| U-Boot port for Texas Instruments Keystone II EVM boards |
| ======================================================== |
| |
| Author: Murali Karicheri <m-karicheri2@ti.com> |
| |
| This README has information on the u-boot port for K2HK, K2E, and K2L EVM boards. |
| Documentation for this board can be found at |
| http://www.advantech.com/Support/TI-EVM/EVMK2HX_sd.aspx |
| https://www.einfochips.com/index.php/partnerships/texas-instruments/k2e-evm.html |
| https://www.einfochips.com/index.php/partnerships/texas-instruments/k2l-evm.html |
| |
| The K2HK board is based on Texas Instruments Keystone2 family of SoCs: K2H, K2K. |
| More details on these SoCs are available at company websites |
| K2K: http://www.ti.com/product/tci6638k2k |
| K2H: http://www.ti.com/product/tci6638k2h |
| |
| The K2E SoC details are available at |
| http://www.ti.com/lit/ds/symlink/66ak2e05.pdf |
| |
| The K2L SoC details are available at |
| http://www.ti.com/lit/ds/symlink/tci6630k2l.pdf |
| |
| Board configuration: |
| ==================== |
| |
| Some of the peripherals that are configured by u-boot |
| +------+-------+-------+-----------+-----------+-------+-------+----+ |
| | |DDR3 |NAND |MSM SRAM |ETH ports |UART |I2C |SPI | |
| +------+-------+-------+-----------+-----------+-------+-------+----+ |
| |K2HK |2 |512MB |6MB |4(2) |2 |3 |3 | |
| |K2E |4 |512MB |2MB |8(2) |2 |3 |3 | |
| |K2L |2 |512MB |2MB |4(2) |4 |3 |3 | |
| +------+-------+-------+-----------+-----------+-------+-------+----+ |
| |
| There are only 2 eth port installed on the boards. |
| |
| There are separate PLLs to drive clocks to Tetris ARM and Peripherals. |
| To bring up SMP Linux on this board, there is a boot monitor |
| code that will be installed in MSMC SRAM. There is command available |
| to install this image from u-boot. |
| |
| The port related files can be found at following folders |
| keystone2 SoC related files: arch/arm/cpu/armv7/keystone/ |
| EVMs board files: board/ti/k2s_evm/ |
| |
| Board configuration files: |
| include/configs/k2hk_evm.h |
| include/configs/k2e_evm.h |
| include/configs/k2l_evm.h |
| |
| As u-boot is migrating to Kconfig there is also board defconfig files |
| configs/k2e_evm_defconfig |
| configs/k2hk_evm_defconfig |
| configs/k2l_evm_defconfig |
| |
| Supported boot modes: |
| - SPI NOR boot |
| - AEMIF NAND boot |
| - UART boot |
| |
| Supported image formats: |
| - u-boot-dtb.bin: for loading and running u-boot-dtb.bin through |
| Texas Instruments code composure studio (CCS) and for UART boot. |
| - u-boot-spi.gph: gpimage for programming SPI NOR flash for SPI NOR boot |
| - MLO: gpimage for programming AEMIF NAND flash for NAND boot |
| |
| Build instructions: |
| =================== |
| Examples for k2hk, for k2e and k2l just replace k2hk prefix accordingly. |
| Don't forget to add ARCH=arm and CROSS_COMPILE. |
| |
| To build u-boot-dtb.bin, u-boot-spi.gph, MLO: |
| >make k2hk_evm_defconfig |
| >make |
| |
| Load and Run U-Boot on keystone EVMs using CCS |
| ========================================= |
| |
| Need Code Composer Studio (CCS) installed on a PC to load and run u-boot-dtb.bin |
| on EVM. See instructions at below link for installing CCS on a Windows PC. |
| http://processors.wiki.ti.com/index.php/MCSDK_UG_Chapter_Getting_Started# |
| Installing_Code_Composer_Studio |
| Use u-boot-dtb.bin from the build folder for loading and running u-boot binary |
| on EVM. Follow instructions at |
| K2HK http://processors.wiki.ti.com/index.php/EVMK2H_Hardware_Setup |
| K2E http://processors.wiki.ti.com/index.php/EVMK2E_Hardware_Setup |
| K2L http://processors.wiki.ti.com/index.php/TCIEVMK2L_Hardware_Setup |
| |
| to configure SW1 dip switch to use "No Boot/JTAG DSP Little Endian Boot Mode" |
| and Power ON the EVM. Follow instructions to connect serial port of EVM to |
| PC and start TeraTerm or Hyper Terminal. |
| |
| Start CCS on a Windows machine and Launch Target |
| configuration as instructed at http://processors.wiki.ti.com/index.php/ |
| MCSDK_UG_Chapter_Exploring#Loading_and_Running_U-Boot_on_EVM_through_CCS. |
| The instructions provided in the above link uses a script for |
| loading the u-boot binary on the target EVM. Instead do the following:- |
| |
| 1. Right click to "Texas Instruments XDS2xx USB Emulator_0/CortexA15_1 core (D |
| is connected: Unknown)" at the debug window (This is created once Target |
| configuration is launched) and select "Connect Target". |
| 2. Once target connect is successful, choose Tools->Load Memory option from the |
| top level menu. At the Load Memory window, choose the file u-boot-dtb.bin |
| through "Browse" button and click "next >" button. In the next window, enter |
| Start address as 0xc001000, choose Type-size "32 bits" and click "Finish" |
| button. |
| 3. Click View -> Registers from the top level menu to view registers window. |
| 4. From Registers, window expand "Core Registers" to view PC. Edit PC value |
| to be 0xc001000. From the "Run" top level menu, select "Free Run" |
| 5. The U-Boot prompt is shown at the Tera Term/ Hyper terminal console as |
| below and type any key to stop autoboot as instructed := |
| |
| U-Boot 2014.04-rc1-00201-gc215b5a (Mar 21 2014 - 12:47:59) |
| |
| I2C: ready |
| Detected SO-DIMM [SQR-SD3T-2G1333SED] |
| DRAM: 1.1 GiB |
| NAND: 512 MiB |
| Net: K2HK_EMAC |
| Warning: K2HK_EMAC using MAC address from net device |
| , K2HK_EMAC1, K2HK_EMAC2, K2HK_EMAC3 |
| Hit any key to stop autoboot: 0 |
| |
| SPI NOR Flash programming instructions |
| ====================================== |
| U-Boot image can be flashed to first 512KB of the NOR flash using following |
| instructions: |
| |
| 1. Start CCS and run U-boot as described above. |
| 2. Suspend Target. Select Run -> Suspend from top level menu |
| CortexA15_1 (Free Running)" |
| 3. Load u-boot-spi.gph binary from build folder on to DDR address 0x87000000 |
| through CCS as described in step 2 of "Load and Run U-Boot on K2HK/K2E/K2L |
| EVM using CCS", but using address 0x87000000. |
| 4. Free Run the target as described earlier (step 4) to get u-boot prompt |
| 5. At the U-Boot console type following to setup u-boot environment variables. |
| setenv addr_uboot 0x87000000 |
| setenv filesize <size in hex of u-boot-spi.gph rounded to hex 0x10000> |
| run burn_uboot_spi |
| Once u-boot prompt is available, Power OFF the EVM. Set the SW1 dip switch |
| to "SPI Little Endian Boot mode" as per instruction at |
| http://processors.wiki.ti.com/index.php/*_Hardware_Setup. |
| 6. Power ON the EVM. The EVM now boots with u-boot image on the NOR flash. |
| |
| AEMIF NAND Flash programming instructions |
| ====================================== |
| U-Boot image can be flashed to first 1024KB of the NAND flash using following |
| instructions: |
| |
| 1. Start CCS and run U-boot as described above. |
| 2. Suspend Target. Select Run -> Suspend from top level menu |
| CortexA15_1 (Free Running)" |
| 3. Load MLO binary from build folder on to DDR address 0x87000000 |
| through CCS as described in step 2 of "Load and Run U-Boot on K2HK EVM |
| using CCS", but using address 0x87000000. |
| 4. Free Run the target as described earlier (step 4) to get u-boot prompt |
| 5. At the U-Boot console type following to setup u-boot environment variables. |
| setenv filesize <size in hex of MLO rounded to hex 0x10000> |
| run burn_uboot_nand |
| Once u-boot prompt is available, Power OFF the EVM. Set the SW1 dip switch |
| to "ARM NAND Boot mode" as per instruction at |
| http://processors.wiki.ti.com/index.php/*_Hardware_Setup. |
| 6. Power ON the EVM. The EVM now boots with u-boot image on the NAND flash. |
| |
| Load and Run U-Boot on keystone EVMs using UART download |
| ======================================================== |
| |
| Open BMC and regular UART terminals. |
| |
| 1. On the regular UART port start xmodem transfer of the u-boot-dtb.bin |
| 2. Using BMC terminal set the ARM-UART bootmode and reboot the EVM |
| BMC> bootmode #4 |
| MBC> reboot |
| 3. When xmodem is complete you should see the u-boot starts on the UART port |