rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/board/Marvell/db64360/sdram_init.c b/board/Marvell/db64360/sdram_init.c
index ecadaf2..d0817d7 100644
--- a/board/Marvell/db64360/sdram_init.c
+++ b/board/Marvell/db64360/sdram_init.c
@@ -312,7 +312,7 @@
} else
dimmInfo->slot = slot; /* start to fill up dimminfo for this "slot" */
-#ifdef CFG_DISPLAY_DIMM_SPD_CONTENT
+#ifdef CONFIG_SYS_DISPLAY_DIMM_SPD_CONTENT
for (i = 0; i <= 127; i++) {
printf ("SPD-EEPROM Byte %3d = %3x (%3d)\n", i, data[i],
@@ -690,16 +690,16 @@
if ((dimmInfo->
minimumCycleTimeAtMaxCasLatancy_LoP
<
- CFG_DDR_SDRAM_CYCLE_COUNT_LOP)
+ CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_LOP)
||
((dimmInfo->
minimumCycleTimeAtMaxCasLatancy_LoP
==
- CFG_DDR_SDRAM_CYCLE_COUNT_LOP)
+ CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_LOP)
&& (dimmInfo->
minimumCycleTimeAtMaxCasLatancy_RoP
<
- CFG_DDR_SDRAM_CYCLE_COUNT_ROP)))
+ CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_ROP)))
{
dimmInfo->
maxClSupported_DDR
@@ -714,16 +714,16 @@
if ((dimmInfo->
minimumCycleTimeAtMaxCasLatancy_LoP
>
- CFG_DDR_SDRAM_CYCLE_COUNT_LOP)
+ CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_LOP)
||
((dimmInfo->
minimumCycleTimeAtMaxCasLatancy_LoP
==
- CFG_DDR_SDRAM_CYCLE_COUNT_LOP)
+ CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_LOP)
&& (dimmInfo->
minimumCycleTimeAtMaxCasLatancy_RoP
>
- CFG_DDR_SDRAM_CYCLE_COUNT_ROP)))
+ CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_ROP)))
{
printf ("*********************************************************\n");
printf ("*** sysClock is higher than SDRAM's allowed frequency ***\n");
@@ -1290,37 +1290,37 @@
case 0x0:
case 0x80: /* refresh period is 15.625 usec */
sdram_config_reg =
- (unsigned int) (((float) 15.625 * (float) CFG_BUS_HZ)
+ (unsigned int) (((float) 15.625 * (float) CONFIG_SYS_BUS_HZ)
/ (float) 1000000.0);
break;
case 0x1:
case 0x81: /* refresh period is 3.9 usec */
sdram_config_reg =
- (unsigned int) (((float) 3.9 * (float) CFG_BUS_HZ) /
+ (unsigned int) (((float) 3.9 * (float) CONFIG_SYS_BUS_HZ) /
(float) 1000000.0);
break;
case 0x2:
case 0x82: /* refresh period is 7.8 usec */
sdram_config_reg =
- (unsigned int) (((float) 7.8 * (float) CFG_BUS_HZ) /
+ (unsigned int) (((float) 7.8 * (float) CONFIG_SYS_BUS_HZ) /
(float) 1000000.0);
break;
case 0x3:
case 0x83: /* refresh period is 31.3 usec */
sdram_config_reg =
- (unsigned int) (((float) 31.3 * (float) CFG_BUS_HZ) /
+ (unsigned int) (((float) 31.3 * (float) CONFIG_SYS_BUS_HZ) /
(float) 1000000.0);
break;
case 0x4:
case 0x84: /* refresh period is 62.5 usec */
sdram_config_reg =
- (unsigned int) (((float) 62.5 * (float) CFG_BUS_HZ) /
+ (unsigned int) (((float) 62.5 * (float) CONFIG_SYS_BUS_HZ) /
(float) 1000000.0);
break;
case 0x5:
case 0x85: /* refresh period is 125 usec */
sdram_config_reg =
- (unsigned int) (((float) 125 * (float) CFG_BUS_HZ) /
+ (unsigned int) (((float) 125 * (float) CONFIG_SYS_BUS_HZ) /
(float) 1000000.0);
break;
default: /* refresh period undefined */
@@ -1807,7 +1807,7 @@
printf ("-- DIMM2 has %d banks\n", dimmInfo2.numOfModuleBanks);
- for (bank_no = 0; bank_no < CFG_DRAM_BANKS; bank_no++) {
+ for (bank_no = 0; bank_no < CONFIG_SYS_DRAM_BANKS; bank_no++) {
/* skip over banks that are not populated */
if (!checkbank[bank_no])
continue;