| /* |
| * Board functions for TI AM335X based pxm2 board |
| * (C) Copyright 2013 Siemens Schweiz AG |
| * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. |
| * |
| * Based on: |
| * u-boot:/board/ti/am335x/board.c |
| * |
| * Board functions for TI AM335X based boards |
| * |
| * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/ |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <common.h> |
| #include <errno.h> |
| #include <spl.h> |
| #include <asm/arch/cpu.h> |
| #include <asm/arch/hardware.h> |
| #include <asm/arch/omap.h> |
| #include <asm/arch/ddr_defs.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/gpio.h> |
| #include <asm/arch/mmc_host_def.h> |
| #include <asm/arch/sys_proto.h> |
| #include "../../../drivers/video/da8xx-fb.h" |
| #include <asm/io.h> |
| #include <asm/emif.h> |
| #include <asm/gpio.h> |
| #include <i2c.h> |
| #include <miiphy.h> |
| #include <cpsw.h> |
| #include <watchdog.h> |
| #include "board.h" |
| #include "../common/factoryset.h" |
| #include "pmic.h" |
| #include <nand.h> |
| #include <bmp_layout.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #ifdef CONFIG_SPL_BUILD |
| static void board_init_ddr(void) |
| { |
| struct emif_regs pxm2_ddr3_emif_reg_data = { |
| .sdram_config = 0x41805332, |
| .sdram_tim1 = 0x666b3c9, |
| .sdram_tim2 = 0x243631ca, |
| .sdram_tim3 = 0x33f, |
| .emif_ddr_phy_ctlr_1 = 0x100005, |
| .zq_config = 0, |
| .ref_ctrl = 0x81a, |
| }; |
| |
| struct ddr_data pxm2_ddr3_data = { |
| .datardsratio0 = 0x81204812, |
| .datawdsratio0 = 0, |
| .datafwsratio0 = 0x8020080, |
| .datawrsratio0 = 0x4010040, |
| }; |
| |
| struct cmd_control pxm2_ddr3_cmd_ctrl_data = { |
| .cmd0csratio = 0x80, |
| .cmd0iclkout = 0, |
| .cmd1csratio = 0x80, |
| .cmd1iclkout = 0, |
| .cmd2csratio = 0x80, |
| .cmd2iclkout = 0, |
| }; |
| |
| const struct ctrl_ioregs ioregs = { |
| .cm0ioctl = DDR_IOCTRL_VAL, |
| .cm1ioctl = DDR_IOCTRL_VAL, |
| .cm2ioctl = DDR_IOCTRL_VAL, |
| .dt0ioctl = DDR_IOCTRL_VAL, |
| .dt1ioctl = DDR_IOCTRL_VAL, |
| }; |
| |
| config_ddr(DDR_PLL_FREQ, &ioregs, &pxm2_ddr3_data, |
| &pxm2_ddr3_cmd_ctrl_data, &pxm2_ddr3_emif_reg_data, 0); |
| } |
| |
| /* |
| * voltage switching for MPU frequency switching. |
| * @module = mpu - 0, core - 1 |
| * @vddx_op_vol_sel = vdd voltage to set |
| */ |
| |
| #define MPU 0 |
| #define CORE 1 |
| |
| int voltage_update(unsigned int module, unsigned char vddx_op_vol_sel) |
| { |
| uchar buf[4]; |
| unsigned int reg_offset; |
| |
| if (module == MPU) |
| reg_offset = PMIC_VDD1_OP_REG; |
| else |
| reg_offset = PMIC_VDD2_OP_REG; |
| |
| /* Select VDDx OP */ |
| if (i2c_read(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) |
| return 1; |
| |
| buf[0] &= ~PMIC_OP_REG_CMD_MASK; |
| |
| if (i2c_write(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) |
| return 1; |
| |
| /* Configure VDDx OP Voltage */ |
| if (i2c_read(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) |
| return 1; |
| |
| buf[0] &= ~PMIC_OP_REG_SEL_MASK; |
| buf[0] |= vddx_op_vol_sel; |
| |
| if (i2c_write(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) |
| return 1; |
| |
| if (i2c_read(PMIC_CTRL_I2C_ADDR, reg_offset, 1, buf, 1)) |
| return 1; |
| |
| if ((buf[0] & PMIC_OP_REG_SEL_MASK) != vddx_op_vol_sel) |
| return 1; |
| |
| return 0; |
| } |
| |
| #define OSC (V_OSCK/1000000) |
| |
| const struct dpll_params dpll_mpu_pxm2 = { |
| 720, OSC-1, 1, -1, -1, -1, -1}; |
| |
| void spl_siemens_board_init(void) |
| { |
| uchar buf[4]; |
| /* |
| * pxm2 PMIC code. All boards currently want an MPU voltage |
| * of 1.2625V and CORE voltage of 1.1375V to operate at |
| * 720MHz. |
| */ |
| if (i2c_probe(PMIC_CTRL_I2C_ADDR)) |
| return; |
| |
| /* VDD1/2 voltage selection register access by control i/f */ |
| if (i2c_read(PMIC_CTRL_I2C_ADDR, PMIC_DEVCTRL_REG, 1, buf, 1)) |
| return; |
| |
| buf[0] |= PMIC_DEVCTRL_REG_SR_CTL_I2C_SEL_CTL_I2C; |
| |
| if (i2c_write(PMIC_CTRL_I2C_ADDR, PMIC_DEVCTRL_REG, 1, buf, 1)) |
| return; |
| |
| /* Frequency switching for OPP 120 */ |
| if (voltage_update(MPU, PMIC_OP_REG_SEL_1_2_6) || |
| voltage_update(CORE, PMIC_OP_REG_SEL_1_1_3)) { |
| printf("voltage update failed\n"); |
| } |
| } |
| #endif /* if def CONFIG_SPL_BUILD */ |
| |
| int read_eeprom(void) |
| { |
| /* nothing ToDo here for this board */ |
| |
| return 0; |
| } |
| |
| #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ |
| (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) |
| static void cpsw_control(int enabled) |
| { |
| /* VTP can be added here */ |
| |
| return; |
| } |
| |
| static struct cpsw_slave_data cpsw_slaves[] = { |
| { |
| .slave_reg_ofs = 0x208, |
| .sliver_reg_ofs = 0xd80, |
| .phy_addr = 0, |
| .phy_if = PHY_INTERFACE_MODE_RMII, |
| }, |
| { |
| .slave_reg_ofs = 0x308, |
| .sliver_reg_ofs = 0xdc0, |
| .phy_addr = 1, |
| .phy_if = PHY_INTERFACE_MODE_RMII, |
| }, |
| }; |
| |
| static struct cpsw_platform_data cpsw_data = { |
| .mdio_base = CPSW_MDIO_BASE, |
| .cpsw_base = CPSW_BASE, |
| .mdio_div = 0xff, |
| .channels = 4, |
| .cpdma_reg_ofs = 0x800, |
| .slaves = 1, |
| .slave_data = cpsw_slaves, |
| .ale_reg_ofs = 0xd00, |
| .ale_entries = 1024, |
| .host_port_reg_ofs = 0x108, |
| .hw_stats_reg_ofs = 0x900, |
| .bd_ram_ofs = 0x2000, |
| .mac_control = (1 << 5), |
| .control = cpsw_control, |
| .host_port_num = 0, |
| .version = CPSW_CTRL_VERSION_2, |
| }; |
| #endif /* #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) */ |
| |
| #if defined(CONFIG_DRIVER_TI_CPSW) || \ |
| (defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)) |
| int board_eth_init(bd_t *bis) |
| { |
| int n = 0; |
| #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ |
| (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) |
| struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; |
| #ifdef CONFIG_FACTORYSET |
| int rv; |
| if (!is_valid_ethaddr(factory_dat.mac)) |
| printf("Error: no valid mac address\n"); |
| else |
| eth_env_set_enetaddr("ethaddr", factory_dat.mac); |
| #endif /* #ifdef CONFIG_FACTORYSET */ |
| |
| /* Set rgmii mode and enable rmii clock to be sourced from chip */ |
| writel(RGMII_MODE_ENABLE | RGMII_INT_DELAY, &cdev->miisel); |
| |
| rv = cpsw_register(&cpsw_data); |
| if (rv < 0) |
| printf("Error %d registering CPSW switch\n", rv); |
| else |
| n += rv; |
| #endif |
| return n; |
| } |
| #endif /* #if defined(CONFIG_DRIVER_TI_CPSW) */ |
| |
| #if defined(CONFIG_VIDEO) && !defined(CONFIG_SPL_BUILD) |
| static struct da8xx_panel lcd_panels[] = { |
| /* AUO G156XW01 V1 */ |
| [0] = { |
| .name = "AUO_G156XW01_V1", |
| .width = 1376, |
| .height = 768, |
| .hfp = 14, |
| .hbp = 64, |
| .hsw = 56, |
| .vfp = 1, |
| .vbp = 28, |
| .vsw = 3, |
| .pxl_clk = 60000000, |
| .invert_pxl_clk = 0, |
| }, |
| /* AUO B101EVN06 V0 */ |
| [1] = { |
| .name = "AUO_B101EVN06_V0", |
| .width = 1280, |
| .height = 800, |
| .hfp = 52, |
| .hbp = 84, |
| .hsw = 36, |
| .vfp = 3, |
| .vbp = 14, |
| .vsw = 6, |
| .pxl_clk = 60000000, |
| .invert_pxl_clk = 0, |
| }, |
| /* |
| * Settings from factoryset |
| * stored in EEPROM |
| */ |
| [2] = { |
| .name = "factoryset", |
| .width = 0, |
| .height = 0, |
| .hfp = 0, |
| .hbp = 0, |
| .hsw = 0, |
| .vfp = 0, |
| .vbp = 0, |
| .vsw = 0, |
| .pxl_clk = 60000000, |
| .invert_pxl_clk = 0, |
| }, |
| }; |
| |
| static const struct display_panel disp_panel = { |
| WVGA, |
| 32, |
| 16, |
| COLOR_ACTIVE, |
| }; |
| |
| static const struct lcd_ctrl_config lcd_cfg = { |
| &disp_panel, |
| .ac_bias = 255, |
| .ac_bias_intrpt = 0, |
| .dma_burst_sz = 16, |
| .bpp = 32, |
| .fdd = 0x80, |
| .tft_alt_mode = 0, |
| .stn_565_mode = 0, |
| .mono_8bit_mode = 0, |
| .invert_line_clock = 1, |
| .invert_frm_clock = 1, |
| .sync_edge = 0, |
| .sync_ctrl = 1, |
| .raster_order = 0, |
| }; |
| |
| static int set_gpio(int gpio, int state) |
| { |
| gpio_request(gpio, "temp"); |
| gpio_direction_output(gpio, state); |
| gpio_set_value(gpio, state); |
| gpio_free(gpio); |
| return 0; |
| } |
| |
| static int enable_backlight(void) |
| { |
| set_gpio(BOARD_LCD_POWER, 1); |
| set_gpio(BOARD_BACK_LIGHT, 1); |
| set_gpio(BOARD_TOUCH_POWER, 1); |
| return 0; |
| } |
| |
| static int enable_pwm(void) |
| { |
| struct pwmss_regs *pwmss = (struct pwmss_regs *)PWMSS0_BASE; |
| struct pwmss_ecap_regs *ecap; |
| int ticks = PWM_TICKS; |
| int duty = PWM_DUTY; |
| |
| ecap = (struct pwmss_ecap_regs *)AM33XX_ECAP0_BASE; |
| /* enable clock */ |
| setbits_le32(&pwmss->clkconfig, ECAP_CLK_EN); |
| /* TimeStam Counter register */ |
| writel(0xdb9, &ecap->tsctr); |
| /* config period */ |
| writel(ticks - 1, &ecap->cap3); |
| writel(ticks - 1, &ecap->cap1); |
| setbits_le16(&ecap->ecctl2, |
| (ECTRL2_MDSL_ECAP | ECTRL2_SYNCOSEL_MASK | 0xd0)); |
| /* config duty */ |
| writel(duty, &ecap->cap2); |
| writel(duty, &ecap->cap4); |
| /* start */ |
| setbits_le16(&ecap->ecctl2, ECTRL2_CTRSTP_FREERUN); |
| return 0; |
| } |
| |
| static struct dpll_regs dpll_lcd_regs = { |
| .cm_clkmode_dpll = CM_WKUP + 0x98, |
| .cm_idlest_dpll = CM_WKUP + 0x48, |
| .cm_clksel_dpll = CM_WKUP + 0x54, |
| }; |
| |
| /* no console on this board */ |
| int board_cfb_skip(void) |
| { |
| return 1; |
| } |
| |
| #define PLL_GET_M(v) ((v >> 8) & 0x7ff) |
| #define PLL_GET_N(v) (v & 0x7f) |
| |
| static int get_clk(struct dpll_regs *dpll_regs) |
| { |
| unsigned int val; |
| unsigned int m, n; |
| int f = 0; |
| |
| val = readl(dpll_regs->cm_clksel_dpll); |
| m = PLL_GET_M(val); |
| n = PLL_GET_N(val); |
| f = (m * V_OSCK) / n; |
| |
| return f; |
| }; |
| |
| int clk_get(int clk) |
| { |
| return get_clk(&dpll_lcd_regs); |
| }; |
| |
| static int conf_disp_pll(int m, int n) |
| { |
| struct cm_perpll *cmper = (struct cm_perpll *)CM_PER; |
| struct cm_dpll *cmdpll = (struct cm_dpll *)CM_DPLL; |
| struct dpll_params dpll_lcd = {m, n, -1, -1, -1, -1, -1}; |
| |
| u32 *const clk_domains[] = { |
| &cmper->lcdclkctrl, |
| 0 |
| }; |
| u32 *const clk_modules_explicit_en[] = { |
| &cmper->lcdclkctrl, |
| &cmper->lcdcclkstctrl, |
| &cmper->epwmss0clkctrl, |
| 0 |
| }; |
| do_enable_clocks(clk_domains, clk_modules_explicit_en, 1); |
| writel(0x0, &cmdpll->clklcdcpixelclk); |
| |
| do_setup_dpll(&dpll_lcd_regs, &dpll_lcd); |
| |
| return 0; |
| } |
| |
| static int board_video_init(void) |
| { |
| conf_disp_pll(24, 1); |
| if (factory_dat.pxm50) |
| da8xx_video_init(&lcd_panels[0], &lcd_cfg, lcd_cfg.bpp); |
| else |
| da8xx_video_init(&lcd_panels[1], &lcd_cfg, lcd_cfg.bpp); |
| |
| enable_pwm(); |
| enable_backlight(); |
| |
| return 0; |
| } |
| #endif |
| |
| #ifdef CONFIG_BOARD_LATE_INIT |
| int board_late_init(void) |
| { |
| int ret; |
| |
| omap_nand_switch_ecc(1, 8); |
| |
| #ifdef CONFIG_FACTORYSET |
| if (factory_dat.asn[0] != 0) { |
| char tmp[2 * MAX_STRING_LENGTH + 2]; |
| |
| if (strncmp((const char *)factory_dat.asn, "PXM50", 5) == 0) |
| factory_dat.pxm50 = 1; |
| else |
| factory_dat.pxm50 = 0; |
| sprintf(tmp, "%s_%s", factory_dat.asn, |
| factory_dat.comp_version); |
| ret = env_set("boardid", tmp); |
| if (ret) |
| printf("error setting board id\n"); |
| } else { |
| factory_dat.pxm50 = 1; |
| ret = env_set("boardid", "PXM50_1.0"); |
| if (ret) |
| printf("error setting board id\n"); |
| } |
| debug("PXM50: %d\n", factory_dat.pxm50); |
| #endif |
| |
| return 0; |
| } |
| #endif |
| |
| #include "../common/board.c" |