| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz> |
| */ |
| |
| #ifndef _CONFIG_SBX81LIFKW_H |
| #define _CONFIG_SBX81LIFKW_H |
| |
| /* |
| * High Level Configuration Options (easy to change) |
| */ |
| #define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ |
| #define CONFIG_KW88F6281 1 /* SOC Name */ |
| #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ |
| #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg |
| |
| /* additions for new ARM relocation support */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| |
| #define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ |
| #define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ |
| #define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */ |
| #define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ |
| #define CONFIG_KIRKWOOD_GPIO 1 |
| |
| /* |
| * NS16550 Configuration |
| */ |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE (-4) |
| #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK |
| #define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE |
| |
| /* |
| * Serial Port configuration |
| * The following definitions let you select what serial you want to use |
| * for your console driver. |
| */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ |
| #define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ |
| #define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ |
| |
| #define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)" |
| #define MTDPARTS_MTDOOPS "errlog" |
| #define CONFIG_DOS_PARTITION |
| |
| /* |
| * Environment variables configurations |
| */ |
| |
| /* |
| * U-Boot bootcode configuration |
| */ |
| |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */ |
| #define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/ |
| |
| /* size in bytes reserved for initial data */ |
| |
| #include <asm/arch/config.h> |
| /* There is no PHY directly connected so don't ask it for link status */ |
| #undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN |
| |
| /* |
| * Other required minimal configurations |
| */ |
| #define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ |
| |
| /* |
| * Ethernet Driver configuration |
| */ |
| #ifdef CONFIG_CMD_NET |
| #define CONFIG_NET_MULTI /* specify more that one ports available */ |
| #define CONFIG_MVGBE /* Enable kirkwood Gbe Controller Driver */ |
| #define CONFIG_MVGBE_PORTS {1, 0} /* enable a single port */ |
| #define CONFIG_PHY_BASE_ADR 0x01 |
| #endif /* CONFIG_CMD_NET */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */ |
| |
| #endif /* _CONFIG_SBX81LIFKW_H */ |