blob: 6c2b43c0c59925f0c4d88ad15d639d7a875b0729 [file] [log] [blame]
/*
* Copyright 2008 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* Version 2 as published by the Free Software Foundation.
*/
#include <common.h>
#include <asm/fsl_ddr_sdram.h>
#include "ddr.h"
/* Board-specific functions defined in each board's ddr.c */
extern void fsl_ddr_board_options(memctl_options_t *popts,
unsigned int ctrl_num);
unsigned int populate_memctl_options(int all_DIMMs_registered,
memctl_options_t *popts,
unsigned int ctrl_num)
{
unsigned int i;
/* Chip select options. */
/* Pick chip-select local options. */
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
/* If not DDR2, odt_rd_cfg and odt_wr_cfg need to be 0. */
/* only for single CS? */
popts->cs_local_opts[i].odt_rd_cfg = 0;
popts->cs_local_opts[i].odt_wr_cfg = 1;
popts->cs_local_opts[i].auto_precharge = 0;
}
/* Pick interleaving mode. */
/*
* 0 = no interleaving
* 1 = interleaving between 2 controllers
*/
popts->memctl_interleaving = 0;
/*
* 0 = cacheline
* 1 = page
* 2 = (logical) bank
* 3 = superbank (only if CS interleaving is enabled)
*/
popts->memctl_interleaving_mode = 0;
/*
* 0: cacheline: bit 30 of the 36-bit physical addr selects the memctl
* 1: page: bit to the left of the column bits selects the memctl
* 2: bank: bit to the left of the bank bits selects the memctl
* 3: superbank: bit to the left of the chip select selects the memctl
*
* NOTE: ba_intlv (rank interleaving) is independent of memory
* controller interleaving; it is only within a memory controller.
* Must use superbank interleaving if rank interleaving is used and
* memory controller interleaving is enabled.
*/
/*
* 0 = no
* 0x40 = CS0,CS1
* 0x20 = CS2,CS3
* 0x60 = CS0,CS1 + CS2,CS3
* 0x04 = CS0,CS1,CS2,CS3
*/
popts->ba_intlv_ctl = 0;
/* Memory Organization Parameters */
popts->registered_dimm_en = all_DIMMs_registered;
/* Operational Mode Paramters */
/* Pick ECC modes */
#ifdef CONFIG_DDR_ECC
popts->ECC_mode = 1; /* 0 = disabled, 1 = enabled */
#else
popts->ECC_mode = 0; /* 0 = disabled, 1 = enabled */
#endif
popts->ECC_init_using_memctl = 1; /* 0 = use DMA, 1 = use memctl */
/*
* Choose DQS config
* 0 for DDR1
* 1 for DDR2
*/
#if defined(CONFIG_FSL_DDR1)
popts->DQS_config = 0;
#elif defined(CONFIG_FSL_DDR2)
popts->DQS_config = 1;
#else
#error "Fix DQS for DDR3"
#endif
/* Choose self-refresh during sleep. */
popts->self_refresh_in_sleep = 1;
/* Choose dynamic power management mode. */
popts->dynamic_power = 0;
/* 0 = 64-bit, 1 = 32-bit, 2 = 16-bit */
popts->data_bus_width = 0;
/* Choose burst length. */
popts->burst_length = 4; /* has to be 4 for DDR2 */
/* Global Timing Parameters. */
debug("mclk_ps = %u ps\n", get_memory_clk_period_ps());
/* Pick a caslat override. */
popts->cas_latency_override = 0;
popts->cas_latency_override_value = 3;
if (popts->cas_latency_override) {
debug("using caslat override value = %u\n",
popts->cas_latency_override_value);
}
/* Decide whether to use the computed derated latency */
popts->use_derated_caslat = 0;
/* Choose an additive latency. */
popts->additive_latency_override = 0;
popts->additive_latency_override_value = 3;
if (popts->additive_latency_override) {
debug("using additive latency override value = %u\n",
popts->additive_latency_override_value);
}
/*
* 2T_EN setting
*
* Factors to consider for 2T_EN:
* - number of DIMMs installed
* - number of components, number of active ranks
* - how much time you want to spend playing around
*/
popts->twoT_en = 1;
popts->threeT_en = 0;
/*
* BSTTOPRE precharge interval
*
* Set this to 0 for global auto precharge
*
* FIXME: Should this be configured in picoseconds?
* Why it should be in ps: better understanding of this
* relative to actual DRAM timing parameters such as tRAS.
* e.g. tRAS(min) = 40 ns
*/
popts->bstopre = 0x100;
/* Minimum CKE pulse width -- tCKE(MIN) */
popts->tCKE_clock_pulse_width_ps
= mclk_to_picos(FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR);
/*
* Window for four activates -- tFAW
*
* FIXME: UM: applies only to DDR2/DDR3 with eight logical banks only
* FIXME: varies depending upon number of column addresses or data
* FIXME: width, was considering looking at pdimm->primary_sdram_width
*/
#if defined(CONFIG_FSL_DDR1)
popts->tFAW_window_four_activates_ps = mclk_to_picos(1);
#elif defined(CONFIG_FSL_DDR2)
/*
* x4/x8; some datasheets have 35000
* x16 wide columns only? Use 50000?
*/
popts->tFAW_window_four_activates_ps = 37500;
#elif defined(CONFIG_FSL_DDR3)
#error "FIXME determine four activates for DDR3"
#endif
/* ODT should only be used for DDR2 */
/* FIXME? */
/*
* Interleaving checks.
*
* If memory controller interleaving is enabled, then the data
* bus widths must be programmed identically for the 2 memory
* controllers.
*/
fsl_ddr_board_options(popts, ctrl_num);
return 0;
}