include/configs/PMC405.h - platform/external/u-boot - Gitiles

 /*
  * (C) Copyright 2001-2004
  * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
  *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  */

 /*
  * board/config.h - configuration options, board specific
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */

 #define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
 #define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
 #define CONFIG_PMC405		1	/* ...on a PMC405 board		*/

 #define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/

 #define CONFIG_SYS_CLK_FREQ	33330000 /* external frequency to pll	*/

 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/

 #undef	CONFIG_BOOTARGS
 #undef	CONFIG_BOOTCOMMAND

 #define CONFIG_PREBOOT                  /* enable preboot variable      */

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/

 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */

 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
 				CFG_CMD_BSP	| \
 				CFG_CMD_PCI	| \
 				CFG_CMD_IRQ	| \
 				CFG_CMD_ELF	| \
 				CFG_CMD_DATE	| \
 				CFG_CMD_JFFS2	| \
 				CFG_CMD_MII	| \
 				CFG_CMD_I2C	| \
 				CFG_CMD_PING	| \
 				CFG_CMD_UNIVERSE | \
 				CFG_CMD_EEPROM  )

 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION

 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>

 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/

 #define CONFIG_RTC_MC146818             /* DS1685 is MC146818 compatible*/
 #define CFG_RTC_REG_BASE_ADDR	 0xF0000500 /* RTC Base Address         */

 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/

 /*
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/

 #undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
 #ifdef	CFG_HUSH_PARSER
 #define CFG_PROMPT_HUSH_PS2	"> "
 #endif

 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/

 #define CFG_DEVICE_NULLDEV	1	/* include nulldev device	*/

 #define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/

 #define CONFIG_AUTO_COMPLETE	1       /* add autocompletion support   */

 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

 #undef	CFG_EXT_SERIAL_CLOCK	       /* no external serial clock used */
 #define CFG_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
 #define CFG_BASE_BAUD	    691200

 /* The following table includes the supported baudrates */
 #define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }

 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */

 #define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */

 #define CONFIG_LOOPW            1       /* enable loopw command         */

 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */

 #define CONFIG_VERSION_VARIABLE 1	/* include version env variable */

 #define CFG_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */

 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
  */
 #define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
 #define PCI_HOST_FORCE  1               /* configure as pci host        */
 #define PCI_HOST_AUTO   2               /* detected via arbiter enable  */

 #define CONFIG_PCI			/* include pci support	        */
 #define CONFIG_PCI_HOST	PCI_HOST_AUTO   /* select pci host function     */
 #define CONFIG_PCI_PNP			/* do pci plug-and-play         */
 					/* resource configuration       */

 #define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */

 #define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/

 #define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/

 #define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
 #define CFG_PCI_SUBSYS_DEVICEID 0x0408  /* PCI Device ID: PMC-405       */
 #define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
 #define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
 #define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
 #define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
 #define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
 #define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
 #define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */

 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define CFG_SDRAM_BASE		0x00000000
 #define CFG_MONITOR_BASE	0xFFFC0000
 #define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
 #define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

 /*-----------------------------------------------------------------------
  * FLASH organization
  */
 #define CFG_FLASH_BASE		0xFE000000
 #define CFG_FLASH_INCREMENT	0x01000000

 #define CFG_FLASH_CFI         1       /* Flash is CFI conformant */
 #define CFG_FLASH_CFI_DRIVER  1       /* Use the common driver */
 #define CFG_FLASH_PROTECTION  1       /* don't use hardware protection        */
 #define CFG_FLASH_USE_BUFFER_WRITE 1  /* use buffered writes (20x faster)     */
 #define CFG_MAX_FLASH_BANKS   2       /* max num of flash banks */
 #define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, CFG_FLASH_BASE + CFG_FLASH_INCREMENT }
 #define CFG_MAX_FLASH_SECT    128     /* max num of sects on one chip */

 #define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */

 /*
  * JFFS2 partitions - second bank contains u-boot
  *
  */
 /* No command line, one static partition, whole device */
 #undef CONFIG_JFFS2_CMDLINE
 #define CONFIG_JFFS2_DEV		"nor0"
 #define CONFIG_JFFS2_PART_SIZE		0x01b00000
 #define CONFIG_JFFS2_PART_OFFSET	0x00400000

 /* mtdparts command line support */
 /* Note: fake mtd_id used, no linux mtd map file */
 /*
 #define CONFIG_JFFS2_CMDLINE
 #define MTDIDS_DEFAULT		"nor0=pmc405-0"
 #define MTDPARTS_DEFAULT	"mtdparts=pmc405-0:-(jffs2)"
 */

 /*-----------------------------------------------------------------------
  * Environment Variable setup
  */
 #define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
 #define CFG_ENV_OFFSET		0x000	/* environment starts at the beginning of the EEPROM */
 #define CFG_ENV_SIZE		0x800	/* 2048 bytes may be used for env vars*/
 				   /* total size of a CAT24WC16 is 2048 bytes */

 #define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
 #define CFG_NVRAM_SIZE		242			/* NVRAM size		*/

 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
 #define CONFIG_HARD_I2C			/* I2c with hardware support */
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CFG_I2C_SLAVE		0x7F

 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
 /* mask of address bits that overflow into the "EEPROM chip address"	*/
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
 #define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
 					/* 16 byte page write mode using*/
 					/* last 4 bits of the address	*/
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE

 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
 #define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
 					/* have only 8kB, 16kB is save here	*/
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
 #endif

 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  */
 #define FLASH0_BA	0xFF000000	    /* FLASH 0 Base Address		*/
 #define FLASH1_BA	0xFE000000	    /* FLASH 1 Base Address		*/
 #define CAN_BA		0xF0000000	    /* CAN Base Address			*/
 #define RTC_BA		0xF0000500	    /* RTC Base Address			*/
 #define CF_BA		0xF0100000	    /* CompactFlash Base Address	*/

 /* Memory Bank 0 (Flash Bank 0) initialization					*/
 #define CFG_EBC_PB0AP	0x92015480
 #define CFG_EBC_PB0CR	FLASH0_BA | 0x9A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit*/

 /* Memory Bank 1 (Flash Bank 1) initialization					*/
 #define CFG_EBC_PB1AP	0x92015480
 #define CFG_EBC_PB1CR	FLASH1_BA | 0x9A000 /* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/

 /* Memory Bank 2 (CAN0, 1, RTC) initialization					*/
 #define CFG_EBC_PB2AP	0x03000440   /* TWT=5,TH=2,CSN=0,OEN=0,WBN=0,WBF=0      */
 #define CFG_EBC_PB2CR	CAN_BA | 0x18000    /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/

 /* Memory Bank 3 (CompactFlash IDE, FPGA internal) initialization		*/
 #define CFG_EBC_PB3AP	0x010059C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
 #define CFG_EBC_PB3CR	CF_BA | 0x1A000	    /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */

 /*-----------------------------------------------------------------------
  * FPGA stuff
  */
 #define CFG_FPGA_XC95XL		1	    /* using Xilinx XC95XL CPLD	     */
 #define CFG_FPGA_MAX_SIZE	32*1024	    /* 32kByte is enough for CPLD    */

 /* FPGA program pin configuration */
 #define CFG_FPGA_PRG		0x04000000  /* JTAG TMS pin (ppc output)     */
 #define CFG_FPGA_CLK		0x02000000  /* JTAG TCK pin (ppc output)     */
 #define CFG_FPGA_DATA		0x01000000  /* JTAG TDO->TDI data pin (ppc output) */
 #define CFG_FPGA_INIT		0x00010000  /* unused (ppc input)	     */
 #define CFG_FPGA_DONE		0x00008000  /* JTAG TDI->TDO pin (ppc input) */

 #define CFG_VXWORKS_MAC_PTR	0x00000000	/* Pass Ethernet MAC to VxWorks */

 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in data cache)
  */

 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
 #define CFG_TEMP_STACK_OCM	1

 /* On Chip Memory location */
 #define CFG_OCM_DATA_ADDR	0xF8000000
 #define CFG_OCM_DATA_SIZE	0x1000

 #define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of SDRAM		*/
 #define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET

 /*
  * Internal Definitions
  *
  * Boot Flags
  */
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/

 #endif	/* __CONFIG_H */
	/*
	* (C) Copyright 2001-2004
	* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
	*
	* See file CREDITS for list of people who contributed to this
	* project.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	* MA 02111-1307 USA
	*/

	/*
	* board/config.h - configuration options, board specific
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/

	#define CONFIG_405GP 1 /* This is a PPC405 CPU */
	#define CONFIG_4xx 1 /* ...member of PPC4xx family */
	#define CONFIG_PMC405 1 /* ...on a PMC405 board */

	#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
	#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */

	#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */

	#define CONFIG_BAUDRATE 9600
	#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */

	#undef CONFIG_BOOTARGS
	#undef CONFIG_BOOTCOMMAND

	#define CONFIG_PREBOOT /* enable preboot variable */

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */

	#define CONFIG_MII 1 /* MII PHY management */
	#define CONFIG_PHY_ADDR 0 /* PHY address */
	#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */

	#define CONFIG_COMMANDS ( CONFIG_CMD_DFL \| \
	CFG_CMD_BSP \| \
	CFG_CMD_PCI \| \
	CFG_CMD_IRQ \| \
	CFG_CMD_ELF \| \
	CFG_CMD_DATE \| \
	CFG_CMD_JFFS2 \| \
	CFG_CMD_MII \| \
	CFG_CMD_I2C \| \
	CFG_CMD_PING \| \
	CFG_CMD_UNIVERSE \| \
	CFG_CMD_EEPROM )

	#define CONFIG_MAC_PARTITION
	#define CONFIG_DOS_PARTITION

	/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
	#include <cmd_confdefs.h>

	#undef CONFIG_WATCHDOG /* watchdog disabled */

	#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
	#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */

	#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */

	/*
	* Miscellaneous configurable options
	*/
	#define CFG_LONGHELP /* undef to save memory */
	#define CFG_PROMPT "=> " /* Monitor Command Prompt */

	#undef CFG_HUSH_PARSER /* use "hush" command parser */
	#ifdef CFG_HUSH_PARSER
	#define CFG_PROMPT_HUSH_PS2 "> "
	#endif

	#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
	#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
	#define CFG_MAXARGS 16 /* max number of command args */
	#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */

	#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */

	#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/

	#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */

	#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
	#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */

	#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
	#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
	#define CFG_BASE_BAUD 691200

	/* The following table includes the supported baudrates */
	#define CFG_BAUDRATE_TABLE \
	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
	57600, 115200, 230400, 460800, 921600 }

	#define CFG_LOAD_ADDR 0x100000 /* default load address */
	#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */

	#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */

	#define CONFIG_LOOPW 1 /* enable loopw command */

	#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */

	#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */

	#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */

	/*-----------------------------------------------------------------------
	* PCI stuff
	*-----------------------------------------------------------------------
	*/
	#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
	#define PCI_HOST_FORCE 1 /* configure as pci host */
	#define PCI_HOST_AUTO 2 /* detected via arbiter enable */

	#define CONFIG_PCI /* include pci support */
	#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
	#define CONFIG_PCI_PNP /* do pci plug-and-play */
	/* resource configuration */

	#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */

	#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/

	#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/

	#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
	#define CFG_PCI_SUBSYS_DEVICEID 0x0408 /* PCI Device ID: PMC-405 */
	#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
	#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
	#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
	#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
	#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
	#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
	#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */

	/*-----------------------------------------------------------------------
	* Start addresses for the final memory configuration
	* (Set up by the startup code)
	* Please note that CFG_SDRAM_BASE _must_ start at 0
	*/
	#define CFG_SDRAM_BASE 0x00000000
	#define CFG_MONITOR_BASE 0xFFFC0000
	#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
	#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	/*-----------------------------------------------------------------------
	* FLASH organization
	*/
	#define CFG_FLASH_BASE 0xFE000000
	#define CFG_FLASH_INCREMENT 0x01000000

	#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
	#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
	#define CFG_FLASH_PROTECTION 1 /* don't use hardware protection */
	#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
	#define CFG_MAX_FLASH_BANKS 2 /* max num of flash banks */
	#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, CFG_FLASH_BASE + CFG_FLASH_INCREMENT }
	#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */

	#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */

	/*
	* JFFS2 partitions - second bank contains u-boot
	*
	*/
	/* No command line, one static partition, whole device */
	#undef CONFIG_JFFS2_CMDLINE
	#define CONFIG_JFFS2_DEV "nor0"
	#define CONFIG_JFFS2_PART_SIZE 0x01b00000
	#define CONFIG_JFFS2_PART_OFFSET 0x00400000

	/* mtdparts command line support */
	/* Note: fake mtd_id used, no linux mtd map file */
	/*
	#define CONFIG_JFFS2_CMDLINE
	#define MTDIDS_DEFAULT "nor0=pmc405-0"
	#define MTDPARTS_DEFAULT "mtdparts=pmc405-0:-(jffs2)"
	*/

	/*-----------------------------------------------------------------------
	* Environment Variable setup
	*/
	#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
	#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
	#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
	/* total size of a CAT24WC16 is 2048 bytes */

	#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
	#define CFG_NVRAM_SIZE 242 /* NVRAM size */

	/*-----------------------------------------------------------------------
	* I2C EEPROM (CAT24WC16) for environment
	*/
	#define CONFIG_HARD_I2C /* I2c with hardware support */
	#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
	#define CFG_I2C_SLAVE 0x7F

	#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
	#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
	/* mask of address bits that overflow into the "EEPROM chip address" */
	#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
	#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
	/* 16 byte page write mode using*/
	/* last 4 bits of the address */
	#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
	#define CFG_EEPROM_PAGE_WRITE_ENABLE

	/*-----------------------------------------------------------------------
	* Cache Configuration
	*/
	#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */
	/* have only 8kB, 16kB is save here */
	#define CFG_CACHELINE_SIZE 32 /* ... */
	#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
	#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
	#endif

	/*-----------------------------------------------------------------------
	* External Bus Controller (EBC) Setup
	*/
	#define FLASH0_BA 0xFF000000 /* FLASH 0 Base Address */
	#define FLASH1_BA 0xFE000000 /* FLASH 1 Base Address */
	#define CAN_BA 0xF0000000 /* CAN Base Address */
	#define RTC_BA 0xF0000500 /* RTC Base Address */
	#define CF_BA 0xF0100000 /* CompactFlash Base Address */

	/* Memory Bank 0 (Flash Bank 0) initialization */
	#define CFG_EBC_PB0AP 0x92015480
	#define CFG_EBC_PB0CR FLASH0_BA \| 0x9A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit*/

	/* Memory Bank 1 (Flash Bank 1) initialization */
	#define CFG_EBC_PB1AP 0x92015480
	#define CFG_EBC_PB1CR FLASH1_BA \| 0x9A000 /* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/

	/* Memory Bank 2 (CAN0, 1, RTC) initialization */
	#define CFG_EBC_PB2AP 0x03000440 /* TWT=5,TH=2,CSN=0,OEN=0,WBN=0,WBF=0 */
	#define CFG_EBC_PB2CR CAN_BA \| 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */

	/* Memory Bank 3 (CompactFlash IDE, FPGA internal) initialization */
	#define CFG_EBC_PB3AP 0x010059C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
	#define CFG_EBC_PB3CR CF_BA \| 0x1A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */

	/*-----------------------------------------------------------------------
	* FPGA stuff
	*/
	#define CFG_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */
	#define CFG_FPGA_MAX_SIZE 321024 / 32kByte is enough for CPLD */

	/* FPGA program pin configuration */
	#define CFG_FPGA_PRG 0x04000000 /* JTAG TMS pin (ppc output) */
	#define CFG_FPGA_CLK 0x02000000 /* JTAG TCK pin (ppc output) */
	#define CFG_FPGA_DATA 0x01000000 /* JTAG TDO->TDI data pin (ppc output) */
	#define CFG_FPGA_INIT 0x00010000 /* unused (ppc input) */
	#define CFG_FPGA_DONE 0x00008000 /* JTAG TDI->TDO pin (ppc input) */

	#define CFG_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */

	/*-----------------------------------------------------------------------
	* Definitions for initial stack pointer and data area (in data cache)
	*/

	/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
	#define CFG_TEMP_STACK_OCM 1

	/* On Chip Memory location */
	#define CFG_OCM_DATA_ADDR 0xF8000000
	#define CFG_OCM_DATA_SIZE 0x1000

	#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */
	#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
	#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
	#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
	#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET

	/*
	* Internal Definitions
	*
	* Boot Flags
	*/
	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	#define BOOTFLAG_WARM 0x02 /* Software reboot */

	#endif /* __CONFIG_H */