board/bf537-stamp/spi_flash.c - platform/external/u-boot - Gitiles

 /*
  * SPI flash driver
  *
  * Enter bugs at http://blackfin.uclinux.org/
  *
  * Copyright (c) 2005-2007 Analog Devices Inc.
  *
  * Licensed under the GPL-2 or later.
  */

 /* Configuration options:
  * CONFIG_SPI_BAUD - value to load into SPI_BAUD (divisor of SCLK to get SPI CLK)
  * CONFIG_SPI_FLASH_SLOW_READ - force usage of the slower read
  *		WARNING: make sure your SCLK + SPI_BAUD is slow enough
  */

 #include <common.h>
 #include <malloc.h>
 #include <asm/io.h>
 #include <asm/mach-common/bits/spi.h>

 /* Forcibly phase out these */
 #ifdef CONFIG_SPI_FLASH_NUM_SECTORS
 # error do not set CONFIG_SPI_FLASH_NUM_SECTORS
 #endif
 #ifdef CONFIG_SPI_FLASH_SECTOR_SIZE
 # error do not set CONFIG_SPI_FLASH_SECTOR_SIZE
 #endif

 #if defined(CONFIG_SPI)

 struct flash_info {
 	char     *name;
 	uint16_t id;
 	unsigned sector_size;
 	unsigned num_sectors;
 };

 /* SPI Speeds: 50 MHz / 33 MHz */
 static struct flash_info flash_spansion_serial_flash[] = {
 	{ "S25FL016", 0x0215, 64 * 1024, 32 },
 	{ "S25FL032", 0x0216, 64 * 1024, 64 },
 	{ "S25FL064", 0x0217, 64 * 1024, 128 },
 	{ "S25FL0128", 0x0218, 256 * 1024, 64 },
 	{ NULL, 0, 0, 0 }
 };

 /* SPI Speeds: 50 MHz / 20 MHz */
 static struct flash_info flash_st_serial_flash[] = {
 	{ "m25p05", 0x2010, 32 * 1024, 2 },
 	{ "m25p10", 0x2011, 32 * 1024, 4 },
 	{ "m25p20", 0x2012, 64 * 1024, 4 },
 	{ "m25p40", 0x2013, 64 * 1024, 8 },
 	{ "m25p16", 0x2015, 64 * 1024, 32 },
 	{ "m25p32", 0x2016, 64 * 1024, 64 },
 	{ "m25p64", 0x2017, 64 * 1024, 128 },
 	{ "m25p128", 0x2018, 256 * 1024, 64 },
 	{ NULL, 0, 0, 0 }
 };

 /* SPI Speeds: 66 MHz / 33 MHz */
 static struct flash_info flash_atmel_dataflash[] = {
 	{ "AT45DB011x", 0x0c, 264, 512 },
 	{ "AT45DB021x", 0x14, 264, 1025 },
 	{ "AT45DB041x", 0x1c, 264, 2048 },
 	{ "AT45DB081x", 0x24, 264, 4096 },
 	{ "AT45DB161x", 0x2c, 528, 4096 },
 	{ "AT45DB321x", 0x34, 528, 8192 },
 	{ "AT45DB642x", 0x3c, 1056, 8192 },
 	{ NULL, 0, 0, 0 }
 };

 /* SPI Speed: 50 MHz / 25 MHz or 40 MHz / 20 MHz */
 static struct flash_info flash_winbond_serial_flash[] = {
 	{ "W25X10", 0x3011, 16 * 256, 32 },
 	{ "W25X20", 0x3012, 16 * 256, 64 },
 	{ "W25X40", 0x3013, 16 * 256, 128 },
 	{ "W25X80", 0x3014, 16 * 256, 256 },
 	{ "W25P80", 0x2014, 256 * 256, 16 },
 	{ "W25P16", 0x2015, 256 * 256, 32 },
 	{ NULL, 0, 0, 0 }
 };

 struct flash_ops {
 	uint8_t read, write, erase, status;
 };

 #ifdef CONFIG_SPI_FLASH_SLOW_READ
 # define OP_READ 0x03
 #else
 # define OP_READ 0x0B
 #endif
 static struct flash_ops flash_st_ops = {
 	.read = OP_READ,
 	.write = 0x02,
 	.erase = 0xD8,
 	.status = 0x05,
 };

 static struct flash_ops flash_atmel_ops = {
 	.read = OP_READ,
 	.write = 0x82,
 	.erase = 0x81,
 	.status = 0xD7,
 };

 static struct flash_ops flash_winbond_ops = {
 	.read = OP_READ,
 	.write = 0x02,
 	.erase = 0x20,
 	.status = 0x05,
 };

 struct manufacturer_info {
 	const char *name;
 	uint8_t id;
 	struct flash_info *flashes;
 	struct flash_ops *ops;
 };

 static struct {
 	struct manufacturer_info *manufacturer;
 	struct flash_info *flash;
 	struct flash_ops *ops;
 	uint8_t manufacturer_id, device_id1, device_id2;
 	unsigned int write_length;
 	unsigned long sector_size, num_sectors;
 } flash;

 enum {
 	JED_MANU_SPANSION = 0x01,
 	JED_MANU_ST       = 0x20,
 	JED_MANU_ATMEL    = 0x1F,
 	JED_MANU_WINBOND  = 0xEF,
 };

 static struct manufacturer_info flash_manufacturers[] = {
 	{
 		.name = "Spansion",
 		.id = JED_MANU_SPANSION,
 		.flashes = flash_spansion_serial_flash,
 		.ops = &flash_st_ops,
 	},
 	{
 		.name = "ST",
 		.id = JED_MANU_ST,
 		.flashes = flash_st_serial_flash,
 		.ops = &flash_st_ops,
 	},
 	{
 		.name = "Atmel",
 		.id = JED_MANU_ATMEL,
 		.flashes = flash_atmel_dataflash,
 		.ops = &flash_atmel_ops,
 	},
 	{
 		.name = "Winbond",
 		.id = JED_MANU_WINBOND,
 		.flashes = flash_winbond_serial_flash,
 		.ops = &flash_winbond_ops,
 	},
 };

 #define	TIMEOUT	5000	/* timeout of 5 seconds */

 /* BF54x support */
 #ifndef pSPI_CTL
 # define pSPI_CTL  pSPI0_CTL
 # define pSPI_BAUD pSPI0_BAUD
 # define pSPI_FLG  pSPI0_FLG
 # define pSPI_RDBR pSPI0_RDBR
 # define pSPI_STAT pSPI0_STAT
 # define pSPI_TDBR pSPI0_TDBR
 # define SPI0_SCK	0x0001
 # define SPI0_MOSI	0x0004
 # define SPI0_MISO	0x0002
 # define SPI0_SEL1	0x0010
 #endif

 /* Default to the SPI SSEL that we boot off of:
  *	BF54x, BF537, (everything new?): SSEL1
  *	BF533, BF561: SSEL2
  */
 #ifndef CONFIG_SPI_FLASH_SSEL
 # if defined(__ADSPBF531__) || defined(__ADSPBF532__) || \
      defined(__ADSPBF533__) || defined(__ADSPBF561__)
 #  define CONFIG_SPI_FLASH_SSEL 2
 # else
 #  define CONFIG_SPI_FLASH_SSEL 1
 # endif
 #endif
 #define SSEL_MASK (1 << CONFIG_SPI_FLASH_SSEL)

 static void SPI_INIT(void)
 {
 	/* [#3541] This delay appears to be necessary, but not sure
 	 * exactly why as the history behind it is non-existant.
 	 */
 	udelay(CONFIG_CCLK_HZ / 25000000);

 	/* enable SPI pins: SSEL, MOSI, MISO, SCK */
 #ifdef __ADSPBF54x__
 	*pPORTE_FER |= (SPI0_SCK | SPI0_MOSI | SPI0_MISO | SPI0_SEL1);
 #elif defined(__ADSPBF534__) || defined(__ADSPBF536__) || defined(__ADSPBF537__)
 	*pPORTF_FER |= (PF10 | PF11 | PF12 | PF13);
 #elif defined(__ADSPBF52x__)
 	bfin_write_PORTG_MUX((bfin_read_PORTG_MUX() & ~PORT_x_MUX_0_MASK) | PORT_x_MUX_0_FUNC_3);
 	bfin_write_PORTG_FER(bfin_read_PORTG_FER() | PG1 | PG2 | PG3 | PG4);
 #endif

 	/* initate communication upon write of TDBR */
 	*pSPI_CTL = (SPE|MSTR|CPHA|CPOL|0x01);
 	*pSPI_BAUD = CONFIG_SPI_BAUD;
 }

 static void SPI_DEINIT(void)
 {
 	/* put SPI settings back to reset state */
 	*pSPI_CTL = 0x0400;
 	*pSPI_BAUD = 0;
 	SSYNC();
 }

 static void SPI_ON(void)
 {
 	/* toggle SSEL to reset the device so it'll take a new command */
 	*pSPI_FLG = 0xFF00 | SSEL_MASK;
 	SSYNC();

 	*pSPI_FLG = ((0xFF & ~SSEL_MASK) << 8) | SSEL_MASK;
 	SSYNC();
 }

 static void SPI_OFF(void)
 {
 	/* put SPI settings back to reset state */
 	*pSPI_FLG = 0xFF00;
 	SSYNC();
 }

 static uint8_t spi_write_read_byte(uint8_t transmit)
 {
 	*pSPI_TDBR = transmit;
 	SSYNC();

 	while ((*pSPI_STAT & TXS))
 		if (ctrlc())
 			break;
 	while (!(*pSPI_STAT & SPIF))
 		if (ctrlc())
 			break;
 	while (!(*pSPI_STAT & RXS))
 		if (ctrlc())
 			break;

 	/* Read dummy to empty the receive register */
 	return *pSPI_RDBR;
 }

 static uint8_t read_status_register(void)
 {
 	uint8_t status_register;

 	/* send instruction to read status register */
 	SPI_ON();
 	spi_write_read_byte(flash.ops->status);
 	/* send dummy to receive the status register */
 	status_register = spi_write_read_byte(0);
 	SPI_OFF();

 	return status_register;
 }

 static int wait_for_ready_status(void)
 {
 	ulong start = get_timer(0);

 	while (get_timer(0) - start < TIMEOUT) {
 		switch (flash.manufacturer_id) {
 		case JED_MANU_SPANSION:
 		case JED_MANU_ST:
 		case JED_MANU_WINBOND:
 			if (!(read_status_register() & 0x01))
 				return 0;
 			break;

 		case JED_MANU_ATMEL:
 			if (read_status_register() & 0x80)
 				return 0;
 			break;
 		}

 		if (ctrlc()) {
 			puts("\nAbort\n");
 			return -1;
 		}
 	}

 	puts("Timeout\n");
 	return -1;
 }

 /* Request and read the manufacturer and device id of parts which
  * are compatible with the JEDEC standard (JEP106) and use that to
  * setup other operating conditions.
  */
 static int spi_detect_part(void)
 {
 	uint16_t dev_id;
 	size_t i;

 	static char called_init;
 	if (called_init)
 		return 0;

 	SPI_ON();

 	/* Send the request for the part identification */
 	spi_write_read_byte(0x9F);

 	/* Now read in the manufacturer id bytes */
 	do {
 		flash.manufacturer_id = spi_write_read_byte(0);
 		if (flash.manufacturer_id == 0x7F)
 			puts("Warning: unhandled manufacturer continuation byte!\n");
 	} while (flash.manufacturer_id == 0x7F);

 	/* Now read in the first device id byte */
 	flash.device_id1 = spi_write_read_byte(0);

 	/* Now read in the second device id byte */
 	flash.device_id2 = spi_write_read_byte(0);

 	SPI_OFF();

 	dev_id = (flash.device_id1 << 8) | flash.device_id2;

 	for (i = 0; i < ARRAY_SIZE(flash_manufacturers); ++i) {
 		if (flash.manufacturer_id == flash_manufacturers[i].id)
 			break;
 	}
 	if (i == ARRAY_SIZE(flash_manufacturers))
 		goto unknown;

 	flash.manufacturer = &flash_manufacturers[i];
 	flash.ops = flash_manufacturers[i].ops;

 	switch (flash.manufacturer_id) {
 	case JED_MANU_SPANSION:
 	case JED_MANU_ST:
 	case JED_MANU_WINBOND:
 		for (i = 0; flash.manufacturer->flashes[i].name; ++i) {
 			if (dev_id == flash.manufacturer->flashes[i].id)
 				break;
 		}
 		if (!flash.manufacturer->flashes[i].name)
 			goto unknown;

 		flash.flash = &flash.manufacturer->flashes[i];
 		flash.sector_size = flash.flash->sector_size;
 		flash.num_sectors = flash.flash->num_sectors;
 		flash.write_length = 256;
 		break;

 	case JED_MANU_ATMEL: {
 		uint8_t status = read_status_register();

 		for (i = 0; flash.manufacturer->flashes[i].name; ++i) {
 			if ((status & 0x3c) == flash.manufacturer->flashes[i].id)
 				break;
 		}
 		if (!flash.manufacturer->flashes[i].name)
 			goto unknown;

 		flash.flash = &flash.manufacturer->flashes[i];
 		flash.sector_size = flash.flash->sector_size;
 		flash.num_sectors = flash.flash->num_sectors;

 		/* see if flash is in "power of 2" mode */
 		if (status & 0x1)
 			flash.sector_size &= ~(1 << (ffs(flash.sector_size) - 1));

 		flash.write_length = flash.sector_size;
 		break;
 	}
 	}

 	called_init = 1;
 	return 0;

  unknown:
 	printf("Unknown SPI device: 0x%02X 0x%02X 0x%02X\n",
 		flash.manufacturer_id, flash.device_id1, flash.device_id2);
 	return 1;
 }

 /*
  * Function:    spi_init_f
  * Description: Init SPI-Controller (ROM part)
  * return:      ---
  */
 void spi_init_f(void)
 {
 }

 /*
  * Function:    spi_init_r
  * Description: Init SPI-Controller (RAM part) -
  *		 The malloc engine is ready and we can move our buffers to
  *		 normal RAM
  *  return:      ---
  */
 void spi_init_r(void)
 {
 #if defined(CONFIG_POST) && (CONFIG_POST & CONFIG_SYS_POST_SPI)
 	/* Our testing strategy here is pretty basic:
 	 *  - fill src memory with an 8-bit pattern
 	 *  - write the src memory to the SPI flash
 	 *  - read the SPI flash into the dst memory
 	 *  - compare src and dst memory regions
 	 *  - repeat a few times
 	 * The variations we test for:
 	 *  - change the 8-bit pattern a bit
 	 *  - change the read/write block size so we know:
 	 *    - writes smaller/equal/larger than the buffer work
 	 *    - writes smaller/equal/larger than the sector work
 	 *  - change the SPI offsets so we know:
 	 *    - writing partial sectors works
 	 */
 	uint8_t *mem_src, *mem_dst;
 	size_t i, c, l, o;
 	size_t test_count, errors;
 	uint8_t pattern;

 	SPI_INIT();

 	if (spi_detect_part())
 		goto out;
 	eeprom_info();

 	ulong lengths[] = {
 		flash.write_length,
 		flash.write_length * 2,
 		flash.write_length / 2,
 		flash.sector_size,
 		flash.sector_size * 2,
 		flash.sector_size / 2
 	};
 	ulong offsets[] = {
 		0,
 		flash.write_length,
 		flash.write_length * 2,
 		flash.write_length / 2,
 		flash.write_length / 4,
 		flash.sector_size,
 		flash.sector_size * 2,
 		flash.sector_size / 2,
 		flash.sector_size / 4,
 	};

 	/* the exact addresses are arbitrary ... they just need to not overlap */
 	mem_src = (void *)(0);
 	mem_dst = (void *)(max(flash.write_length, flash.sector_size) * 2);

 	test_count = 0;
 	errors = 0;
 	pattern = 0x00;

 	for (i = 0; i < 16; ++i) {	/* 16 = 8 bits * 2 iterations */
 		for (l = 0; l < ARRAY_SIZE(lengths); ++l) {
 			for (o = 0; o < ARRAY_SIZE(offsets); ++o) {
 				ulong len = lengths[l];
 				ulong off = offsets[o];

 				printf("Testing pattern 0x%02X of length %5lu and offset %5lu: ", pattern, len, off);

 				/* setup the source memory region */
 				memset(mem_src, pattern, len);

 				test_count += 4;
 				for (c = 0; c < 4; ++c) {	/* 4 is just a random repeat count */
 					if (ctrlc()) {
 						puts("\nAbort\n");
 						goto out;
 					}

 					/* make sure background fill pattern != pattern */
 					memset(mem_dst, pattern ^ 0xFF, len);

 					/* write out the source memory and then read it back and compare */
 					eeprom_write(0, off, mem_src, len);
 					eeprom_read(0, off, mem_dst, len);

 					if (memcmp(mem_src, mem_dst, len)) {
 						for (c = 0; c < len; ++c)
 							if (mem_src[c] != mem_dst[c])
 								break;
 						printf(" FAIL @ offset %u, skipping repeats ", c);
 						++errors;
 						break;
 					}

 					/* XXX: should shrink write region here to test with
 					 * leading/trailing canaries so we know surrounding
 					 * bytes don't get screwed.
 					 */
 				}
 				puts("\n");
 			}
 		}

 		/* invert the pattern every other run and shift out bits slowly */
 		pattern ^= 0xFF;
 		if (i % 2)
 			pattern = (pattern | 0x01) << 1;
 	}

 	if (errors)
 		printf("SPI FAIL: Out of %i tests, there were %i errors ;(\n", test_count, errors);
 	else
 		printf("SPI PASS: %i tests worked!\n", test_count);

  out:
 	SPI_DEINIT();

 #endif
 }

 static void transmit_address(uint32_t addr)
 {
 	/* Send the highest byte of the 24 bit address at first */
 	spi_write_read_byte(addr >> 16);
 	/* Send the middle byte of the 24 bit address  at second */
 	spi_write_read_byte(addr >> 8);
 	/* Send the lowest byte of the 24 bit address finally */
 	spi_write_read_byte(addr);
 }

 /*
  * Read a value from flash for verify purpose
  * Inputs:	unsigned long ulStart - holds the SPI start address
  *			int pnData - pointer to store value read from flash
  *			long lCount - number of elements to read
  */
 static int read_flash(unsigned long address, long count, uchar *buffer)
 {
 	size_t i;

 	/* Send the read command to SPI device */
 	SPI_ON();
 	spi_write_read_byte(flash.ops->read);
 	transmit_address(address);

 #ifndef CONFIG_SPI_FLASH_SLOW_READ
 	/* Send dummy byte when doing SPI fast reads */
 	spi_write_read_byte(0);
 #endif

 	/* After the SPI device address has been placed on the MOSI pin the data can be */
 	/* received on the MISO pin. */
 	for (i = 1; i <= count; ++i) {
 		*buffer++ = spi_write_read_byte(0);
 		if (i % flash.sector_size == 0)
 			puts(".");
 	}

 	SPI_OFF();

 	return 0;
 }

 static int enable_writing(void)
 {
 	ulong start;

 	if (flash.manufacturer_id == JED_MANU_ATMEL)
 		return 0;

 	/* A write enable instruction must previously have been executed */
 	SPI_ON();
 	spi_write_read_byte(0x06);
 	SPI_OFF();

 	/* The status register will be polled to check the write enable latch "WREN" */
 	start = get_timer(0);
 	while (get_timer(0) - start < TIMEOUT) {
 		if (read_status_register() & 0x02)
 			return 0;

 		if (ctrlc()) {
 			puts("\nAbort\n");
 			return -1;
 		}
 	}

 	puts("Timeout\n");
 	return -1;
 }

 static long address_to_sector(unsigned long address)
 {
 	if (address > (flash.num_sectors * flash.sector_size) - 1)
 		return -1;
 	return address / flash.sector_size;
 }

 static int erase_sector(int address)
 {
 	/* sector gets checked in higher function, so assume it's valid
 	 * here and figure out the offset of the sector in flash
 	 */
 	if (enable_writing())
 		return -1;

 	/*
 	 * Send the erase block command to the flash followed by the 24 address
 	 * to point to the start of a sector
 	 */
 	SPI_ON();
 	spi_write_read_byte(flash.ops->erase);
 	transmit_address(address);
 	SPI_OFF();

 	return wait_for_ready_status();
 }

 /* Write [count] bytes out of [buffer] into the given SPI [address] */
 static long write_flash(unsigned long address, long count, uchar *buffer)
 {
 	long i, write_buffer_size;

 	if (enable_writing())
 		return -1;

 	/* Send write command followed by the 24 bit address */
 	SPI_ON();
 	spi_write_read_byte(flash.ops->write);
 	transmit_address(address);

 	/* Shoot out a single write buffer */
 	write_buffer_size = min(count, flash.write_length);
 	for (i = 0; i < write_buffer_size; ++i)
 		spi_write_read_byte(buffer[i]);

 	SPI_OFF();

 	/* Wait for the flash to do its thing */
 	if (wait_for_ready_status()) {
 		puts("SPI Program Time out! ");
 		return -1;
 	}

 	return i;
 }

 /* Write [count] bytes out of [buffer] into the given SPI [address] */
 static int write_sector(unsigned long address, long count, uchar *buffer)
 {
 	long write_cnt;

 	while (count != 0) {
 		write_cnt = write_flash(address, count, buffer);
 		if (write_cnt == -1)
 			return -1;

 		/* Now that we've sent some bytes out to the flash, update
 		 * our counters a bit
 		 */
 		count -= write_cnt;
 		address += write_cnt;
 		buffer += write_cnt;
 	}

 	/* return the appropriate error code */
 	return 0;
 }

 /*
  * Function:    spi_write
  */
 ssize_t spi_write(uchar *addr, int alen, uchar *buffer, int len)
 {
 	unsigned long offset;
 	int start_sector, end_sector;
 	int start_byte, end_byte;
 	uchar *temp = NULL;
 	int num, ret = 0;

 	SPI_INIT();

 	if (spi_detect_part())
 		goto out;

 	offset = addr[0] << 16 | addr[1] << 8 | addr[2];

 	/* Get the start block number */
 	start_sector = address_to_sector(offset);
 	if (start_sector == -1) {
 		puts("Invalid sector! ");
 		goto out;
 	}
 	end_sector = address_to_sector(offset + len - 1);
 	if (end_sector == -1) {
 		puts("Invalid sector! ");
 		goto out;
 	}

 	/* Since flashes operate in sector units but the eeprom command
 	 * operates as a continuous stream of bytes, we need to emulate
 	 * the eeprom behavior.  So here we read in the sector, overlay
 	 * any bytes we're actually modifying, erase the sector, and
 	 * then write back out the new sector.
 	 */
 	temp = malloc(flash.sector_size);
 	if (!temp) {
 		puts("Malloc for sector failed! ");
 		goto out;
 	}

 	for (num = start_sector; num <= end_sector; num++) {
 		unsigned long address = num * flash.sector_size;

 		/* XXX: should add an optimization when spanning sectors:
 		 * No point in reading in a sector if we're going to be
 		 * clobbering the whole thing.  Need to also add a test
 		 * case to make sure the optimization is correct.
 		 */
 		if (read_flash(address, flash.sector_size, temp)) {
 			puts("Read sector failed! ");
 			len = 0;
 			break;
 		}

 		start_byte = max(address, offset);
 		end_byte = address + flash.sector_size - 1;
 		if (end_byte > (offset + len))
 			end_byte = (offset + len - 1);

 		memcpy(temp + start_byte - address,
 			buffer + start_byte - offset,
 			end_byte - start_byte + 1);

 		if (erase_sector(address)) {
 			puts("Erase sector failed! ");
 			goto out;
 		}

 		if (write_sector(address, flash.sector_size, temp)) {
 			puts("Write sector failed! ");
 			goto out;
 		}

 		puts(".");
 	}

 	ret = len;

  out:
 	free(temp);

 	SPI_DEINIT();

 	return ret;
 }

 /*
  * Function: spi_read
  */
 ssize_t spi_read(uchar *addr, int alen, uchar *buffer, int len)
 {
 	unsigned long offset;

 	SPI_INIT();

 	if (spi_detect_part())
 		len = 0;
 	else {
 		offset = addr[0] << 16 | addr[1] << 8 | addr[2];
 		read_flash(offset, len, buffer);
 	}

 	SPI_DEINIT();

 	return len;
 }

 /*
  *	Spit out some useful information about the SPI eeprom
  */
 int eeprom_info(void)
 {
 	int ret = 0;

 	SPI_INIT();

 	if (spi_detect_part())
 		ret = 1;
 	else
 		printf("SPI Device: %s 0x%02X (%s) 0x%02X 0x%02X\n"
 			"Parameters: num sectors = %i, sector size = %i, write size = %i\n"
 			"Flash Size: %i mbit (%i mbyte)\n"
 			"Status: 0x%02X\n",
 			flash.flash->name, flash.manufacturer_id, flash.manufacturer->name,
 			flash.device_id1, flash.device_id2, flash.num_sectors,
 			flash.sector_size, flash.write_length,
 			(flash.num_sectors * flash.sector_size) >> 17,
 			(flash.num_sectors * flash.sector_size) >> 20,
 			read_status_register());

 	SPI_DEINIT();

 	return ret;
 }

 #endif
	/*
	* SPI flash driver
	*
	* Enter bugs at http://blackfin.uclinux.org/
	*
	* Copyright (c) 2005-2007 Analog Devices Inc.
	*
	* Licensed under the GPL-2 or later.
	*/

	/* Configuration options:
	* CONFIG_SPI_BAUD - value to load into SPI_BAUD (divisor of SCLK to get SPI CLK)
	* CONFIG_SPI_FLASH_SLOW_READ - force usage of the slower read
	* WARNING: make sure your SCLK + SPI_BAUD is slow enough
	*/

	#include <common.h>
	#include <malloc.h>
	#include <asm/io.h>
	#include <asm/mach-common/bits/spi.h>

	/* Forcibly phase out these */
	#ifdef CONFIG_SPI_FLASH_NUM_SECTORS
	# error do not set CONFIG_SPI_FLASH_NUM_SECTORS
	#endif
	#ifdef CONFIG_SPI_FLASH_SECTOR_SIZE
	# error do not set CONFIG_SPI_FLASH_SECTOR_SIZE
	#endif

	#if defined(CONFIG_SPI)

	struct flash_info {
	char *name;
	uint16_t id;
	unsigned sector_size;
	unsigned num_sectors;
	};

	/* SPI Speeds: 50 MHz / 33 MHz */
	static struct flash_info flash_spansion_serial_flash[] = {
	{ "S25FL016", 0x0215, 64 * 1024, 32 },
	{ "S25FL032", 0x0216, 64 * 1024, 64 },
	{ "S25FL064", 0x0217, 64 * 1024, 128 },
	{ "S25FL0128", 0x0218, 256 * 1024, 64 },
	{ NULL, 0, 0, 0 }
	};

	/* SPI Speeds: 50 MHz / 20 MHz */
	static struct flash_info flash_st_serial_flash[] = {
	{ "m25p05", 0x2010, 32 * 1024, 2 },
	{ "m25p10", 0x2011, 32 * 1024, 4 },
	{ "m25p20", 0x2012, 64 * 1024, 4 },
	{ "m25p40", 0x2013, 64 * 1024, 8 },
	{ "m25p16", 0x2015, 64 * 1024, 32 },
	{ "m25p32", 0x2016, 64 * 1024, 64 },
	{ "m25p64", 0x2017, 64 * 1024, 128 },
	{ "m25p128", 0x2018, 256 * 1024, 64 },
	{ NULL, 0, 0, 0 }
	};

	/* SPI Speeds: 66 MHz / 33 MHz */
	static struct flash_info flash_atmel_dataflash[] = {
	{ "AT45DB011x", 0x0c, 264, 512 },
	{ "AT45DB021x", 0x14, 264, 1025 },
	{ "AT45DB041x", 0x1c, 264, 2048 },
	{ "AT45DB081x", 0x24, 264, 4096 },
	{ "AT45DB161x", 0x2c, 528, 4096 },
	{ "AT45DB321x", 0x34, 528, 8192 },
	{ "AT45DB642x", 0x3c, 1056, 8192 },
	{ NULL, 0, 0, 0 }
	};

	/* SPI Speed: 50 MHz / 25 MHz or 40 MHz / 20 MHz */
	static struct flash_info flash_winbond_serial_flash[] = {
	{ "W25X10", 0x3011, 16 * 256, 32 },
	{ "W25X20", 0x3012, 16 * 256, 64 },
	{ "W25X40", 0x3013, 16 * 256, 128 },
	{ "W25X80", 0x3014, 16 * 256, 256 },
	{ "W25P80", 0x2014, 256 * 256, 16 },
	{ "W25P16", 0x2015, 256 * 256, 32 },
	{ NULL, 0, 0, 0 }
	};

	struct flash_ops {
	uint8_t read, write, erase, status;
	};

	#ifdef CONFIG_SPI_FLASH_SLOW_READ
	# define OP_READ 0x03
	#else
	# define OP_READ 0x0B
	#endif
	static struct flash_ops flash_st_ops = {
	.read = OP_READ,
	.write = 0x02,
	.erase = 0xD8,
	.status = 0x05,
	};

	static struct flash_ops flash_atmel_ops = {
	.read = OP_READ,
	.write = 0x82,
	.erase = 0x81,
	.status = 0xD7,
	};

	static struct flash_ops flash_winbond_ops = {
	.read = OP_READ,
	.write = 0x02,
	.erase = 0x20,
	.status = 0x05,
	};

	struct manufacturer_info {
	const char *name;
	uint8_t id;
	struct flash_info *flashes;
	struct flash_ops *ops;
	};

	static struct {
	struct manufacturer_info *manufacturer;
	struct flash_info *flash;
	struct flash_ops *ops;
	uint8_t manufacturer_id, device_id1, device_id2;
	unsigned int write_length;
	unsigned long sector_size, num_sectors;
	} flash;

	enum {
	JED_MANU_SPANSION = 0x01,
	JED_MANU_ST = 0x20,
	JED_MANU_ATMEL = 0x1F,
	JED_MANU_WINBOND = 0xEF,
	};

	static struct manufacturer_info flash_manufacturers[] = {
	{
	.name = "Spansion",
	.id = JED_MANU_SPANSION,
	.flashes = flash_spansion_serial_flash,
	.ops = &flash_st_ops,
	},
	{
	.name = "ST",
	.id = JED_MANU_ST,
	.flashes = flash_st_serial_flash,
	.ops = &flash_st_ops,
	},
	{
	.name = "Atmel",
	.id = JED_MANU_ATMEL,
	.flashes = flash_atmel_dataflash,
	.ops = &flash_atmel_ops,
	},
	{
	.name = "Winbond",
	.id = JED_MANU_WINBOND,
	.flashes = flash_winbond_serial_flash,
	.ops = &flash_winbond_ops,
	},
	};

	#define TIMEOUT 5000 /* timeout of 5 seconds */

	/* BF54x support */
	#ifndef pSPI_CTL
	# define pSPI_CTL pSPI0_CTL
	# define pSPI_BAUD pSPI0_BAUD
	# define pSPI_FLG pSPI0_FLG
	# define pSPI_RDBR pSPI0_RDBR
	# define pSPI_STAT pSPI0_STAT
	# define pSPI_TDBR pSPI0_TDBR
	# define SPI0_SCK 0x0001
	# define SPI0_MOSI 0x0004
	# define SPI0_MISO 0x0002
	# define SPI0_SEL1 0x0010
	#endif

	/* Default to the SPI SSEL that we boot off of:
	* BF54x, BF537, (everything new?): SSEL1
	* BF533, BF561: SSEL2
	*/
	#ifndef CONFIG_SPI_FLASH_SSEL
	# if defined(__ADSPBF531__) \|\| defined(__ADSPBF532__) \|\| \
	defined(__ADSPBF533__) \|\| defined(__ADSPBF561__)
	# define CONFIG_SPI_FLASH_SSEL 2
	# else
	# define CONFIG_SPI_FLASH_SSEL 1
	# endif
	#endif
	#define SSEL_MASK (1 << CONFIG_SPI_FLASH_SSEL)

	static void SPI_INIT(void)
	{
	/* [#3541] This delay appears to be necessary, but not sure
	* exactly why as the history behind it is non-existant.
	*/
	udelay(CONFIG_CCLK_HZ / 25000000);

	/* enable SPI pins: SSEL, MOSI, MISO, SCK */
	#ifdef __ADSPBF54x__
	*pPORTE_FER \|= (SPI0_SCK \| SPI0_MOSI \| SPI0_MISO \| SPI0_SEL1);
	#elif defined(__ADSPBF534__) \|\| defined(__ADSPBF536__) \|\| defined(__ADSPBF537__)
	*pPORTF_FER \|= (PF10 \| PF11 \| PF12 \| PF13);
	#elif defined(__ADSPBF52x__)
	bfin_write_PORTG_MUX((bfin_read_PORTG_MUX() & ~PORT_x_MUX_0_MASK) \| PORT_x_MUX_0_FUNC_3);
	bfin_write_PORTG_FER(bfin_read_PORTG_FER() \| PG1 \| PG2 \| PG3 \| PG4);
	#endif

	/* initate communication upon write of TDBR */
	*pSPI_CTL = (SPE\|MSTR\|CPHA\|CPOL\|0x01);
	*pSPI_BAUD = CONFIG_SPI_BAUD;
	}

	static void SPI_DEINIT(void)
	{
	/* put SPI settings back to reset state */
	*pSPI_CTL = 0x0400;
	*pSPI_BAUD = 0;
	SSYNC();
	}

	static void SPI_ON(void)
	{
	/* toggle SSEL to reset the device so it'll take a new command */
	*pSPI_FLG = 0xFF00 \| SSEL_MASK;
	SSYNC();

	*pSPI_FLG = ((0xFF & ~SSEL_MASK) << 8) \| SSEL_MASK;
	SSYNC();
	}

	static void SPI_OFF(void)
	{
	/* put SPI settings back to reset state */
	*pSPI_FLG = 0xFF00;
	SSYNC();
	}

	static uint8_t spi_write_read_byte(uint8_t transmit)
	{
	*pSPI_TDBR = transmit;
	SSYNC();

	while ((*pSPI_STAT & TXS))
	if (ctrlc())
	break;
	while (!(*pSPI_STAT & SPIF))
	if (ctrlc())
	break;
	while (!(*pSPI_STAT & RXS))
	if (ctrlc())
	break;

	/* Read dummy to empty the receive register */
	return *pSPI_RDBR;
	}

	static uint8_t read_status_register(void)
	{
	uint8_t status_register;

	/* send instruction to read status register */
	SPI_ON();
	spi_write_read_byte(flash.ops->status);
	/* send dummy to receive the status register */
	status_register = spi_write_read_byte(0);
	SPI_OFF();

	return status_register;
	}

	static int wait_for_ready_status(void)
	{
	ulong start = get_timer(0);

	while (get_timer(0) - start < TIMEOUT) {
	switch (flash.manufacturer_id) {
	case JED_MANU_SPANSION:
	case JED_MANU_ST:
	case JED_MANU_WINBOND:
	if (!(read_status_register() & 0x01))
	return 0;
	break;

	case JED_MANU_ATMEL:
	if (read_status_register() & 0x80)
	return 0;
	break;
	}

	if (ctrlc()) {
	puts("\nAbort\n");
	return -1;
	}
	}

	puts("Timeout\n");
	return -1;
	}

	/* Request and read the manufacturer and device id of parts which
	* are compatible with the JEDEC standard (JEP106) and use that to
	* setup other operating conditions.
	*/
	static int spi_detect_part(void)
	{
	uint16_t dev_id;
	size_t i;

	static char called_init;
	if (called_init)
	return 0;

	SPI_ON();

	/* Send the request for the part identification */
	spi_write_read_byte(0x9F);

	/* Now read in the manufacturer id bytes */
	do {
	flash.manufacturer_id = spi_write_read_byte(0);
	if (flash.manufacturer_id == 0x7F)
	puts("Warning: unhandled manufacturer continuation byte!\n");
	} while (flash.manufacturer_id == 0x7F);

	/* Now read in the first device id byte */
	flash.device_id1 = spi_write_read_byte(0);

	/* Now read in the second device id byte */
	flash.device_id2 = spi_write_read_byte(0);

	SPI_OFF();

	dev_id = (flash.device_id1 << 8) \| flash.device_id2;

	for (i = 0; i < ARRAY_SIZE(flash_manufacturers); ++i) {
	if (flash.manufacturer_id == flash_manufacturers[i].id)
	break;
	}
	if (i == ARRAY_SIZE(flash_manufacturers))
	goto unknown;

	flash.manufacturer = &flash_manufacturers[i];
	flash.ops = flash_manufacturers[i].ops;

	switch (flash.manufacturer_id) {
	case JED_MANU_SPANSION:
	case JED_MANU_ST:
	case JED_MANU_WINBOND:
	for (i = 0; flash.manufacturer->flashes[i].name; ++i) {
	if (dev_id == flash.manufacturer->flashes[i].id)
	break;
	}
	if (!flash.manufacturer->flashes[i].name)
	goto unknown;

	flash.flash = &flash.manufacturer->flashes[i];
	flash.sector_size = flash.flash->sector_size;
	flash.num_sectors = flash.flash->num_sectors;
	flash.write_length = 256;
	break;

	case JED_MANU_ATMEL: {
	uint8_t status = read_status_register();

	for (i = 0; flash.manufacturer->flashes[i].name; ++i) {
	if ((status & 0x3c) == flash.manufacturer->flashes[i].id)
	break;
	}
	if (!flash.manufacturer->flashes[i].name)
	goto unknown;

	flash.flash = &flash.manufacturer->flashes[i];
	flash.sector_size = flash.flash->sector_size;
	flash.num_sectors = flash.flash->num_sectors;

	/* see if flash is in "power of 2" mode */
	if (status & 0x1)
	flash.sector_size &= ~(1 << (ffs(flash.sector_size) - 1));

	flash.write_length = flash.sector_size;
	break;
	}
	}

	called_init = 1;
	return 0;

	unknown:
	printf("Unknown SPI device: 0x%02X 0x%02X 0x%02X\n",
	flash.manufacturer_id, flash.device_id1, flash.device_id2);
	return 1;
	}

	/*
	* Function: spi_init_f
	* Description: Init SPI-Controller (ROM part)
	* return: ---
	*/
	void spi_init_f(void)
	{
	}

	/*
	* Function: spi_init_r
	* Description: Init SPI-Controller (RAM part) -
	* The malloc engine is ready and we can move our buffers to
	* normal RAM
	* return: ---
	*/
	void spi_init_r(void)
	{
	#if defined(CONFIG_POST) && (CONFIG_POST & CONFIG_SYS_POST_SPI)
	/* Our testing strategy here is pretty basic:
	* - fill src memory with an 8-bit pattern
	* - write the src memory to the SPI flash
	* - read the SPI flash into the dst memory
	* - compare src and dst memory regions
	* - repeat a few times
	* The variations we test for:
	* - change the 8-bit pattern a bit
	* - change the read/write block size so we know:
	* - writes smaller/equal/larger than the buffer work
	* - writes smaller/equal/larger than the sector work
	* - change the SPI offsets so we know:
	* - writing partial sectors works
	*/
	uint8_t mem_src, mem_dst;
	size_t i, c, l, o;
	size_t test_count, errors;
	uint8_t pattern;

	SPI_INIT();

	if (spi_detect_part())
	goto out;
	eeprom_info();

	ulong lengths[] = {
	flash.write_length,
	flash.write_length * 2,
	flash.write_length / 2,
	flash.sector_size,
	flash.sector_size * 2,
	flash.sector_size / 2
	};
	ulong offsets[] = {
	0,
	flash.write_length,
	flash.write_length * 2,
	flash.write_length / 2,
	flash.write_length / 4,
	flash.sector_size,
	flash.sector_size * 2,
	flash.sector_size / 2,
	flash.sector_size / 4,
	};

	/* the exact addresses are arbitrary ... they just need to not overlap */
	mem_src = (void *)(0);
	mem_dst = (void )(max(flash.write_length, flash.sector_size) 2);

	test_count = 0;
	errors = 0;
	pattern = 0x00;

	for (i = 0; i < 16; ++i) { /* 16 = 8 bits * 2 iterations */
	for (l = 0; l < ARRAY_SIZE(lengths); ++l) {
	for (o = 0; o < ARRAY_SIZE(offsets); ++o) {
	ulong len = lengths[l];
	ulong off = offsets[o];

	printf("Testing pattern 0x%02X of length %5lu and offset %5lu: ", pattern, len, off);

	/* setup the source memory region */
	memset(mem_src, pattern, len);

	test_count += 4;
	for (c = 0; c < 4; ++c) { /* 4 is just a random repeat count */
	if (ctrlc()) {
	puts("\nAbort\n");
	goto out;
	}

	/* make sure background fill pattern != pattern */
	memset(mem_dst, pattern ^ 0xFF, len);

	/* write out the source memory and then read it back and compare */
	eeprom_write(0, off, mem_src, len);
	eeprom_read(0, off, mem_dst, len);

	if (memcmp(mem_src, mem_dst, len)) {
	for (c = 0; c < len; ++c)
	if (mem_src[c] != mem_dst[c])
	break;
	printf(" FAIL @ offset %u, skipping repeats ", c);
	++errors;
	break;
	}

	/* XXX: should shrink write region here to test with
	* leading/trailing canaries so we know surrounding
	* bytes don't get screwed.
	*/
	}
	puts("\n");
	}
	}

	/* invert the pattern every other run and shift out bits slowly */
	pattern ^= 0xFF;
	if (i % 2)
	pattern = (pattern \| 0x01) << 1;
	}

	if (errors)
	printf("SPI FAIL: Out of %i tests, there were %i errors ;(\n", test_count, errors);
	else
	printf("SPI PASS: %i tests worked!\n", test_count);

	out:
	SPI_DEINIT();

	#endif
	}

	static void transmit_address(uint32_t addr)
	{
	/* Send the highest byte of the 24 bit address at first */
	spi_write_read_byte(addr >> 16);
	/* Send the middle byte of the 24 bit address at second */
	spi_write_read_byte(addr >> 8);
	/* Send the lowest byte of the 24 bit address finally */
	spi_write_read_byte(addr);
	}

	/*
	* Read a value from flash for verify purpose
	* Inputs: unsigned long ulStart - holds the SPI start address
	* int pnData - pointer to store value read from flash
	* long lCount - number of elements to read
	*/
	static int read_flash(unsigned long address, long count, uchar *buffer)
	{
	size_t i;

	/* Send the read command to SPI device */
	SPI_ON();
	spi_write_read_byte(flash.ops->read);
	transmit_address(address);

	#ifndef CONFIG_SPI_FLASH_SLOW_READ
	/* Send dummy byte when doing SPI fast reads */
	spi_write_read_byte(0);
	#endif

	/* After the SPI device address has been placed on the MOSI pin the data can be */
	/* received on the MISO pin. */
	for (i = 1; i <= count; ++i) {
	*buffer++ = spi_write_read_byte(0);
	if (i % flash.sector_size == 0)
	puts(".");
	}

	SPI_OFF();

	return 0;
	}

	static int enable_writing(void)
	{
	ulong start;

	if (flash.manufacturer_id == JED_MANU_ATMEL)
	return 0;

	/* A write enable instruction must previously have been executed */
	SPI_ON();
	spi_write_read_byte(0x06);
	SPI_OFF();

	/* The status register will be polled to check the write enable latch "WREN" */
	start = get_timer(0);
	while (get_timer(0) - start < TIMEOUT) {
	if (read_status_register() & 0x02)
	return 0;

	if (ctrlc()) {
	puts("\nAbort\n");
	return -1;
	}
	}

	puts("Timeout\n");
	return -1;
	}

	static long address_to_sector(unsigned long address)
	{
	if (address > (flash.num_sectors * flash.sector_size) - 1)
	return -1;
	return address / flash.sector_size;
	}

	static int erase_sector(int address)
	{
	/* sector gets checked in higher function, so assume it's valid
	* here and figure out the offset of the sector in flash
	*/
	if (enable_writing())
	return -1;

	/*
	* Send the erase block command to the flash followed by the 24 address
	* to point to the start of a sector
	*/
	SPI_ON();
	spi_write_read_byte(flash.ops->erase);
	transmit_address(address);
	SPI_OFF();

	return wait_for_ready_status();
	}

	/* Write [count] bytes out of [buffer] into the given SPI [address] */
	static long write_flash(unsigned long address, long count, uchar *buffer)
	{
	long i, write_buffer_size;

	if (enable_writing())
	return -1;

	/* Send write command followed by the 24 bit address */
	SPI_ON();
	spi_write_read_byte(flash.ops->write);
	transmit_address(address);

	/* Shoot out a single write buffer */
	write_buffer_size = min(count, flash.write_length);
	for (i = 0; i < write_buffer_size; ++i)
	spi_write_read_byte(buffer[i]);

	SPI_OFF();

	/* Wait for the flash to do its thing */
	if (wait_for_ready_status()) {
	puts("SPI Program Time out! ");
	return -1;
	}

	return i;
	}

	/* Write [count] bytes out of [buffer] into the given SPI [address] */
	static int write_sector(unsigned long address, long count, uchar *buffer)
	{
	long write_cnt;

	while (count != 0) {
	write_cnt = write_flash(address, count, buffer);
	if (write_cnt == -1)
	return -1;

	/* Now that we've sent some bytes out to the flash, update
	* our counters a bit
	*/
	count -= write_cnt;
	address += write_cnt;
	buffer += write_cnt;
	}

	/* return the appropriate error code */
	return 0;
	}

	/*
	* Function: spi_write
	*/
	ssize_t spi_write(uchar addr, int alen, uchar buffer, int len)
	{
	unsigned long offset;
	int start_sector, end_sector;
	int start_byte, end_byte;
	uchar *temp = NULL;
	int num, ret = 0;

	SPI_INIT();

	if (spi_detect_part())
	goto out;

	offset = addr[0] << 16 \| addr[1] << 8 \| addr[2];

	/* Get the start block number */
	start_sector = address_to_sector(offset);
	if (start_sector == -1) {
	puts("Invalid sector! ");
	goto out;
	}
	end_sector = address_to_sector(offset + len - 1);
	if (end_sector == -1) {
	puts("Invalid sector! ");
	goto out;
	}

	/* Since flashes operate in sector units but the eeprom command
	* operates as a continuous stream of bytes, we need to emulate
	* the eeprom behavior. So here we read in the sector, overlay
	* any bytes we're actually modifying, erase the sector, and
	* then write back out the new sector.
	*/
	temp = malloc(flash.sector_size);
	if (!temp) {
	puts("Malloc for sector failed! ");
	goto out;
	}

	for (num = start_sector; num <= end_sector; num++) {
	unsigned long address = num * flash.sector_size;

	/* XXX: should add an optimization when spanning sectors:
	* No point in reading in a sector if we're going to be
	* clobbering the whole thing. Need to also add a test
	* case to make sure the optimization is correct.
	*/
	if (read_flash(address, flash.sector_size, temp)) {
	puts("Read sector failed! ");
	len = 0;
	break;
	}

	start_byte = max(address, offset);
	end_byte = address + flash.sector_size - 1;
	if (end_byte > (offset + len))
	end_byte = (offset + len - 1);

	memcpy(temp + start_byte - address,
	buffer + start_byte - offset,
	end_byte - start_byte + 1);

	if (erase_sector(address)) {
	puts("Erase sector failed! ");
	goto out;
	}

	if (write_sector(address, flash.sector_size, temp)) {
	puts("Write sector failed! ");
	goto out;
	}

	puts(".");
	}

	ret = len;

	out:
	free(temp);

	SPI_DEINIT();

	return ret;
	}

	/*
	* Function: spi_read
	*/
	ssize_t spi_read(uchar addr, int alen, uchar buffer, int len)
	{
	unsigned long offset;

	SPI_INIT();

	if (spi_detect_part())
	len = 0;
	else {
	offset = addr[0] << 16 \| addr[1] << 8 \| addr[2];
	read_flash(offset, len, buffer);
	}

	SPI_DEINIT();

	return len;
	}

	/*
	* Spit out some useful information about the SPI eeprom
	*/
	int eeprom_info(void)
	{
	int ret = 0;

	SPI_INIT();

	if (spi_detect_part())
	ret = 1;
	else
	printf("SPI Device: %s 0x%02X (%s) 0x%02X 0x%02X\n"
	"Parameters: num sectors = %i, sector size = %i, write size = %i\n"
	"Flash Size: %i mbit (%i mbyte)\n"
	"Status: 0x%02X\n",
	flash.flash->name, flash.manufacturer_id, flash.manufacturer->name,
	flash.device_id1, flash.device_id2, flash.num_sectors,
	flash.sector_size, flash.write_length,
	(flash.num_sectors * flash.sector_size) >> 17,
	(flash.num_sectors * flash.sector_size) >> 20,
	read_status_register());

	SPI_DEINIT();

	return ret;
	}

	#endif