminal.

	Start CCS on a Windows machine and Launch Target
	configuration as instructed at http://processors.wiki.ti.com/index.php/
	MCSDK_UG_Chapter_Exploring#Loading_and_Running_U-Boot_on_EVM_through_CCS.
	The instructions provided in the above link uses a script for
	loading the U-Boot binary on the target EVM. Instead do the following:-

	1. Right click to "Texas Instruments XDS2xx USB Emulator_0/CortexA15_1 core (D
	is connected: Unknown)" at the debug window (This is created once Target
	configuration is launched) and select "Connect Target".
	2. Once target connect is successful, choose Tools->Load Memory option from the
	top level menu. At the Load Memory window, choose the file u-boot.bin
	through "Browse" button and click "next >" button. In the next window, enter
	Start address as 0xc000000, choose Type-size "32 bits" and click "Finish"
	button.
	3. Click View -> Registers from the top level menu to view registers window.
	4. From Registers, window expand "Core Registers" to view PC. Edit PC value
	to be 0xc000000. From the "Run" top level menu, select "Free Run"
	5. The U-Boot prompt is shown at the Tera Term/ Hyper terminal console as
	below and type any key to stop autoboot as instructed :=

	U-Boot 2014.04-rc1-00201-gc215b5a (Mar 21 2014 - 12:47:59)

	I2C: ready
	Detected SO-DIMM [SQR-SD3T-2G1333SED]
	DRAM: 1.1 GiB
	NAND: 512 MiB
	Net: K2HK_EMAC
	Warning: K2HK_EMAC using MAC address from net device
	, K2HK_EMAC1, K2HK_EMAC2, K2HK_EMAC3
	Hit any key to stop autoboot: 0

	SPI NOR Flash programming instructions
	======================================
	U-Boot image can be flashed to first 512KB of the NOR flash using following
	instructions:

	1. Start CCS and run U-Boot as described above.
	2. Suspend Target. Select Run -> Suspend from top level menu
	CortexA15_1 (Free Running)"
	3. Load u-boot-spi.gph binary from build folder on to DDR address 0x87000000
	through CCS as described in step 2 of "Load and Run U-Boot on K2HK/K2E/K2L
	EVM using CCS", but using address 0x87000000.
	4. Free Run the target as described earlier (step 4) to get U-Boot prompt
	5. At the U-Boot console type following to setup U-Boot environment variables.
	setenv addr_uboot 0x87000000
	setenv filesize <size in hex of u-boot-spi.gph rounded to hex 0x10000>
	run burn_uboot_spi
	Once U-Boot prompt is available, Power OFF the EVM. Set the SW1 dip switch
	to "SPI Little Endian Boot mode" as per instruction at
	http://processors.wiki.ti.com/index.php/*_Hardware_Setup.
	6. Power ON the EVM. The EVM now boots with U-Boot image on the NOR flash.

	AEMIF NAND Flash programming instructions
	======================================
	U-Boot image can be flashed to first 1024KB of the NAND flash using following
	instructions:

	1. Start CCS and run U-Boot as described above.
	2. Suspend Target. Select Run -> Suspend from top level menu
	CortexA15_1 (Free Running)"
	3. Load MLO binary from build folder on to DDR address 0x87000000
	through CCS as described in step 2 of "Load and Run U-Boot on K2HK EVM
	using CCS", but using address 0x87000000.
	4. Free Run the target as described earlier (step 4) to get U-Boot prompt
	5. At the U-Boot console type following to setup U-Boot environment variables.
	setenv filesize <size in hex of MLO rounded to hex 0x10000>
	run burn_uboot_nand
	Once U-Boot prompt is available, Power OFF the EVM. Set the SW1 dip switch
	to "ARM NAND Boot mode" as per instruction at
	http://processors.wiki.ti.com/index.php/*_Hardware_Setup.
	6. Power ON the EVM. The EVM now boots with U-Boot image on the NAND flash.

	Load and Run U-Boot on keystone EVMs using UART download
	========================================================

	Open BMC and regular UART terminals.

	1. On the regular UART port start xmodem transfer of the u-boot.bin
	2. Using BMC terminal set the ARM-UART bootmode and reboot the EVM
	BMC> bootmode #4
	MBC> reboot
	3. When xmodem is complete you should see the U-Boot starts on the UART port

	Load and Run U-Boot on K2G EVMs using MMC
	========================================================

	Open BMC and regular UART terminals.

	1. Set the SW3 dip switch to "ARM MMC Boot mode" as per instruction at
	http://processors.wiki.ti.com/index.php/66AK2G02_GP_EVM_Hardware_Setup
	2. Create SD card partitions as per steps given in Hardware Setup Guide.
	3. Copy MLO to Boot Partition.
	4. Insert SD card and Power on the EVM.
	The EVM now boots with U-Boot image from SD card.