blob: 0deb1499307306e1e0449ed35c907d4219aec426 [file] [log] [blame]
/*
* (C) Copyright 2007
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* based on work by Anne Sophie Harnois <anne-sophie.harnois@nextream.fr>
*
* (C) Copyright 2001
* Bill Hunter, Wave 7 Optics, williamhunter@mediaone.net
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <ppc4xx.h>
#include <4xx_i2c.h>
#include <i2c.h>
#include <asm-ppc/io.h>
#ifdef CONFIG_HARD_I2C
DECLARE_GLOBAL_DATA_PTR;
#if defined(CONFIG_I2C_MULTI_BUS)
/* Initialize the bus pointer to whatever one the SPD EEPROM is on.
* Default is bus 0. This is necessary because the DDR initialization
* runs from ROM, and we can't switch buses because we can't modify
* the global variables.
*/
#ifdef CONFIG_SYS_SPD_BUS_NUM
static unsigned int i2c_bus_num __attribute__ ((section ("data"))) = CONFIG_SYS_SPD_BUS_NUM;
#else
static unsigned int i2c_bus_num __attribute__ ((section ("data"))) = 0;
#endif
#endif /* CONFIG_I2C_MULTI_BUS */
static void _i2c_bus_reset(void)
{
int i;
u8 dc;
/* Reset status register */
/* write 1 in SCMP and IRQA to clear these fields */
out_8((u8 *)IIC_STS, 0x0A);
/* write 1 in IRQP IRQD LA ICT XFRA to clear these fields */
out_8((u8 *)IIC_EXTSTS, 0x8F);
/* Place chip in the reset state */
out_8((u8 *)IIC_XTCNTLSS, IIC_XTCNTLSS_SRST);
/* Check if bus is free */
dc = in_8((u8 *)IIC_DIRECTCNTL);
if (!DIRCTNL_FREE(dc)){
/* Try to set bus free state */
out_8((u8 *)IIC_DIRECTCNTL, IIC_DIRCNTL_SDAC | IIC_DIRCNTL_SCC);
/* Wait until we regain bus control */
for (i = 0; i < 100; ++i) {
dc = in_8((u8 *)IIC_DIRECTCNTL);
if (DIRCTNL_FREE(dc))
break;
/* Toggle SCL line */
dc ^= IIC_DIRCNTL_SCC;
out_8((u8 *)IIC_DIRECTCNTL, dc);
udelay(10);
dc ^= IIC_DIRCNTL_SCC;
out_8((u8 *)IIC_DIRECTCNTL, dc);
}
}
/* Remove reset */
out_8((u8 *)IIC_XTCNTLSS, 0);
}
void i2c_init(int speed, int slaveadd)
{
unsigned long freqOPB;
int val, divisor;
int bus;
#ifdef CONFIG_SYS_I2C_INIT_BOARD
/* call board specific i2c bus reset routine before accessing the */
/* environment, which might be in a chip on that bus. For details */
/* about this problem see doc/I2C_Edge_Conditions. */
i2c_init_board();
#endif
for (bus = 0; bus < CONFIG_SYS_MAX_I2C_BUS; bus++) {
I2C_SET_BUS(bus);
/* Handle possible failed I2C state */
/* FIXME: put this into i2c_init_board()? */
_i2c_bus_reset();
/* clear lo master address */
out_8((u8 *)IIC_LMADR, 0);
/* clear hi master address */
out_8((u8 *)IIC_HMADR, 0);
/* clear lo slave address */
out_8((u8 *)IIC_LSADR, 0);
/* clear hi slave address */
out_8((u8 *)IIC_HSADR, 0);
/* Clock divide Register */
/* get OPB frequency */
freqOPB = get_OPB_freq();
/* set divisor according to freqOPB */
divisor = (freqOPB - 1) / 10000000;
if (divisor == 0)
divisor = 1;
out_8((u8 *)IIC_CLKDIV, divisor);
/* no interrupts */
out_8((u8 *)IIC_INTRMSK, 0);
/* clear transfer count */
out_8((u8 *)IIC_XFRCNT, 0);
/* clear extended control & stat */
/* write 1 in SRC SRS SWC SWS to clear these fields */
out_8((u8 *)IIC_XTCNTLSS, 0xF0);
/* Mode Control Register
Flush Slave/Master data buffer */
out_8((u8 *)IIC_MDCNTL, IIC_MDCNTL_FSDB | IIC_MDCNTL_FMDB);
val = in_8((u8 *)IIC_MDCNTL);
/* Ignore General Call, slave transfers are ignored,
* disable interrupts, exit unknown bus state, enable hold
* SCL 100kHz normaly or FastMode for 400kHz and above
*/
val |= IIC_MDCNTL_EUBS|IIC_MDCNTL_HSCL;
if (speed >= 400000)
val |= IIC_MDCNTL_FSM;
out_8((u8 *)IIC_MDCNTL, val);
/* clear control reg */
out_8((u8 *)IIC_CNTL, 0x00);
}
/* set to SPD bus as default bus upon powerup */
I2C_SET_BUS(CONFIG_SYS_SPD_BUS_NUM);
}
/*
* This code tries to use the features of the 405GP i2c
* controller. It will transfer up to 4 bytes in one pass
* on the loop. It only does out_8((u8 *)lbz) to the buffer when it
* is possible to do out16(lhz) transfers.
*
* cmd_type is 0 for write 1 for read.
*
* addr_len can take any value from 0-255, it is only limited
* by the char, we could make it larger if needed. If it is
* 0 we skip the address write cycle.
*
* Typical case is a Write of an addr followd by a Read. The
* IBM FAQ does not cover this. On the last byte of the write
* we don't set the creg CHT bit, and on the first bytes of the
* read we set the RPST bit.
*
* It does not support address only transfers, there must be
* a data part. If you want to write the address yourself, put
* it in the data pointer.
*
* It does not support transfer to/from address 0.
*
* It does not check XFRCNT.
*/
static int i2c_transfer(unsigned char cmd_type,
unsigned char chip,
unsigned char addr[],
unsigned char addr_len,
unsigned char data[],
unsigned short data_len)
{
unsigned char* ptr;
int reading;
int tran,cnt;
int result;
int status;
int i;
uchar creg;
if (data == 0 || data_len == 0) {
/* Don't support data transfer of no length or to address 0 */
printf( "i2c_transfer: bad call\n" );
return IIC_NOK;
}
if (addr && addr_len) {
ptr = addr;
cnt = addr_len;
reading = 0;
} else {
ptr = data;
cnt = data_len;
reading = cmd_type;
}
/* Clear Stop Complete Bit */
out_8((u8 *)IIC_STS, IIC_STS_SCMP);
/* Check init */
i = 10;
do {
/* Get status */
status = in_8((u8 *)IIC_STS);
i--;
} while ((status & IIC_STS_PT) && (i > 0));
if (status & IIC_STS_PT) {
result = IIC_NOK_TOUT;
return(result);
}
/* flush the Master/Slave Databuffers */
out_8((u8 *)IIC_MDCNTL, ((in_8((u8 *)IIC_MDCNTL))|IIC_MDCNTL_FMDB|IIC_MDCNTL_FSDB));
/* need to wait 4 OPB clocks? code below should take that long */
/* 7-bit adressing */
out_8((u8 *)IIC_HMADR, 0);
out_8((u8 *)IIC_LMADR, chip);
tran = 0;
result = IIC_OK;
creg = 0;
while (tran != cnt && (result == IIC_OK)) {
int bc,j;
/* Control register =
* Normal transfer, 7-bits adressing, Transfer up to bc bytes, Normal start,
* Transfer is a sequence of transfers
*/
creg |= IIC_CNTL_PT;
bc = (cnt - tran) > 4 ? 4 : cnt - tran;
creg |= (bc - 1) << 4;
/* if the real cmd type is write continue trans */
if ((!cmd_type && (ptr == addr)) || ((tran + bc) != cnt))
creg |= IIC_CNTL_CHT;
if (reading)
creg |= IIC_CNTL_READ;
else
for(j=0; j < bc; j++)
/* Set buffer */
out_8((u8 *)IIC_MDBUF, ptr[tran+j]);
out_8((u8 *)IIC_CNTL, creg);
/* Transfer is in progress
* we have to wait for upto 5 bytes of data
* 1 byte chip address+r/w bit then bc bytes
* of data.
* udelay(10) is 1 bit time at 100khz
* Doubled for slop. 20 is too small.
*/
i = 2*5*8;
do {
/* Get status */
status = in_8((u8 *)IIC_STS);
udelay(10);
i--;
} while ((status & IIC_STS_PT) && !(status & IIC_STS_ERR) && (i > 0));
if (status & IIC_STS_ERR) {
result = IIC_NOK;
status = in_8((u8 *)IIC_EXTSTS);
/* Lost arbitration? */
if (status & IIC_EXTSTS_LA)
result = IIC_NOK_LA;
/* Incomplete transfer? */
if (status & IIC_EXTSTS_ICT)
result = IIC_NOK_ICT;
/* Transfer aborted? */
if (status & IIC_EXTSTS_XFRA)
result = IIC_NOK_XFRA;
} else if ( status & IIC_STS_PT) {
result = IIC_NOK_TOUT;
}
/* Command is reading => get buffer */
if ((reading) && (result == IIC_OK)) {
/* Are there data in buffer */
if (status & IIC_STS_MDBS) {
/*
* even if we have data we have to wait 4OPB clocks
* for it to hit the front of the FIFO, after that
* we can just read. We should check XFCNT here and
* if the FIFO is full there is no need to wait.
*/
udelay(1);
for (j=0; j<bc; j++)
ptr[tran+j] = in_8((u8 *)IIC_MDBUF);
} else
result = IIC_NOK_DATA;
}
creg = 0;
tran += bc;
if (ptr == addr && tran == cnt) {
ptr = data;
cnt = data_len;
tran = 0;
reading = cmd_type;
if (reading)
creg = IIC_CNTL_RPST;
}
}
return (result);
}
int i2c_probe(uchar chip)
{
uchar buf[1];
buf[0] = 0;
/*
* What is needed is to send the chip address and verify that the
* address was <ACK>ed (i.e. there was a chip at that address which
* drove the data line low).
*/
return (i2c_transfer(1, chip << 1, 0,0, buf, 1) != 0);
}
int i2c_read(uchar chip, uint addr, int alen, uchar * buffer, int len)
{
uchar xaddr[4];
int ret;
if (alen > 4) {
printf ("I2C read: addr len %d not supported\n", alen);
return 1;
}
if (alen > 0) {
xaddr[0] = (addr >> 24) & 0xFF;
xaddr[1] = (addr >> 16) & 0xFF;
xaddr[2] = (addr >> 8) & 0xFF;
xaddr[3] = addr & 0xFF;
}
#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
/*
* EEPROM chips that implement "address overflow" are ones
* like Catalyst 24WC04/08/16 which has 9/10/11 bits of
* address and the extra bits end up in the "chip address"
* bit slots. This makes a 24WC08 (1Kbyte) chip look like
* four 256 byte chips.
*
* Note that we consider the length of the address field to
* still be one byte because the extra address bits are
* hidden in the chip address.
*/
if (alen > 0)
chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
#endif
if ((ret = i2c_transfer(1, chip<<1, &xaddr[4-alen], alen, buffer, len)) != 0) {
if (gd->have_console)
printf( "I2c read: failed %d\n", ret);
return 1;
}
return 0;
}
int i2c_write(uchar chip, uint addr, int alen, uchar * buffer, int len)
{
uchar xaddr[4];
if (alen > 4) {
printf ("I2C write: addr len %d not supported\n", alen);
return 1;
}
if (alen > 0) {
xaddr[0] = (addr >> 24) & 0xFF;
xaddr[1] = (addr >> 16) & 0xFF;
xaddr[2] = (addr >> 8) & 0xFF;
xaddr[3] = addr & 0xFF;
}
#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
/*
* EEPROM chips that implement "address overflow" are ones
* like Catalyst 24WC04/08/16 which has 9/10/11 bits of
* address and the extra bits end up in the "chip address"
* bit slots. This makes a 24WC08 (1Kbyte) chip look like
* four 256 byte chips.
*
* Note that we consider the length of the address field to
* still be one byte because the extra address bits are
* hidden in the chip address.
*/
if (alen > 0)
chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
#endif
return (i2c_transfer(0, chip<<1, &xaddr[4-alen], alen, buffer, len ) != 0);
}
/*-----------------------------------------------------------------------
* Read a register
*/
uchar i2c_reg_read(uchar i2c_addr, uchar reg)
{
uchar buf;
i2c_read(i2c_addr, reg, 1, &buf, 1);
return (buf);
}
/*-----------------------------------------------------------------------
* Write a register
*/
void i2c_reg_write(uchar i2c_addr, uchar reg, uchar val)
{
i2c_write(i2c_addr, reg, 1, &val, 1);
}
#if defined(CONFIG_I2C_MULTI_BUS)
/*
* Functions for multiple I2C bus handling
*/
unsigned int i2c_get_bus_num(void)
{
return i2c_bus_num;
}
int i2c_set_bus_num(unsigned int bus)
{
if (bus >= CONFIG_SYS_MAX_I2C_BUS)
return -1;
i2c_bus_num = bus;
return 0;
}
#endif /* CONFIG_I2C_MULTI_BUS */
/* TODO: add 100/400k switching */
unsigned int i2c_get_bus_speed(void)
{
return CONFIG_SYS_I2C_SPEED;
}
int i2c_set_bus_speed(unsigned int speed)
{
if (speed != CONFIG_SYS_I2C_SPEED)
return -1;
return 0;
}
#endif /* CONFIG_HARD_I2C */