include/configs/CRAYL1.h - platform/external/u-boot - Gitiles

 /*
  * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  * David Updegraff, Cray, Inc.  dave@cray.com: our 405 is walnut-lite..
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
 /*
  * board/config.h - configuration options, board specific
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #define CONFIG_CRAYL1
 /*
  * High Level Configuration Options
  * (easy to change)
  */

 #define CONFIG_405GP		1	/* This is a PPC405 CPU	*/
 #define CONFIG_4xx		    1   /* ...member of PPC405 family */

 /*
  * Note: I make an "image" from U-Boot itself, which prefixes 0x40
  * bytes of header info, hence start address is thus shifted.
  */
 #define	CONFIG_SYS_TEXT_BASE	0xFFFD0040

 #define CONFIG_SYS_CLK_FREQ 25000000
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/

 #define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII		    1	/* MII PHY management */
 #define	CONFIG_PHY_ADDR		1	/* PHY address; handling of ENET */
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* early setup for 405gp */
 #define CONFIG_MISC_INIT_R	1	/* so that a misc_init_r() is called */

 #define CONFIG_CONS_INDEX	1	/* Use UART0			*/
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_serial_clock()

 /* set PRAM to keep U-Boot out, mem= to keep linux out, and initrd_hi to
  * keep possible initrd ramdisk decompression out.  This is in k (1024 bytes)
  #define CONFIG_PRAM			16
  */
 #define	CONFIG_LOADADDR		0x100000	/* where TFTP images go */
 #undef CONFIG_BOOTARGS

 /* Bootcmd is overridden by the bootscript in board/cray/L1
  */
 #define	CONFIG_SYS_AUTOLOAD		"no"
 #define CONFIG_BOOTCOMMAND	"dhcp"

 /*
  * ..during experiments..
  #define CONFIG_SERVERIP         10.0.0.1
  #define CONFIG_ETHADDR          00:40:a6:80:14:5
  */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_PPC4XX
 #define CONFIG_SYS_I2C_PPC4XX_CH0
 #define CONFIG_SDRAM_BANK0		1
 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0		    400000
 #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		    0x7F
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_IDENT_STRING     "Cray L1"
 #define CONFIG_ENV_OVERWRITE     1
 #define	CONFIG_SYS_HZ		             1000	/* decrementer freq: 1 ms ticks	*/
 #define CONFIG_SYS_HUSH_PARSER			1
 #define CONFIG_SOURCE			1


 /*
  * Command line configuration.
  */

 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_BDI
 #define CONFIG_CMD_CONSOLE
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DIAG
 #define CONFIG_CMD_ECHO
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_FLASH
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IMI
 #define CONFIG_CMD_IMMAP
 #define CONFIG_CMD_MEMORY
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_RUN
 #define CONFIG_CMD_SAVEENV
 #define CONFIG_CMD_SETGETDCR
 #define CONFIG_CMD_SOURCE


 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_SUBNETMASK
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_VENDOREX
 #define CONFIG_BOOTP_DNS
 #define CONFIG_BOOTP_BOOTFILESIZE


 /*
  * how many time to fail & restart a net-TFTP before giving up & resetting
  * the board hoping that a reset of net interface might help..
  */
 #define CONFIG_NET_RESET 5

 /*
  * bauds.  Just to make it compile; in our case, I read the base_baud
  * from the DCR anyway, so its kinda-tied to the above ref. clock which in turn
  * drives the system clock.
  */
 #define CONFIG_SYS_BASE_BAUD       403225
 #define CONFIG_SYS_BAUDRATE_TABLE  \
     {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_PROMPT	"=> "				/* Monitor Command Prompt	*/
 #define	CONFIG_SYS_CBSIZE	256				/* Console I/O Buffer Size	*/
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE			/* Boot Argument Buffer Size	*/
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS	16				/* max number of command args	*/


 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* where to load what we get from TFTP */
 #define CONFIG_SYS_EXTBDINFO		1		/* To use extended board_into (bd_t) */
 #define CONFIG_SYS_DRAM_TEST		1

 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_FLASH_BASE		0xFFC00000
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE


 #define CONFIG_SYS_MONITOR_LEN		(192 * 1024)	/* Reserve 192 kB for Monitor	*/

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
 #define CONFIG_SYS_MAX_FLASH_BANKS	 1		/* max number of memory banks		*/
 #define CONFIG_SYS_MAX_FLASH_SECT	 64		/* max number of sectors on one chip	*/
 #define CONFIG_SYS_FLASH_ERASE_TOUT 120000	/* Timeout for Flash Erase (in ms)	*/
 #define CONFIG_SYS_FLASH_WRITE_TOUT 500	/* Timeout for Flash Write (in ms)	*/

 /* BEG ENVIRONNEMENT FLASH: needs to be a whole FlashSector  */
 #define CONFIG_ENV_OFFSET		0x3c8000
 #define CONFIG_ENV_IS_IN_FLASH	1	/* use FLASH for environment vars */
 #define	CONFIG_ENV_SIZE		0x1000	 /* Total Size of Environment area	*/
 #define CONFIG_ENV_SECT_SIZE	0x10000	 /* see README - env sector total size	*/

 /* Memory tests: U-BOOT relocates itself to the top of Ram, so its at
  * 32meg-(128k+some_malloc_space+copy-of-ENV sector)..
  */
 #define CONFIG_SYS_SDRAM_SIZE		32		/* megs of ram */
 #define CONFIG_SYS_MEMTEST_START	0x2000  /* memtest works from the end of */
 									/* the exception vector table */
 									/* to the end of the DRAM  */
 									/* less monitor and malloc area */
 #define CONFIG_SYS_STACK_USAGE		0x10000 /* Reserve 64k for the stack usage */
 #define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* 128k for malloc space */
 #define CONFIG_SYS_MEM_END_USAGE	( CONFIG_SYS_MONITOR_LEN \
 				+ CONFIG_SYS_MALLOC_LEN \
 				+ CONFIG_ENV_SECT_SIZE \
 				+ CONFIG_SYS_STACK_USAGE )

 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 - CONFIG_SYS_MEM_END_USAGE)
 /* END ENVIRONNEMENT FLASH */

 /*
  * Init Memory Controller:
  *
  * BR0/1 and OR0/1 (FLASH)
  */

 #define FLASH_BASE0_PRELIM	CONFIG_SYS_FLASH_BASE	/* FLASH bank #0	*/


 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in OnChipMem )
  */
 #if 1
 /* On Chip Memory location */
 #define CONFIG_SYS_TEMP_STACK_OCM	1
 #define CONFIG_SYS_OCM_DATA_ADDR	0xF0000000
 #define CONFIG_SYS_OCM_DATA_SIZE	0x1000

 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
 #define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/
 #define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 #else
 #define CONFIG_SYS_OCM_DATA_ADDR	0xF0000000
 #define CONFIG_SYS_OCM_DATA_SIZE	0x1000
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR	/* inside of On Chip SRAM    */
 #define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE	/* Size of On Chip SRAM	     */
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 #endif

 /*-----------------------------------------------------------------------
  * Definitions for Serial Presence Detect EEPROM address
  */
 #define EEPROM_WRITE_ADDRESS 0xA0
 #define EEPROM_READ_ADDRESS  0xA1

 #endif	/* __CONFIG_H */
	/*
	* (C) Copyright 2000-2004
	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	* David Updegraff, Cray, Inc. dave@cray.com: our 405 is walnut-lite..
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/
	/*
	* board/config.h - configuration options, board specific
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#define CONFIG_CRAYL1
	/*
	* High Level Configuration Options
	* (easy to change)
	*/

	#define CONFIG_405GP 1 /* This is a PPC405 CPU */
	#define CONFIG_4xx 1 /* ...member of PPC405 family */

	/*
	* Note: I make an "image" from U-Boot itself, which prefixes 0x40
	* bytes of header info, hence start address is thus shifted.
	*/
	#define CONFIG_SYS_TEXT_BASE 0xFFFD0040

	#define CONFIG_SYS_CLK_FREQ 25000000
	#define CONFIG_BAUDRATE 9600
	#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */

	#define CONFIG_PPC4xx_EMAC
	#define CONFIG_MII 1 /* MII PHY management */
	#define CONFIG_PHY_ADDR 1 /* PHY address; handling of ENET */
	#define CONFIG_BOARD_EARLY_INIT_F 1 /* early setup for 405gp */
	#define CONFIG_MISC_INIT_R 1 /* so that a misc_init_r() is called */

	#define CONFIG_CONS_INDEX 1 /* Use UART0 */
	#define CONFIG_SYS_NS16550
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK get_serial_clock()

	/* set PRAM to keep U-Boot out, mem= to keep linux out, and initrd_hi to
	* keep possible initrd ramdisk decompression out. This is in k (1024 bytes)
	#define CONFIG_PRAM 16
	*/
	#define CONFIG_LOADADDR 0x100000 /* where TFTP images go */
	#undef CONFIG_BOOTARGS

	/* Bootcmd is overridden by the bootscript in board/cray/L1
	*/
	#define CONFIG_SYS_AUTOLOAD "no"
	#define CONFIG_BOOTCOMMAND "dhcp"

	/*
	* ..during experiments..
	#define CONFIG_SERVERIP 10.0.0.1
	#define CONFIG_ETHADDR 00:40:a6:80:14:5
	*/
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_PPC4XX
	#define CONFIG_SYS_I2C_PPC4XX_CH0
	#define CONFIG_SDRAM_BANK0 1
	#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
	#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_IDENT_STRING "Cray L1"
	#define CONFIG_ENV_OVERWRITE 1
	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
	#define CONFIG_SYS_HUSH_PARSER 1
	#define CONFIG_SOURCE 1


	/*
	* Command line configuration.
	*/

	#define CONFIG_CMD_ASKENV
	#define CONFIG_CMD_BDI
	#define CONFIG_CMD_CONSOLE
	#define CONFIG_CMD_DATE
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_DIAG
	#define CONFIG_CMD_ECHO
	#define CONFIG_CMD_EEPROM
	#define CONFIG_CMD_FLASH
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_IMI
	#define CONFIG_CMD_IMMAP
	#define CONFIG_CMD_MEMORY
	#define CONFIG_CMD_NET
	#define CONFIG_CMD_REGINFO
	#define CONFIG_CMD_RUN
	#define CONFIG_CMD_SAVEENV
	#define CONFIG_CMD_SETGETDCR
	#define CONFIG_CMD_SOURCE


	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_SUBNETMASK
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_VENDOREX
	#define CONFIG_BOOTP_DNS
	#define CONFIG_BOOTP_BOOTFILESIZE


	/*
	* how many time to fail & restart a net-TFTP before giving up & resetting
	* the board hoping that a reset of net interface might help..
	*/
	#define CONFIG_NET_RESET 5

	/*
	* bauds. Just to make it compile; in our case, I read the base_baud
	* from the DCR anyway, so its kinda-tied to the above ref. clock which in turn
	* drives the system clock.
	*/
	#define CONFIG_SYS_BASE_BAUD 403225
	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */


	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* where to load what we get from TFTP */
	#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
	#define CONFIG_SYS_DRAM_TEST 1

	/*-----------------------------------------------------------------------
	* Start addresses for the final memory configuration
	* (Set up by the startup code)
	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
	*/
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_FLASH_BASE 0xFFC00000
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE


	#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 192 kB for Monitor */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
	/*-----------------------------------------------------------------------
	* FLASH organization
	*/
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */

	/* BEG ENVIRONNEMENT FLASH: needs to be a whole FlashSector */
	#define CONFIG_ENV_OFFSET 0x3c8000
	#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
	#define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment area */
	#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */

	/* Memory tests: U-BOOT relocates itself to the top of Ram, so its at
	* 32meg-(128k+some_malloc_space+copy-of-ENV sector)..
	*/
	#define CONFIG_SYS_SDRAM_SIZE 32 /* megs of ram */
	#define CONFIG_SYS_MEMTEST_START 0x2000 /* memtest works from the end of */
	/* the exception vector table */
	/* to the end of the DRAM */
	/* less monitor and malloc area */
	#define CONFIG_SYS_STACK_USAGE 0x10000 /* Reserve 64k for the stack usage */
	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* 128k for malloc space */
	#define CONFIG_SYS_MEM_END_USAGE ( CONFIG_SYS_MONITOR_LEN \
	+ CONFIG_SYS_MALLOC_LEN \
	+ CONFIG_ENV_SECT_SIZE \
	+ CONFIG_SYS_STACK_USAGE )

	#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 - CONFIG_SYS_MEM_END_USAGE)
	/* END ENVIRONNEMENT FLASH */

	/*
	* Init Memory Controller:
	*
	* BR0/1 and OR0/1 (FLASH)
	*/

	#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */


	/*-----------------------------------------------------------------------
	* Definitions for initial stack pointer and data area (in OnChipMem )
	*/
	#if 1
	/* On Chip Memory location */
	#define CONFIG_SYS_TEMP_STACK_OCM 1
	#define CONFIG_SYS_OCM_DATA_ADDR 0xF0000000
	#define CONFIG_SYS_OCM_DATA_SIZE 0x1000

	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
	#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
	#else
	#define CONFIG_SYS_OCM_DATA_ADDR 0xF0000000
	#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of On Chip SRAM */
	#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of On Chip SRAM */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
	#endif

	/*-----------------------------------------------------------------------
	* Definitions for Serial Presence Detect EEPROM address
	*/
	#define EEPROM_WRITE_ADDRESS 0xA0
	#define EEPROM_READ_ADDRESS 0xA1

	#endif /* __CONFIG_H */