| /************************************************************************** |
| Etherboot - BOOTP/TFTP Bootstrap Program |
| Skeleton NIC driver for Etherboot |
| ***************************************************************************/ |
| |
| /* |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2, or (at |
| * your option) any later version. |
| */ |
| |
| /* |
| * This file is a modified version from the Galileo polled mode |
| * network driver for the ethernet contained within the GT64260 |
| * chip. It has been modified to fit into the U-Boot framework, from |
| * the original (etherboot) setup. Also, additional cleanup and features |
| * were added. |
| * |
| * - Josh Huber <huber@mclx.com> |
| */ |
| |
| #include <common.h> |
| #include <malloc.h> |
| #include <galileo/gt64260R.h> |
| #include <galileo/core.h> |
| #include <asm/cache.h> |
| #include <miiphy.h> |
| #include <net.h> |
| #include <netdev.h> |
| |
| #include "eth.h" |
| #include "eth_addrtbl.h" |
| |
| #if defined(CONFIG_CMD_NET) && defined(CONFIG_NET_MULTI) |
| |
| #define GT6426x_ETH_BUF_SIZE 1536 |
| |
| /* if you like verbose output, turn this on! */ |
| #undef DEBUG |
| |
| /* Restart autoneg if we detect link is up on phy init. */ |
| |
| /* |
| * The GT doc's say that after Rst is deasserted, and the PHY |
| * reports autoneg complete, it runs through its autoneg |
| * procedures. This doesn't seem to be the case for MII |
| * PHY's. To work around this check for link up && autoneg |
| * complete when initilizing the port. If they are both set, |
| * then restart PHY autoneg. Of course, it may be something |
| * completly different. |
| */ |
| #ifdef CONFIG_ETHER_PORT_MII |
| # define RESTART_AUTONEG |
| #endif |
| |
| /* do this if you dont want to use snooping */ |
| #define USE_SOFTWARE_CACHE_MANAGEMENT |
| |
| #ifdef USE_SOFTWARE_CACHE_MANAGEMENT |
| #define FLUSH_DCACHE(a,b) if(dcache_status()){clean_dcache_range((u32)(a),(u32)(b));} |
| #define FLUSH_AND_INVALIDATE_DCACHE(a,b) if(dcache_status()){flush_dcache_range((u32)(a),(u32)(b));} |
| #define INVALIDATE_DCACHE(a,b) if(dcache_status()){invalidate_dcache_range((u32)(a),(u32)(b));} |
| #else |
| /* bummer - w/o flush, nothing works, even with snooping - FIXME */ |
| /* #define FLUSH_DCACHE(a,b) */ |
| #define FLUSH_DCACHE(a,b) if(dcache_status()){clean_dcache_range((u32)(a),(u32)(b));} |
| #define FLUSH_AND_INVALIDATE_DCACHE(a,b) |
| #define INVALIDATE_DCACHE(a,b) |
| #endif |
| struct eth_dev_s { |
| eth0_tx_desc_single *eth_tx_desc; |
| eth0_rx_desc_single *eth_rx_desc; |
| char *eth_tx_buffer; |
| char *eth_rx_buffer[NR]; |
| int tdn, rdn; |
| int dev; |
| unsigned int reg_base; |
| }; |
| |
| |
| #ifdef CONFIG_INTEL_LXT97X |
| /* for intel LXT972 */ |
| static const char ether_port_phy_addr[3]={0,1,2}; |
| #else |
| static const char ether_port_phy_addr[3]={4,5,6}; |
| #endif |
| |
| /* MII PHY access routines are common for all i/f, use gal_ent0 */ |
| #define GT6426x_MII_DEVNAME "gal_enet0" |
| |
| int gt6426x_miiphy_read(char *devname, unsigned char phy, |
| unsigned char reg, unsigned short *val); |
| |
| static inline unsigned short |
| miiphy_read_ret(unsigned short phy, unsigned short reg) |
| { |
| unsigned short val; |
| gt6426x_miiphy_read(GT6426x_MII_DEVNAME,phy,reg,&val); |
| return val; |
| } |
| |
| |
| /************************************************************************** |
| RESET - Reset adapter |
| ***************************************************************************/ |
| void |
| gt6426x_eth_reset(void *v) |
| { |
| /* we should do something here... |
| struct eth_device *wp = (struct eth_device *)v; |
| struct eth_dev_s *p = wp->priv; |
| */ |
| |
| printf ("RESET\n"); |
| /* put the card in its initial state */ |
| } |
| |
| static void gt6426x_handle_SMI(struct eth_dev_s *p, unsigned int icr) |
| { |
| #ifdef DEBUG |
| printf("SMI interrupt: "); |
| |
| if(icr&0x20000000) { |
| printf("SMI done\n"); |
| } |
| #endif |
| |
| if(icr&0x10000000) { |
| unsigned int psr; |
| psr=GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + p->reg_base); |
| #ifdef DEBUG |
| printf("PHY state change:\n" |
| " GT:%s:%s:%s:%s\n", |
| psr&1?"100":" 10", |
| psr&8?" Link":"nLink", |
| psr&2?"FD":"HD", |
| psr&4?" FC":"nFC"); |
| |
| #ifdef CONFIG_INTEL_LXT97X /* non-standard mii reg (intel lxt972a) */ |
| { |
| unsigned short mii_11; |
| mii_11=miiphy_read_ret(ether_port_phy_addr[p->dev],0x11); |
| |
| printf(" mii:%s:%s:%s:%s %s:%s %s\n", |
| mii_11&(1<<14)?"100":" 10", |
| mii_11&(1<<10)?" Link":"nLink", |
| mii_11&(1<<9)?"FD":"HD", |
| mii_11&(1<<4)?" FC":"nFC", |
| |
| mii_11&(1<<7)?"ANc":"ANnc", |
| mii_11&(1<<8)?"AN":"Manual", |
| "" |
| ); |
| } |
| #endif /* CONFIG_INTEL_LXT97X */ |
| #endif /* DEBUG */ |
| } |
| } |
| |
| static int |
| gt6426x_eth_receive(struct eth_dev_s *p,unsigned int icr) |
| { |
| int eth_len=0; |
| char *eth_data; |
| |
| eth0_rx_desc_single *rx = &p->eth_rx_desc[(p->rdn)]; |
| |
| INVALIDATE_DCACHE((unsigned int)rx,(unsigned int)(rx+1)); |
| |
| if (rx->command_status & 0x80000000) { |
| return 0; /* No packet received */ |
| } |
| |
| eth_len = (unsigned int) |
| (rx->buff_size_byte_count) & 0x0000ffff; |
| eth_data = (char *) p->eth_rx_buffer[p->rdn]; |
| |
| #ifdef DEBUG |
| if (eth_len) { |
| printf ("%s: Recived %d byte Packet @ 0x%p\n", |
| __FUNCTION__, eth_len, eth_data); |
| } |
| #endif |
| /* |
| * packet is now in: |
| * eth0_rx_buffer[RDN_ETH0]; |
| */ |
| |
| /* let the upper layer handle the packet */ |
| NetReceive ((uchar *)eth_data, eth_len); |
| |
| rx->buff_size_byte_count = GT6426x_ETH_BUF_SIZE<<16; |
| |
| |
| /* GT96100 Owner */ |
| rx->command_status = 0x80000000; |
| |
| FLUSH_DCACHE((unsigned int)rx,(unsigned int)(rx+1)); |
| |
| p->rdn ++; |
| if (p->rdn == NR) {p->rdn = 0;} |
| |
| sync(); |
| |
| /* Start Rx*/ |
| GT_REG_WRITE (ETHERNET0_SDMA_COMMAND_REGISTER + p->reg_base, 0x00000080); |
| |
| #ifdef DEBUG |
| { |
| int i; |
| for (i=0;i<12;i++) { |
| printf(" %02x", eth_data[i]); |
| } |
| } |
| printf(": %d bytes\n", eth_len); |
| #endif |
| INVALIDATE_DCACHE((unsigned int)eth_data, |
| (unsigned int)eth_data+eth_len); |
| return eth_len; |
| } |
| |
| /************************************************************************** |
| POLL - look for an rx frame, handle other conditions |
| ***************************************************************************/ |
| int |
| gt6426x_eth_poll(void *v) |
| { |
| struct eth_device *wp = (struct eth_device *)v; |
| struct eth_dev_s *p = wp->priv; |
| unsigned int icr=GTREGREAD(ETHERNET0_INTERRUPT_CAUSE_REGISTER + p->reg_base); |
| |
| if(icr) { |
| GT_REG_WRITE(ETHERNET0_INTERRUPT_CAUSE_REGISTER +p->reg_base, 0); |
| #ifdef DEBUG |
| printf("poll got ICR %08x\n", icr); |
| #endif |
| /* SMI done or PHY state change*/ |
| if(icr&0x30000000) gt6426x_handle_SMI(p, icr); |
| } |
| /* always process. We aren't using RX interrupts */ |
| return gt6426x_eth_receive(p, icr); |
| } |
| |
| /************************************************************************** |
| TRANSMIT - Transmit a frame |
| ***************************************************************************/ |
| int |
| gt6426x_eth_transmit(void *v, volatile char *p, unsigned int s) |
| { |
| struct eth_device *wp = (struct eth_device *)v; |
| struct eth_dev_s *dev = (struct eth_dev_s *)wp->priv; |
| #ifdef DEBUG |
| unsigned int old_command_stat,old_psr; |
| #endif |
| eth0_tx_desc_single *tx = &dev->eth_tx_desc[dev->tdn]; |
| |
| /* wait for tx to be ready */ |
| INVALIDATE_DCACHE((unsigned int)tx,(unsigned int)(tx+1)); |
| while (tx->command_status & 0x80000000) { |
| int i; |
| for(i=0;i<1000;i++); |
| INVALIDATE_DCACHE((unsigned int)tx,(unsigned int)(tx+1)); |
| } |
| |
| GT_REG_WRITE (ETHERNET0_CURRENT_TX_DESCRIPTOR_POINTER0 + dev->reg_base, |
| (unsigned int)tx); |
| |
| #ifdef DEBUG |
| printf("copying to tx_buffer [%p], length %x, desc = %p\n", |
| dev->eth_tx_buffer, s, dev->eth_tx_desc); |
| #endif |
| memcpy(dev->eth_tx_buffer, (char *) p, s); |
| |
| tx->buff_pointer = (uchar *)dev->eth_tx_buffer; |
| tx->bytecount_reserved = ((__u16)s) << 16; |
| |
| /* 31 - own |
| * 22 - gencrc |
| * 18:16 - pad, last, first */ |
| tx->command_status = (1<<31) | (1<<22) | (7<<16); |
| #if 0 |
| /* FEr #18 */ |
| tx->next_desc = NULL; |
| #else |
| tx->next_desc = |
| (struct eth0_tx_desc_struct *) |
| &dev->eth_tx_desc[(dev->tdn+1)%NT].bytecount_reserved; |
| |
| /* cpu owned */ |
| dev->eth_tx_desc[(dev->tdn+1)%NT].command_status = (7<<16); /* pad, last, first */ |
| #endif |
| |
| #ifdef DEBUG |
| old_command_stat=tx->command_status, |
| old_psr=GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + dev->reg_base); |
| #endif |
| |
| FLUSH_DCACHE((unsigned int)tx, |
| (unsigned int)&dev->eth_tx_desc[(dev->tdn+2)%NT]); |
| |
| FLUSH_DCACHE((unsigned int)dev->eth_tx_buffer,(unsigned int)dev->eth_tx_buffer+s); |
| |
| GT_REG_WRITE(ETHERNET0_SDMA_COMMAND_REGISTER + dev->reg_base, 0x01000000); |
| |
| #ifdef DEBUG |
| { |
| unsigned int command_stat=0; |
| printf("cmd_stat: %08x PSR: %08x\n", old_command_stat, old_psr); |
| /* wait for tx to be ready */ |
| do { |
| unsigned int psr=GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + dev->reg_base); |
| command_stat=tx->command_status; |
| if(command_stat!=old_command_stat || psr !=old_psr) { |
| printf("cmd_stat: %08x PSR: %08x\n", command_stat, psr); |
| old_command_stat = command_stat; |
| old_psr = psr; |
| } |
| /* gt6426x_eth0_poll(); */ |
| } while (command_stat & 0x80000000); |
| |
| printf("sent %d byte frame\n", s); |
| |
| if((command_stat & (3<<15)) == 3) { |
| printf("frame had error (stat=%08x)\n", command_stat); |
| } |
| } |
| #endif |
| return 0; |
| } |
| |
| /************************************************************************** |
| DISABLE - Turn off ethernet interface |
| ***************************************************************************/ |
| void |
| gt6426x_eth_disable(void *v) |
| { |
| struct eth_device *wp = (struct eth_device *)v; |
| struct eth_dev_s *p = (struct eth_dev_s *)wp->priv; |
| |
| GT_REG_WRITE(ETHERNET0_SDMA_COMMAND_REGISTER + p->reg_base, 0x80008000); |
| } |
| |
| /************************************************************************** |
| MII utilities - write: write to an MII register via SMI |
| ***************************************************************************/ |
| int |
| gt6426x_miiphy_write(char *devname, unsigned char phy, |
| unsigned char reg, unsigned short data) |
| { |
| unsigned int temp= (reg<<21) | (phy<<16) | data; |
| |
| while(GTREGREAD(ETHERNET_SMI_REGISTER) & (1<<28)); /* wait for !Busy */ |
| |
| GT_REG_WRITE(ETHERNET_SMI_REGISTER, temp); |
| return 0; |
| } |
| |
| /************************************************************************** |
| MII utilities - read: read from an MII register via SMI |
| ***************************************************************************/ |
| int |
| gt6426x_miiphy_read(char *devname, unsigned char phy, |
| unsigned char reg, unsigned short *val) |
| { |
| unsigned int temp= (reg<<21) | (phy<<16) | 1<<26; |
| |
| while(GTREGREAD(ETHERNET_SMI_REGISTER) & (1<<28)); /* wait for !Busy */ |
| |
| GT_REG_WRITE(ETHERNET_SMI_REGISTER, temp); |
| |
| while(1) { |
| temp=GTREGREAD(ETHERNET_SMI_REGISTER); |
| if(temp & (1<<27)) break; /* wait for ReadValid */ |
| } |
| *val = temp & 0xffff; |
| |
| return 0; |
| } |
| |
| #ifdef DEBUG |
| /************************************************************************** |
| MII utilities - dump mii registers |
| ***************************************************************************/ |
| static void |
| gt6426x_dump_mii(bd_t *bis, unsigned short phy) |
| { |
| printf("mii reg 0 - 3: %04x %04x %04x %04x\n", |
| miiphy_read_ret(phy, 0x0), |
| miiphy_read_ret(phy, 0x1), |
| miiphy_read_ret(phy, 0x2), |
| miiphy_read_ret(phy, 0x3) |
| ); |
| printf(" 4 - 7: %04x %04x %04x %04x\n", |
| miiphy_read_ret(phy, 0x4), |
| miiphy_read_ret(phy, 0x5), |
| miiphy_read_ret(phy, 0x6), |
| miiphy_read_ret(phy, 0x7) |
| ); |
| printf(" 8: %04x\n", |
| miiphy_read_ret(phy, 0x8) |
| ); |
| printf(" 16-19: %04x %04x %04x %04x\n", |
| miiphy_read_ret(phy, 0x10), |
| miiphy_read_ret(phy, 0x11), |
| miiphy_read_ret(phy, 0x12), |
| miiphy_read_ret(phy, 0x13) |
| ); |
| printf(" 20,30: %04x %04x\n", |
| miiphy_read_ret(phy, 20), |
| miiphy_read_ret(phy, 30) |
| ); |
| } |
| #endif |
| |
| #ifdef RESTART_AUTONEG |
| |
| /* If link is up && autoneg compleate, and if |
| * GT and PHY disagree about link capabilitys, |
| * restart autoneg - something screwy with FD/HD |
| * unless we do this. */ |
| static void |
| check_phy_state(struct eth_dev_s *p) |
| { |
| int bmsr = miiphy_read_ret(ether_port_phy_addr[p->dev], PHY_BMSR); |
| int psr = GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + p->reg_base); |
| |
| if ((psr & 1<<3) && (bmsr & PHY_BMSR_LS)) { |
| int nego = miiphy_read_ret(ether_port_phy_addr[p->dev], PHY_ANAR) & |
| miiphy_read_ret(ether_port_phy_addr[p->dev], PHY_ANLPAR); |
| int want; |
| |
| if (nego & PHY_ANLPAR_TXFD) { |
| want = 0x3; |
| printf("MII: 100Base-TX, Full Duplex\n"); |
| } else if (nego & PHY_ANLPAR_TX) { |
| want = 0x1; |
| printf("MII: 100Base-TX, Half Duplex\n"); |
| } else if (nego & PHY_ANLPAR_10FD) { |
| want = 0x2; |
| printf("MII: 10Base-T, Full Duplex\n"); |
| } else if (nego & PHY_ANLPAR_10) { |
| want = 0x0; |
| printf("MII: 10Base-T, Half Duplex\n"); |
| } else { |
| printf("MII: Unknown link-foo! %x\n", nego); |
| return; |
| } |
| |
| if ((psr & 0x3) != want) { |
| printf("MII: GT thinks %x, PHY thinks %x, restarting autoneg..\n", |
| psr & 0x3, want); |
| miiphy_write(GT6426x_MII_DEVNAME,ether_port_phy_addr[p->dev],0, |
| miiphy_read_ret(ether_port_phy_addr[p->dev],0) | (1<<9)); |
| udelay(10000); /* the EVB's GT takes a while to notice phy |
| went down and up */ |
| } |
| } |
| } |
| #endif |
| |
| /************************************************************************** |
| PROBE - Look for an adapter, this routine's visible to the outside |
| ***************************************************************************/ |
| int |
| gt6426x_eth_probe(void *v, bd_t *bis) |
| { |
| struct eth_device *wp = (struct eth_device *)v; |
| struct eth_dev_s *p = (struct eth_dev_s *)wp->priv; |
| int dev = p->dev; |
| unsigned int reg_base = p->reg_base; |
| unsigned long temp; |
| int i; |
| |
| if (( dev < 0 ) || ( dev >= GAL_ETH_DEVS )) |
| { /* This should never happen */ |
| printf("%s: Invalid device %d\n", __FUNCTION__, dev ); |
| return 0; |
| } |
| |
| #ifdef DEBUG |
| printf ("%s: initializing %s\n", __FUNCTION__, wp->name ); |
| printf ("\nCOMM_CONTROL = %08x , COMM_CONF = %08x\n", |
| GTREGREAD(COMM_UNIT_ARBITER_CONTROL), |
| GTREGREAD(COMM_UNIT_ARBITER_CONFIGURATION_REGISTER)); |
| #endif |
| |
| /* clear MIB counters */ |
| for(i=0;i<255; i++) |
| temp=GTREGREAD(ETHERNET0_MIB_COUNTER_BASE + reg_base +i); |
| |
| #ifdef CONFIG_INTEL_LXT97X |
| /* for intel LXT972 */ |
| |
| /* led 1: 0x1=txact |
| led 2: 0xc=link/rxact |
| led 3: 0x2=rxact (N/C) |
| strch: 0,2=30 ms, enable */ |
| miiphy_write(GT6426x_MII_DEVNAME,ether_port_phy_addr[p->dev], 20, 0x1c22); |
| |
| /* 2.7ns port rise time */ |
| /*miiphy_write(ether_port_phy_addr[p->dev], 30, 0x0<<10); */ |
| #else |
| /* already set up in mpsc.c */ |
| /*GT_REG_WRITE(MAIN_ROUTING_REGISTER, 0x7ffe38); / b400 */ |
| |
| /* already set up in sdram_init.S... */ |
| /* MPSC0, MPSC1, RMII */ |
| /*GT_REG_WRITE(SERIAL_PORT_MULTIPLEX, 0x1102); / f010 */ |
| #endif |
| GT_REG_WRITE(ETHERNET_PHY_ADDRESS_REGISTER, |
| ether_port_phy_addr[0] | |
| (ether_port_phy_addr[1]<<5) | |
| (ether_port_phy_addr[2]<<10)); /* 2000 */ |
| |
| /* 13:12 - 10: 4x64bit burst (cache line size = 32 bytes) |
| * 9 - 1: RIFB - interrupt on frame boundaries only |
| * 6:7 - 00: big endian rx and tx |
| * 5:2 - 1111: 15 retries */ |
| GT_REG_WRITE(ETHERNET0_SDMA_CONFIGURATION_REGISTER + reg_base, |
| (2<<12) | (1<<9) | (0xf<<2) ); /* 2440 */ |
| |
| #ifndef USE_SOFTWARE_CACHE_MANAGEMENT |
| /* enable rx/tx desc/buffer cache snoop */ |
| GT_REG_READ(ETHERNET_0_ADDRESS_CONTROL_LOW + dev*0x20, |
| &temp); /* f200 */ |
| temp|= (1<<6)| (1<<14)| (1<<22)| (1<<30); |
| GT_REG_WRITE(ETHERNET_0_ADDRESS_CONTROL_LOW + dev*0x20, |
| temp); |
| #endif |
| |
| /* 31 28 27 24 23 20 19 16 |
| * 0000 0000 0000 0000 [0004] |
| * 15 12 11 8 7 4 3 0 |
| * 1000 1101 0000 0000 [4d00] |
| * 20 - 0=MII 1=RMII |
| * 19 - 0=speed autoneg |
| * 15:14 - framesize 1536 (GT6426x_ETH_BUF_SIZE) |
| * 11 - no force link pass |
| * 10 - 1=disable fctl autoneg |
| * 8 - override prio ?? */ |
| temp = 0x00004d00; |
| #ifndef CONFIG_ETHER_PORT_MII |
| temp |= (1<<20); /* RMII */ |
| #endif |
| /* set En */ |
| GT_REG_WRITE(ETHERNET0_PORT_CONFIGURATION_EXTEND_REGISTER + reg_base, |
| temp); /* 2408 */ |
| |
| /* hardcode E1 also? */ |
| /* -- according to dox, this is safer due to extra pulldowns? */ |
| if (dev<2) { |
| GT_REG_WRITE(ETHERNET0_PORT_CONFIGURATION_EXTEND_REGISTER + (dev+1) * 0x400, |
| temp); /* 2408 */ |
| } |
| |
| /* wake up MAC */ /* 2400 */ |
| GT_REG_READ(ETHERNET0_PORT_CONFIGURATION_REGISTER + reg_base, &temp); |
| temp |= (1<<7); /* enable port */ |
| #ifdef CONFIG_GT_USE_MAC_HASH_TABLE |
| temp |= (1<<12); /* hash size 1/2k */ |
| #else |
| temp |= 1; /* promisc */ |
| #endif |
| GT_REG_WRITE(ETHERNET0_PORT_CONFIGURATION_REGISTER + reg_base, temp); |
| /* 2400 */ |
| |
| #ifdef RESTART_AUTONEG |
| check_phy_state(p); |
| #endif |
| |
| printf("%s: Waiting for link up..\n", wp->name); |
| temp = 10 * 1000; |
| /* wait for link back up */ |
| while(!(GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + reg_base) & 8) |
| && (--temp > 0)){ |
| udelay(1000); /* wait 1 ms */ |
| } |
| if ( temp == 0) { |
| printf("%s: Failed!\n", wp->name); |
| return (0); |
| } |
| |
| printf("%s: OK!\n", wp->name); |
| |
| p->tdn = 0; |
| p->rdn = 0; |
| p->eth_tx_desc[p->tdn].command_status = 0; |
| |
| /* Initialize Rx Side */ |
| for (temp = 0; temp < NR; temp++) { |
| p->eth_rx_desc[temp].buff_pointer = (uchar *)p->eth_rx_buffer[temp]; |
| p->eth_rx_desc[temp].buff_size_byte_count = GT6426x_ETH_BUF_SIZE<<16; |
| |
| /* GT96100 Owner */ |
| p->eth_rx_desc[temp].command_status = 0x80000000; |
| p->eth_rx_desc[temp].next_desc = |
| (struct eth0_rx_desc_struct *) |
| &p->eth_rx_desc[(temp+1)%NR].buff_size_byte_count; |
| } |
| |
| FLUSH_DCACHE((unsigned int)&p->eth_tx_desc[0], |
| (unsigned int)&p->eth_tx_desc[NR]); |
| FLUSH_DCACHE((unsigned int)&p->eth_rx_desc[0], |
| (unsigned int)&p->eth_rx_desc[NR]); |
| |
| GT_REG_WRITE(ETHERNET0_CURRENT_TX_DESCRIPTOR_POINTER0 + reg_base, |
| (unsigned int) p->eth_tx_desc); |
| GT_REG_WRITE(ETHERNET0_FIRST_RX_DESCRIPTOR_POINTER0 + reg_base, |
| (unsigned int) p->eth_rx_desc); |
| GT_REG_WRITE(ETHERNET0_CURRENT_RX_DESCRIPTOR_POINTER0 + reg_base, |
| (unsigned int) p->eth_rx_desc); |
| |
| #ifdef DEBUG |
| printf ("\nRx descriptor pointer is %08x %08x\n", |
| GTREGREAD(ETHERNET0_FIRST_RX_DESCRIPTOR_POINTER0 + reg_base), |
| GTREGREAD(ETHERNET0_CURRENT_RX_DESCRIPTOR_POINTER0 + reg_base)); |
| printf ("\n\n%08x %08x\n", |
| (unsigned int)p->eth_rx_desc,p->eth_rx_desc[0].command_status); |
| |
| printf ("Descriptor dump:\n"); |
| printf ("cmd status: %08x\n",p->eth_rx_desc[0].command_status); |
| printf ("byte_count: %08x\n",p->eth_rx_desc[0].buff_size_byte_count); |
| printf ("buff_ptr: %08x\n",(unsigned int)p->eth_rx_desc[0].buff_pointer); |
| printf ("next_desc: %08x\n\n",(unsigned int)p->eth_rx_desc[0].next_desc); |
| printf ("%08x\n",*(unsigned int *) ((unsigned int)p->eth_rx_desc + 0x0)); |
| printf ("%08x\n",*(unsigned int *) ((unsigned int)p->eth_rx_desc + 0x4)); |
| printf ("%08x\n",*(unsigned int *) ((unsigned int)p->eth_rx_desc + 0x8)); |
| printf ("%08x\n\n", |
| *(unsigned int *) ((unsigned int)p->eth_rx_desc + 0xc)); |
| #endif |
| |
| #ifdef DEBUG |
| gt6426x_dump_mii(bis,ether_port_phy_addr[p->dev]); |
| #endif |
| |
| #ifdef CONFIG_GT_USE_MAC_HASH_TABLE |
| { |
| unsigned int hashtable_base; |
| u8 *b = (u8 *)(wp->enetaddr); |
| u32 macH, macL; |
| |
| /* twist the MAC up into the way the discovery wants it */ |
| macH= (b[0]<<8) | b[1]; |
| macL= (b[2]<<24) | (b[3]<<16) | (b[4]<<8) | b[5]; |
| |
| /* mode 0, size 0x800 */ |
| hashtable_base =initAddressTable(dev,0,1); |
| |
| if(!hashtable_base) { |
| printf("initAddressTable failed\n"); |
| return 0; |
| } |
| |
| addAddressTableEntry(dev, macH, macL, 1, 0); |
| GT_REG_WRITE(ETHERNET0_HASH_TABLE_POINTER_REGISTER + reg_base, |
| hashtable_base); |
| } |
| #endif |
| |
| /* Start Rx*/ |
| GT_REG_WRITE(ETHERNET0_SDMA_COMMAND_REGISTER + reg_base, 0x00000080); |
| printf("%s: gt6426x eth device %d init success \n", wp->name, dev ); |
| return 1; |
| } |
| |
| /* enter all the galileo ethernet devs into MULTI-BOOT */ |
| void |
| gt6426x_eth_initialize(bd_t *bis) |
| { |
| struct eth_device *dev; |
| struct eth_dev_s *p; |
| int devnum, x, temp; |
| char *s, *e, buf[64]; |
| |
| #ifdef DEBUG |
| printf( "\n%s\n", __FUNCTION ); |
| #endif |
| |
| for (devnum = 0; devnum < GAL_ETH_DEVS; devnum++) { |
| dev = calloc(sizeof(*dev), 1); |
| if (!dev) { |
| printf( "%s: gal_enet%d allocation failure, %s\n", |
| __FUNCTION__, devnum, "eth_device structure"); |
| return; |
| } |
| |
| /* must be less than NAMESIZE (16) */ |
| sprintf(dev->name, "gal_enet%d", devnum); |
| |
| #ifdef DEBUG |
| printf( "Initializing %s\n", dev->name ); |
| #endif |
| |
| /* Extract the MAC address from the environment */ |
| switch (devnum) |
| { |
| case 0: s = "ethaddr"; break; |
| #if (GAL_ETH_DEVS > 1) |
| case 1: s = "eth1addr"; break; |
| #endif |
| #if (GAL_ETH_DEVS > 2) |
| case 2: s = "eth2addr"; break; |
| #endif |
| default: /* this should never happen */ |
| printf( "%s: Invalid device number %d\n", |
| __FUNCTION__, devnum ); |
| return; |
| } |
| |
| temp = getenv_f(s, buf, sizeof(buf)); |
| s = (temp > 0) ? buf : NULL; |
| |
| #ifdef DEBUG |
| printf ("Setting MAC %d to %s\n", devnum, s ); |
| #endif |
| for (x = 0; x < 6; ++x) { |
| dev->enetaddr[x] = s ? simple_strtoul(s, &e, 16) : 0; |
| if (s) |
| s = (*e) ? e+1 : e; |
| } |
| |
| dev->init = (void*)gt6426x_eth_probe; |
| dev->halt = (void*)gt6426x_eth_reset; |
| dev->send = (void*)gt6426x_eth_transmit; |
| dev->recv = (void*)gt6426x_eth_poll; |
| |
| p = calloc( sizeof(*p), 1 ); |
| dev->priv = (void*)p; |
| if (!p) |
| { |
| printf( "%s: %s allocation failure, %s\n", |
| __FUNCTION__, dev->name, "Private Device Structure"); |
| free(dev); |
| return; |
| } |
| |
| p->dev = devnum; |
| p->tdn=0; |
| p->rdn=0; |
| p->reg_base = devnum * ETHERNET_PORTS_DIFFERENCE_OFFSETS; |
| |
| p->eth_tx_desc = |
| (eth0_tx_desc_single *) |
| (((unsigned int) malloc(sizeof (eth0_tx_desc_single) * |
| (NT+1)) & 0xfffffff0) + 0x10); |
| if (!p) |
| { |
| printf( "%s: %s allocation failure, %s\n", |
| __FUNCTION__, dev->name, "Tx Descriptor"); |
| free(dev); |
| return; |
| } |
| |
| p->eth_rx_desc = |
| (eth0_rx_desc_single *) |
| (((unsigned int) malloc(sizeof (eth0_rx_desc_single) * |
| (NR+1)) & 0xfffffff0) + 0x10); |
| if (!p->eth_rx_desc) |
| { |
| printf( "%s: %s allocation failure, %s\n", |
| __FUNCTION__, dev->name, "Rx Descriptor"); |
| free(dev); |
| free(p); |
| return; |
| } |
| |
| p->eth_tx_buffer = |
| (char *) (((unsigned int) malloc(GT6426x_ETH_BUF_SIZE) & 0xfffffff0) + 0x10); |
| if (!p->eth_tx_buffer) |
| { |
| printf( "%s: %s allocation failure, %s\n", |
| __FUNCTION__, dev->name, "Tx Bufffer"); |
| free(dev); |
| free(p); |
| free(p->eth_rx_desc); |
| return; |
| } |
| |
| for (temp = 0 ; temp < NR ; temp ++) { |
| p->eth_rx_buffer[temp] = |
| (char *) |
| (((unsigned int) malloc(GT6426x_ETH_BUF_SIZE) & 0xfffffff0) + 0x10); |
| if (!p->eth_rx_buffer[temp]) |
| { |
| printf( "%s: %s allocation failure, %s\n", |
| __FUNCTION__, dev->name, "Rx Buffers"); |
| free(dev); |
| free(p); |
| free(p->eth_tx_buffer); |
| free(p->eth_rx_desc); |
| free(p->eth_tx_desc); |
| while (temp >= 0) |
| free(p->eth_rx_buffer[--temp]); |
| return; |
| } |
| } |
| |
| |
| eth_register(dev); |
| #if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) |
| miiphy_register(dev->name, |
| gt6426x_miiphy_read, gt6426x_miiphy_write); |
| #endif |
| } |
| |
| } |
| #endif |