board/vpac270/vpac270.c

/*
 * Voipac PXA270 Support
 *
 * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

#include <common.h>
#include <asm/arch/hardware.h>
#include <netdev.h>
#include <serial.h>
#include <asm/io.h>

DECLARE_GLOBAL_DATA_PTR;

/*
 * Miscelaneous platform dependent initialisations
 */
int board_init(void)
{
	/* memory and cpu-speed are setup before relocation */
	/* so we do _nothing_ here */

	/* Arch number of vpac270 */
	gd->bd->bi_arch_number = MACH_TYPE_VPAC270;

	/* adress of boot parameters */
	gd->bd->bi_boot_params = 0xa0000100;

	return 0;
}

struct serial_device *default_serial_console(void)
{
	return &serial_ffuart_device;
}


int dram_init(void)
{
	gd->ram_size = PHYS_SDRAM_1_SIZE;
#ifdef	CONFIG_256M_U_BOOT
	gd->ram_size += PHYS_SDRAM_2_SIZE;
#endif
	return 0;
}

void dram_init_banksize(void)
{
	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;

#ifdef	CONFIG_256M_U_BOOT
	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
#endif
}

#ifdef	CONFIG_CMD_USB
int usb_board_init(void)
{
	writel((UHCHR | UHCHR_PCPL | UHCHR_PSPL) &
		~(UHCHR_SSEP0 | UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSE),
		UHCHR);

	writel(readl(UHCHR) | UHCHR_FSBIR, UHCHR);

	while (readl(UHCHR) & UHCHR_FSBIR)
		;

	writel(readl(UHCHR) & ~UHCHR_SSE, UHCHR);
	writel((UHCHIE_UPRIE | UHCHIE_RWIE), UHCHIE);

	/* Clear any OTG Pin Hold */
	if (readl(PSSR) & PSSR_OTGPH)
		writel(readl(PSSR) | PSSR_OTGPH, PSSR);

	writel(readl(UHCRHDA) & ~(0x200), UHCRHDA);
	writel(readl(UHCRHDA) | 0x100, UHCRHDA);

	/* Set port power control mask bits, only 3 ports. */
	writel(readl(UHCRHDB) | (0x7<<17), UHCRHDB);

	/* enable port 2 */
	writel(readl(UP2OCR) | UP2OCR_HXOE | UP2OCR_HXS |
		UP2OCR_DMPDE | UP2OCR_DPPDE, UP2OCR);

	return 0;
}

void usb_board_init_fail(void)
{
	return;
}

void usb_board_stop(void)
{
	writel(readl(UHCHR) | UHCHR_FHR, UHCHR);
	udelay(11);
	writel(readl(UHCHR) & ~UHCHR_FHR, UHCHR);

	writel(readl(UHCCOMS) | 1, UHCCOMS);
	udelay(10);

	writel(readl(CKEN) & ~CKEN10_USBHOST, CKEN);

	return;
}
#endif

#ifdef CONFIG_DRIVER_DM9000
int board_eth_init(bd_t *bis)
{
	return dm9000_initialize(bis);
}
#endif