doc/kwboot.1 - platform/external/u-boot - Gitiles

 .TH KWBOOT 1 "2022-03-02"

 .SH NAME
 kwboot \- Boot Marvell Kirkwood (and others 32-bit) SoCs over a serial link.
 .SH SYNOPSIS
 .B kwboot
 .RB [ "-b \fIimage\fP" ]
 .RB [ "-t" ]
 .RB [ "-B \fIbaudrate\fP" ]
 .RB \fITTY\fP
 .SH "DESCRIPTION"

 The \fBkwboot\fP program boots boards based on Marvell's 32-bit
 platforms including Kirkwood, Dove, Avanta, A370, AXP, A375, A38x
 and A39x over their integrated UART. Boot image files will typically
 contain a second stage boot loader, such as U-Boot. The image file
 must conform to Marvell's BootROM firmware image format
 (\fIkwbimage v0\fP or \fIv1\fP), created using a tool such as
 \fBmkimage\fP.

 Following power-up or a system reset, system BootROM code polls the
 UART for a brief period of time, sensing a handshake message which
 initiates an image upload. This program sends this boot message until
 it receives a positive acknowledgement. The image is transferred using
 Xmodem.

 Additionally, this program implements a minimal terminal mode, which
 can be used either standalone, or entered immediately following boot
 image transfer completion. This is often useful to catch early boot
 messages, or to manually interrupt a default boot procedure performed
 by the second-stage loader.

 .SH "OPTIONS"

 .TP
 .BI "\-b \fIimage\fP"
 Handshake; then upload file \fIimage\fP over \fITTY\fP.

 Note that for the encapsulated boot code to be executed, \fIimage\fP
 must be of type "UART boot" (0x69). The \fBkwboot\fP program changes
 this type automatically, unless the \fIimage\fP is signed, in which
 case it cannot be changed.

 This mode writes handshake status and upload progress indication to
 stdout. It is possible that \fIimage\fP contains an optional binary
 code in it's header which may also print some output via UART (for
 example U-Boot SPL does this). In such a case, this output is also
 written to stdout after the header is sent.

 .TP
 .B "\-b"
 Do only handshake on \fITTY\fP without uploading any file. File upload
 could be done later via option \fB\-D\fP or via any other Xmodem
 application, like \fBsx\fP(1).

 .TP
 .B "\-d"
 Do special handshake on \fITTY\fP for console debug mode.

 This will instruct BootROM to enter builtin simple console debug mode.
 Should be combined with option \fB\-t\fP.

 To get a BootROM help, type this command followed by ENTER key:

 .RS 1.2i
 .TP
 .B ?
 .RE
 .IP

 Armada 38x BootROM has a bug which cause that BootROM's standard output
 is turned off on UART when default boot source location contains valid boot image. Nevertheless
 BootROM's standard input and BootROM's terminal echo are active and working
 fine. To workaround this BootROM bug with standard output, it is possible
 to manually overwrite BootROM variables stored in SRAM which BootROM use
 for checking if standard output is enabled or not. To enable BootROM
 standard output on UART, type this command followed by ENTER key:

 .RS 1.2i
 .TP
 .B w 0x40034100 1
 .RE

 .TP
 .BI "\-D" " image"
 Upload file \fIimage\fP over \fITTY\fP without initial handshake.

 This method is used primary on Dove platforms, where BootROM does
 not support initial handshake for entering UART upload mode and
 strapping pins (exported via e.g. buttons) are used instead.

 .TP
 .BI "\-p"
 Obsolete. Does nothing.

 In the past, when this option was used, the program patched the header
 in the image prior upload, to "UART boot" type. This is now done by
 default.

 .TP
 .B "\-q"
 Obsolete. Does nothing.

 It is unknown whether it did something in the past.

 .TP
 .BI "\-s" " response-timeout"
 Specify custom response timeout when doing handshake. Default value is 50 ms.
 It is the timeout between sending two consecutive handshake patterns, meaning
 how long to wait for response from BootROM. Affects only option \fB\-b\fP with
 image file and option \fB\-d\fP.

 Option \fB-a\fP specify response timeout suitable for Armada XP BootROM and
 currently it is 1000 ms.

 Some testing showed that specifying 24 ms as response timeout make handshake
 with Armada 385 BootROM more stable.

 .TP
 .BI "\-t"
 Run a terminal program, connecting standard input and output to
 .RB \fITTY\fP.

 If used in combination with \fB\-b\fP, \fB\-D\fP or \fB\-d\fP option,
 terminal mode is entered immediately following a successful image upload
 or successful handshake (if not doing image upload).

 If standard I/O streams connect to a console, this mode will terminate
 after receiving \fBctrl-\e\fP followed by \fBc\fP from console input.

 .TP
 .BI "\-B \fIbaudrate\fP"
 If used in combination with \fB-b\fP, inject into the image header
 code that changes baud rate to \fIbaudrate\fP after uploading image
 header, and code that changes the baud rate back to the default
 (115200 Bd) before executing payload, and also adjust the baud rate
 on \fITTY\fP correspondingly. This can make the upload significantly
 faster.

 If used in combination with \fB-t\fP, adjust the baud rate to
 \fIbaudrate\fP on \fITTY\fP before starting terminal.

 If both \fB-b\fP and \fB-t\fP are used, the baud rate is changed
 back to 115200 after the upload.

 Tested values for \fIbaudrate\fP for Armada 38x include: 115200,
 230400, 460800, 500000, 576000, 921600, 1000000, 1152000, 1500000,
 2000000, 2500000, 3125000, 4000000 and 5200000.

 .SH "EXAMPLES"

 Instruct BootROM to enter boot Xmodem boot mode, send \fIu-boot-with-spl.kwb\fP
 kwbimage file via Xmodem on \fI/dev/ttyUSB0\fP at 115200 Bd and run terminal
 program:
 .IP
 .B kwboot -b u-boot-with-spl.kwb -t /dev/ttyUSB0

 .PP
 Instruct BootROM to enter boot Xmodem boot mode, send header of
 \fIu-boot-with-spl.kwb\fP kwbimage file via Xmodem at 115200 Bd, then instruct
 BootROM to change baudrate to 5200000 Bd, send data part of the kwbimage
 file via Xmodem at high speed, then change baudrate back to 115200 Bd,
 and finally run terminal program:
 .IP
 .B kwboot -b u-boot-with-spl.kwb -B 5200000 -t /dev/ttyUSB0

 .PP
 Only send \fIu-boot-with-spl.kwb\fP kwbimage file via Xmodem on \fI/dev/ttyUSB0\fP
 at 115200 Bd:
 .IP
 .B kwboot -D u-boot-with-spl.kwb /dev/ttyUSB0

 .PP
 Instruct BootROM to enter console debug mode and run terminal program on
 \fI/dev/ttyUSB0\fP at 115200 Bd:
 .IP
 .B kwboot -d -t /dev/ttyUSB0

 .PP
 Only run terminal program on \fI/dev/ttyUSB0\fP at 115200 Bd:
 .IP
 .B kwboot -t /dev/ttyUSB0

 .SH "SEE ALSO"
 .PP
 \fBmkimage\fP(1), \fBsx\fP(1)

 .SH "AUTHORS"

 Daniel Stodden <daniel.stodden@gmail.com>
 .br
 Luka Perkov <luka@openwrt.org>
 .br
 David Purdy <david.c.purdy@gmail.com>
 .br
 Pali Rohár <pali@kernel.org>
 .br
 Marek Behún <kabel@kernel.org>
	.TH KWBOOT 1 "2022-03-02"

	.SH NAME
	kwboot \- Boot Marvell Kirkwood (and others 32-bit) SoCs over a serial link.
	.SH SYNOPSIS
	.B kwboot
	.RB [ "-b \fIimage\fP" ]
	.RB [ "-t" ]
	.RB [ "-B \fIbaudrate\fP" ]
	.RB \fITTY\fP
	.SH "DESCRIPTION"

	The \fBkwboot\fP program boots boards based on Marvell's 32-bit
	platforms including Kirkwood, Dove, Avanta, A370, AXP, A375, A38x
	and A39x over their integrated UART. Boot image files will typically
	contain a second stage boot loader, such as U-Boot. The image file
	must conform to Marvell's BootROM firmware image format
	(\fIkwbimage v0\fP or \fIv1\fP), created using a tool such as
	\fBmkimage\fP.

	Following power-up or a system reset, system BootROM code polls the
	UART for a brief period of time, sensing a handshake message which
	initiates an image upload. This program sends this boot message until
	it receives a positive acknowledgement. The image is transferred using
	Xmodem.

	Additionally, this program implements a minimal terminal mode, which
	can be used either standalone, or entered immediately following boot
	image transfer completion. This is often useful to catch early boot
	messages, or to manually interrupt a default boot procedure performed
	by the second-stage loader.

	.SH "OPTIONS"

	.TP
	.BI "\-b \fIimage\fP"
	Handshake; then upload file \fIimage\fP over \fITTY\fP.

	Note that for the encapsulated boot code to be executed, \fIimage\fP
	must be of type "UART boot" (0x69). The \fBkwboot\fP program changes
	this type automatically, unless the \fIimage\fP is signed, in which
	case it cannot be changed.

	This mode writes handshake status and upload progress indication to
	stdout. It is possible that \fIimage\fP contains an optional binary
	code in it's header which may also print some output via UART (for
	example U-Boot SPL does this). In such a case, this output is also
	written to stdout after the header is sent.

	.TP
	.B "\-b"
	Do only handshake on \fITTY\fP without uploading any file. File upload
	could be done later via option \fB\-D\fP or via any other Xmodem
	application, like \fBsx\fP(1).

	.TP
	.B "\-d"
	Do special handshake on \fITTY\fP for console debug mode.

	This will instruct BootROM to enter builtin simple console debug mode.
	Should be combined with option \fB\-t\fP.

	To get a BootROM help, type this command followed by ENTER key:

	.RS 1.2i
	.TP
	.B ?
	.RE
	.IP

	Armada 38x BootROM has a bug which cause that BootROM's standard output
	is turned off on UART when default boot source location contains valid boot image. Nevertheless
	BootROM's standard input and BootROM's terminal echo are active and working
	fine. To workaround this BootROM bug with standard output, it is possible
	to manually overwrite BootROM variables stored in SRAM which BootROM use
	for checking if standard output is enabled or not. To enable BootROM
	standard output on UART, type this command followed by ENTER key:

	.RS 1.2i
	.TP
	.B w 0x40034100 1
	.RE

	.TP
	.BI "\-D" " image"
	Upload file \fIimage\fP over \fITTY\fP without initial handshake.

	This method is used primary on Dove platforms, where BootROM does
	not support initial handshake for entering UART upload mode and
	strapping pins (exported via e.g. buttons) are used instead.

	.TP
	.BI "\-p"
	Obsolete. Does nothing.

	In the past, when this option was used, the program patched the header
	in the image prior upload, to "UART boot" type. This is now done by
	default.

	.TP
	.B "\-q"
	Obsolete. Does nothing.

	It is unknown whether it did something in the past.

	.TP
	.BI "\-s" " response-timeout"
	Specify custom response timeout when doing handshake. Default value is 50 ms.
	It is the timeout between sending two consecutive handshake patterns, meaning
	how long to wait for response from BootROM. Affects only option \fB\-b\fP with
	image file and option \fB\-d\fP.

	Option \fB-a\fP specify response timeout suitable for Armada XP BootROM and
	currently it is 1000 ms.

	Some testing showed that specifying 24 ms as response timeout make handshake
	with Armada 385 BootROM more stable.

	.TP
	.BI "\-t"
	Run a terminal program, connecting standard input and output to
	.RB \fITTY\fP.

	If used in combination with \fB\-b\fP, \fB\-D\fP or \fB\-d\fP option,
	terminal mode is entered immediately following a successful image upload
	or successful handshake (if not doing image upload).

	If standard I/O streams connect to a console, this mode will terminate
	after receiving \fBctrl-\e\fP followed by \fBc\fP from console input.

	.TP
	.BI "\-B \fIbaudrate\fP"
	If used in combination with \fB-b\fP, inject into the image header
	code that changes baud rate to \fIbaudrate\fP after uploading image
	header, and code that changes the baud rate back to the default
	(115200 Bd) before executing payload, and also adjust the baud rate
	on \fITTY\fP correspondingly. This can make the upload significantly
	faster.

	If used in combination with \fB-t\fP, adjust the baud rate to
	\fIbaudrate\fP on \fITTY\fP before starting terminal.

	If both \fB-b\fP and \fB-t\fP are used, the baud rate is changed
	back to 115200 after the upload.

	Tested values for \fIbaudrate\fP for Armada 38x include: 115200,
	230400, 460800, 500000, 576000, 921600, 1000000, 1152000, 1500000,
	2000000, 2500000, 3125000, 4000000 and 5200000.

	.SH "EXAMPLES"

	Instruct BootROM to enter boot Xmodem boot mode, send \fIu-boot-with-spl.kwb\fP
	kwbimage file via Xmodem on \fI/dev/ttyUSB0\fP at 115200 Bd and run terminal
	program:
	.IP
	.B kwboot -b u-boot-with-spl.kwb -t /dev/ttyUSB0

	.PP
	Instruct BootROM to enter boot Xmodem boot mode, send header of
	\fIu-boot-with-spl.kwb\fP kwbimage file via Xmodem at 115200 Bd, then instruct
	BootROM to change baudrate to 5200000 Bd, send data part of the kwbimage
	file via Xmodem at high speed, then change baudrate back to 115200 Bd,
	and finally run terminal program:
	.IP
	.B kwboot -b u-boot-with-spl.kwb -B 5200000 -t /dev/ttyUSB0

	.PP
	Only send \fIu-boot-with-spl.kwb\fP kwbimage file via Xmodem on \fI/dev/ttyUSB0\fP
	at 115200 Bd:
	.IP
	.B kwboot -D u-boot-with-spl.kwb /dev/ttyUSB0

	.PP
	Instruct BootROM to enter console debug mode and run terminal program on
	\fI/dev/ttyUSB0\fP at 115200 Bd:
	.IP
	.B kwboot -d -t /dev/ttyUSB0

	.PP
	Only run terminal program on \fI/dev/ttyUSB0\fP at 115200 Bd:
	.IP
	.B kwboot -t /dev/ttyUSB0

	.SH "SEE ALSO"
	.PP
	\fBmkimage\fP(1), \fBsx\fP(1)

	.SH "AUTHORS"

	Daniel Stodden <daniel.stodden@gmail.com>
	.br
	Luka Perkov <luka@openwrt.org>
	.br
	David Purdy <david.c.purdy@gmail.com>
	.br
	Pali Rohár <pali@kernel.org>
	.br
	Marek Behún <kabel@kernel.org>