rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/board/freescale/mpc7448hpc2/tsi108_init.c b/board/freescale/mpc7448hpc2/tsi108_init.c
index 9c40b72..74bb564 100644
--- a/board/freescale/mpc7448hpc2/tsi108_init.c
+++ b/board/freescale/mpc7448hpc2/tsi108_init.c
@@ -88,7 +88,7 @@
{0x00000000, 0x00000240} /* PBA=0xFF00_0000 -> HLP : (Translation Enabled + Byte-Swap)*/
};
-#ifdef CFG_CLK_SPREAD
+#ifdef CONFIG_SYS_CLK_SPREAD
typedef struct {
ulong ctrl0;
ulong ctrl1;
@@ -111,7 +111,7 @@
{0x005c0044, 0x00000039}, /* 6: CG_PB_CLKO = 200 MHz */
{0x004f0044, 0x0000003e} /* 7: CG_PB_CLKO = 233 MHz */
};
-#endif /* CFG_CLK_SPREAD */
+#endif /* CONFIG_SYS_CLK_SPREAD */
/*
* Prosessor Bus Clock (in MHz) defined by CG_PB_SELECT
@@ -129,7 +129,7 @@
ulong i;
/* Detect PB clock freq. */
- i = in32(CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PWRUP_STATUS);
+ i = in32(CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PWRUP_STATUS);
i = (i >> 16) & 0x07; /* Get PB PLL multiplier */
return pb_clk_sel[i] * 1000000;
@@ -146,7 +146,7 @@
ulong i;
gd->mem_clk = 0;
- i = in32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET +
+ i = in32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET +
CG_PWRUP_STATUS);
i = (i >> 20) & 0x07; /* Get GD PLL multiplier */
switch (i) {
@@ -182,7 +182,7 @@
volatile ulong *reg_ptr;
reg_ptr =
- (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x900);
+ (ulong *) (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x900);
for (i = 0; i < 32; i++) {
*reg_ptr++ = 0x00000201; /* SWAP ENABLED */
@@ -194,7 +194,7 @@
/* Setup PB_OCN_BAR2: size 256B + ENable @ 0x0_80000000 */
- out32 (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR2,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR2,
0x80000001);
__asm__ __volatile__ ("sync");
@@ -202,7 +202,7 @@
* read from SDRAM)
*/
- temp = in32(CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR2);
+ temp = in32(CONFIG_SYS_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR2);
__asm__ __volatile__ ("sync");
/*
@@ -221,7 +221,7 @@
* initialize pointer to LUT associated with PB_OCN_BAR1
*/
reg_ptr =
- (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x800);
+ (ulong *) (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x800);
for (i = 0; i < 32; i++) {
*reg_ptr++ = pb2ocn_lut1[i].lower;
@@ -232,73 +232,73 @@
/* Base addresses for CS0, CS1, CS2, CS3 */
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_ADDR,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_ADDR,
0x00000000);
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_ADDR,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_ADDR,
0x00100000);
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_ADDR,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_ADDR,
0x00200000);
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_ADDR,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_ADDR,
0x00300000);
__asm__ __volatile__ ("sync");
/* Masks for HLP banks */
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_MASK,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_MASK,
0xFFF00000);
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_MASK,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_MASK,
0xFFF00000);
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_MASK,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_MASK,
0xFFF00000);
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_MASK,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_MASK,
0xFFF00000);
__asm__ __volatile__ ("sync");
/* Set CTRL0 values for banks */
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_CTRL0,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_CTRL0,
0x7FFC44C2);
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_CTRL0,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_CTRL0,
0x7FFC44C0);
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_CTRL0,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_CTRL0,
0x7FFC44C0);
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL0,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL0,
0x7FFC44C2);
__asm__ __volatile__ ("sync");
/* Set banks to latched mode, enabled, and other default settings */
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_CTRL1,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_CTRL1,
0x7C0F2000);
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_CTRL1,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_CTRL1,
0x7C0F2000);
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_CTRL1,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_CTRL1,
0x7C0F2000);
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL1,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL1,
0x7C0F2000);
__asm__ __volatile__ ("sync");
@@ -306,7 +306,7 @@
* Set new value for PB_OCN_BAR1: switch from BOOT to LUT mode.
* value for PB_OCN_BAR1: (BA-0xE000_0000 + size 512MB + ENable)
*/
- out32 (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1,
0xE0000011);
__asm__ __volatile__ ("sync");
@@ -314,7 +314,7 @@
* immediate read from SDRAM)
*/
- temp = in32(CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1);
+ temp = in32(CONFIG_SYS_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1);
__asm__ __volatile__ ("sync");
/*
@@ -341,7 +341,7 @@
temp = get_cpu_type ();
if ((CPU_750FX == temp) || (CPU_750GX == temp))
- out32 (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_MCMD,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_MCMD,
0x00009955);
#endif /* DISABLE_PBM */
@@ -351,27 +351,27 @@
*/
/* Map PCI/X Configuration Space (16MB @ 0x0_FE000000) */
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET +
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET +
PCI_PFAB_BAR0_UPPER, 0);
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_BAR0,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_BAR0,
0xFB000001);
__asm__ __volatile__ ("sync");
/* Set Bus Number for the attached PCI/X bus (we will use 0 for NB) */
- temp = in32(CFG_TSI108_CSR_BASE +
+ temp = in32(CONFIG_SYS_TSI108_CSR_BASE +
TSI108_PCI_REG_OFFSET + PCI_PCIX_STAT);
temp &= ~0xFF00; /* Clear the BUS_NUM field */
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PCIX_STAT,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PCIX_STAT,
temp);
/* Map PCI/X IO Space (64KB @ 0x0_FD000000) takes one 16MB LUT entry */
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_IO_UPPER,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_IO_UPPER,
0);
__asm__ __volatile__ ("sync");
@@ -379,7 +379,7 @@
* and maps it as a IO address.
*/
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_IO,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_IO,
0x00000001);
__asm__ __volatile__ ("sync");
@@ -405,7 +405,7 @@
*/
reg_ptr =
- (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + 0x500);
+ (ulong *) (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + 0x500);
#ifdef DISABLE_PBM
@@ -442,7 +442,7 @@
__asm__ __volatile__ ("eieio");
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES,
reg_val);
__asm__ __volatile__ ("sync");
@@ -450,9 +450,9 @@
* ( 0 is the best choice for easy mapping)
*/
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR2,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR2,
0x00000000);
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR2_UPPER,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR2_UPPER,
0x00000000);
__asm__ __volatile__ ("sync");
@@ -470,7 +470,7 @@
* set pointer to LUT associated with PCI P2O_BAR3
*/
reg_ptr =
- (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + 0x600);
+ (ulong *) (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + 0x600);
reg_val = 0x00000004; /* Destination port = SDC */
@@ -490,19 +490,19 @@
/* Configure PCI P2O_BAR3 (size = 512MB, Enabled) */
reg_val =
- in32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET +
+ in32(CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET +
PCI_P2O_PAGE_SIZES);
reg_val &= ~0x00FF;
reg_val |= 0x0071;
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES,
reg_val);
__asm__ __volatile__ ("sync");
/* Set 64-bit base PCI bus address for window (0x20000000) */
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR3_UPPER,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR3_UPPER,
0x00000000);
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR3,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR3,
0x20000000);
__asm__ __volatile__ ("sync");
@@ -511,17 +511,17 @@
#ifdef ENABLE_PCI_CSR_BAR
/* open if required access to Tsi108 CSRs from the PCI/X bus */
/* enable BAR0 on the PCI/X bus */
- reg_val = in32(CFG_TSI108_CSR_BASE +
+ reg_val = in32(CONFIG_SYS_TSI108_CSR_BASE +
TSI108_PCI_REG_OFFSET + PCI_MISC_CSR);
reg_val |= 0x02;
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_MISC_CSR,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_MISC_CSR,
reg_val);
__asm__ __volatile__ ("sync");
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR0_UPPER,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR0_UPPER,
0x00000000);
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR0,
- CFG_TSI108_CSR_BASE);
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR0,
+ CONFIG_SYS_TSI108_CSR_BASE);
__asm__ __volatile__ ("sync");
#endif
@@ -530,9 +530,9 @@
* Finally enable PCI/X Bus Master and Memory Space access
*/
- reg_val = in32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR);
+ reg_val = in32(CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR);
reg_val |= 0x06;
- out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR, reg_val);
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR, reg_val);
__asm__ __volatile__ ("sync");
#endif /* CONFIG_PCI */
@@ -546,10 +546,10 @@
* PB_INT[3] -> MCP (CPU1)
* Set interrupt controller outputs as Level_Sensitive/Active_Low
*/
- out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(0), 0x02);
- out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(1), 0x02);
- out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(2), 0x02);
- out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(3), 0x02);
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(0), 0x02);
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(1), 0x02);
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(2), 0x02);
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(3), 0x02);
__asm__ __volatile__ ("sync");
/*
@@ -584,42 +584,42 @@
int misc_init_r (void)
{
-#ifdef CFG_CLK_SPREAD /* Initialize Spread-Spectrum Clock generation */
+#ifdef CONFIG_SYS_CLK_SPREAD /* Initialize Spread-Spectrum Clock generation */
ulong i;
/* Ensure that Spread-Spectrum is disabled */
- out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, 0);
- out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0, 0);
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, 0);
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0, 0);
/* Initialize PLL1: CG_PCI_CLK , internal OCN_CLK
* Uses pre-calculated value for Fout = 800 MHz, Fs = 30 kHz, D = 0.5%
*/
- out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0,
0x002e0044); /* D = 0.25% */
- out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL1,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL1,
0x00000039); /* BWADJ */
/* Initialize PLL0: CG_PB_CLKO */
/* Detect PB clock freq. */
- i = in32(CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PWRUP_STATUS);
+ i = in32(CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PWRUP_STATUS);
i = (i >> 16) & 0x07; /* Get PB PLL multiplier */
- out32 (CFG_TSI108_CSR_BASE +
+ out32 (CONFIG_SYS_TSI108_CSR_BASE +
TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, pll0_config[i].ctrl0);
- out32 (CFG_TSI108_CSR_BASE +
+ out32 (CONFIG_SYS_TSI108_CSR_BASE +
TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL1, pll0_config[i].ctrl1);
/* Wait and set SSEN for both PLL0 and 1 */
udelay (1000);
- out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0,
+ out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0,
0x802e0044); /* D=0.25% */
- out32 (CFG_TSI108_CSR_BASE +
+ out32 (CONFIG_SYS_TSI108_CSR_BASE +
TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0,
0x80000000 | pll0_config[i].ctrl0);
-#endif /* CFG_CLK_SPREAD */
+#endif /* CONFIG_SYS_CLK_SPREAD */
-#ifdef CFG_L2
+#ifdef CONFIG_SYS_L2
l2cache_enable ();
#endif
printf ("BUS: %lu MHz\n", gd->bus_clk / 1000000);