| /* |
| * (C) Copyright 2002 |
| * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net |
| * |
| * (C) Copyright 2002 |
| * Sysgo Real-Time Solutions, GmbH <www.elinos.com> |
| * Marius Groeger <mgroeger@sysgo.de> |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| #define CONFIG_PXA250 1 /* This is an PXA250 CPU */ |
| #define CONFIG_XM250 1 /* on a MicroSys XM250 Board */ |
| #undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ |
| |
| /* we will never enable dcache, because we have to setup MMU first */ |
| #define CONFIG_SYS_NO_DCACHE |
| |
| /* |
| * Size of malloc() pool; this lives below the uppermost 128 KiB which are |
| * used for the RAM copy of the uboot code |
| * |
| */ |
| #define CONFIG_SYS_MALLOC_LEN (256*1024) |
| #define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ |
| |
| /* |
| * Hardware drivers |
| */ |
| #define CONFIG_NET_MULTI |
| #define CONFIG_SMC91111 |
| #define CONFIG_SMC91111_BASE 0x04000300 |
| #undef CONFIG_SMC91111_EXT_PHY |
| #define CONFIG_SMC_USE_32_BIT |
| #undef CONFIG_SHOW_ACTIVITY |
| #define CONFIG_NET_RETRY_COUNT 10 /* # of retries */ |
| |
| /* |
| * I2C bus |
| */ |
| #define CONFIG_HARD_I2C 1 |
| #define CONFIG_SYS_I2C_SPEED 50000 |
| #define CONFIG_SYS_I2C_SLAVE 0xfe |
| |
| #define CONFIG_RTC_PCF8563 1 |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x51 |
| |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 /* A0 = 0 (hardwired) */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 4 bits = 16 octets */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* between stop and start */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* length of address */ |
| #define CONFIG_SYS_EEPROM_SIZE 2048 /* size in bytes */ |
| #undef CONFIG_SYS_I2C_INIT_BOARD /* board has no own init */ |
| |
| /* |
| * select serial console configuration |
| */ |
| #define CONFIG_PXA_SERIAL |
| #define CONFIG_FFUART 1 /* we use FFUART */ |
| |
| /* allow to overwrite serial and ethaddr */ |
| #define CONFIG_ENV_OVERWRITE |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_I2C |
| |
| |
| #define CONFIG_BOOTDELAY 3 |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0xa3000000 /* default load address */ |
| |
| #define CONFIG_SYS_HZ 1000 |
| #define CONFIG_SYS_CPUSPEED 0x161 /* set core clock to 400/400/100 MHz */ |
| |
| /* valid baudrates */ |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } |
| |
| /* |
| * Definitions related to passing arguments to kernel. |
| */ |
| #define CONFIG_CMDLINE_TAG 1 /* send commandline to Kernel */ |
| #define CONFIG_SETUP_MEMORY_TAGS 1 /* send memory definition to kernel */ |
| #define CONFIG_INITRD_TAG 1 /* do not send initrd params */ |
| #undef CONFIG_VFD /* do not send framebuffer setup */ |
| |
| /* |
| * Stack sizes |
| * |
| * The stack sizes are set up in start.S using the settings below |
| */ |
| #define CONFIG_STACKSIZE (128*1024) /* regular stack */ |
| #ifdef CONFIG_USE_IRQ |
| #define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ |
| #define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ |
| #endif |
| |
| /* |
| * Physical Memory Map |
| */ |
| #define CONFIG_NR_DRAM_BANKS 4 |
| #define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */ |
| #define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */ |
| #define PHYS_SDRAM_2 0xa4000000 /* SDRAM Bank #2 */ |
| #define PHYS_SDRAM_2_SIZE 0x00000000 /* 0 MB */ |
| #define PHYS_SDRAM_3 0xa8000000 /* SDRAM Bank #3 */ |
| #define PHYS_SDRAM_3_SIZE 0x00000000 /* 0 MB */ |
| #define PHYS_SDRAM_4 0xac000000 /* SDRAM Bank #4 */ |
| #define PHYS_SDRAM_4_SIZE 0x00000000 /* 0 MB */ |
| |
| #define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ |
| #define PHYS_FLASH_2 0x04000000 /* Flash Bank #1 */ |
| #define PHYS_FLASH_SIZE 0x01000000 /* 16 MB */ |
| #define PHYS_FLASH_BANK_SIZE 0x01000000 /* 16 MB Banks */ |
| #define PHYS_FLASH_SECT_SIZE 0x00040000 /* 256 KB sectors (x2) */ |
| |
| #define CONFIG_SYS_DRAM_BASE 0xa0000000 |
| #define CONFIG_SYS_DRAM_SIZE 0x04000000 |
| |
| #define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 |
| |
| #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 |
| #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_GBL_DATA_SIZE + PHYS_SDRAM_1) |
| |
| /* |
| * FLASH and environment organization |
| */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ |
| |
| /* timeout values are in ticks */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Erase */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Write */ |
| #define CONFIG_SYS_FLASH_LOCK_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Set Lock Bit */ |
| #define CONFIG_SYS_FLASH_UNLOCK_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Clear Lock Bits */ |
| #define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ |
| |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x40000) /* Addr of Environment Sector */ |
| #define CONFIG_ENV_SIZE 0x4000 |
| #define CONFIG_ENV_SECT_SIZE 0x40000 /* Size of the Environment Sector */ |
| #define CONFIG_SYS_MONITOR_LEN 0x20000 /* 128 KiB */ |
| |
| /****************************************************************************** |
| * |
| * CPU specific defines |
| * |
| ******************************************************************************/ |
| |
| /* |
| * GPIO settings |
| * |
| * GPIO pin assignments |
| * GPIO Name Dir Out AF |
| * 0 NC |
| * 1 NC |
| * 2 SIRQ1 I |
| * 3 SIRQ2 I |
| * 4 SIRQ3 I |
| * 5 DMAACK1 O 0 |
| * 6 DMAACK2 O 0 |
| * 7 DMAACK3 O 0 |
| * 8 TC1 O 0 |
| * 9 TC2 O 0 |
| * 10 TC3 O 0 |
| * 11 nDMAEN O 1 |
| * 12 AENCTRL O 0 |
| * 13 PLDTC O 0 |
| * 14 ETHIRQ I |
| * 15 NC |
| * 16 NC |
| * 17 NC |
| * 18 RDY I |
| * 19 DMASIO I |
| * 20 ETHIRQ NC |
| * 21 NC |
| * 22 PGMEN O 1 FIXME for debug only enable flash |
| * 23 NC |
| * 24 NC |
| * 25 NC |
| * 26 NC |
| * 27 NC |
| * 28 NC |
| * 29 NC |
| * 30 NC |
| * 31 NC |
| * 32 NC |
| * 33 NC |
| * 34 FFRXD I 01 |
| * 35 FFCTS I 01 |
| * 36 FFDCD I 01 |
| * 37 FFDSR I 01 |
| * 38 FFRI I 01 |
| * 39 FFTXD O 1 10 |
| * 40 FFDTR O 0 10 |
| * 41 FFRTS O 0 10 |
| * 42 RS232FOFF O 0 00 |
| * 43 NC |
| * 44 NC |
| * 45 IRSL0 O 0 |
| * 46 IRRX0 I 01 |
| * 47 IRTX0 O 0 10 |
| * 48 NC |
| * 49 nIOWE O 0 |
| * 50 NC |
| * 51 NC |
| * 52 NC |
| * 53 NC |
| * 54 NC |
| * 55 NC |
| * 56 NC |
| * 57 NC |
| * 58 DKDIRQ I |
| * 59 NC |
| * 60 NC |
| * 61 NC |
| * 62 NC |
| * 63 NC |
| * 64 COMLED O 0 |
| * 65 COMLED O 0 |
| * 66 COMLED O 0 |
| * 67 COMLED O 0 |
| * 68 COMLED O 0 |
| * 69 COMLED O 0 |
| * 70 COMLED O 0 |
| * 71 COMLED O 0 |
| * 72 NC |
| * 73 NC |
| * 74 NC |
| * 75 NC |
| * 76 NC |
| * 77 NC |
| * 78 CSIO O 1 |
| * 79 NC |
| * 80 CSETH O 1 |
| * |
| * NOTE: All NC's are defined to be outputs |
| * |
| */ |
| /* Pin direction control */ |
| #define CONFIG_SYS_GPDR0_VAL 0xd3808000 |
| #define CONFIG_SYS_GPDR1_VAL 0xfcffab83 |
| #define CONFIG_SYS_GPDR2_VAL 0x0001ffff |
| /* Set and Clear registers */ |
| #define CONFIG_SYS_GPSR0_VAL 0x00008000 |
| #define CONFIG_SYS_GPSR1_VAL 0x00ff0002 |
| #define CONFIG_SYS_GPSR2_VAL 0x0001c000 |
| #define CONFIG_SYS_GPCR0_VAL 0x00000000 |
| #define CONFIG_SYS_GPCR1_VAL 0x00000000 |
| #define CONFIG_SYS_GPCR2_VAL 0x00000000 |
| /* Edge detect registers (these are set by the kernel) */ |
| #define CONFIG_SYS_GRER0_VAL 0x00002180 |
| #define CONFIG_SYS_GRER1_VAL 0x00000000 |
| #define CONFIG_SYS_GRER2_VAL 0x00000000 |
| #define CONFIG_SYS_GFER0_VAL 0x000043e0 |
| #define CONFIG_SYS_GFER1_VAL 0x00000000 |
| #define CONFIG_SYS_GFER2_VAL 0x00000000 |
| /* Alternate function registers */ |
| #define CONFIG_SYS_GAFR0_L_VAL 0x80000004 |
| #define CONFIG_SYS_GAFR0_U_VAL 0x595a8010 |
| #define CONFIG_SYS_GAFR1_L_VAL 0x699a9559 |
| #define CONFIG_SYS_GAFR1_U_VAL 0xaaa5aaaa |
| #define CONFIG_SYS_GAFR2_L_VAL 0xaaaaaaaa |
| #define CONFIG_SYS_GAFR2_U_VAL 0x00000002 |
| |
| /* |
| * Clocks, power control and interrupts |
| */ |
| #define CONFIG_SYS_PSSR_VAL 0x00000030 |
| #define CONFIG_SYS_CCCR_VAL 0x00000161 /* 100 MHz memory, 400 MHz CPU, 400 Turbo */ |
| #define CONFIG_SYS_CKEN_VAL 0x000141ec /* FFUART and STUART enabled */ |
| #define CONFIG_SYS_ICMR_VAL 0x00000000 /* No interrupts enabled */ |
| |
| /* FIXME |
| * |
| * RTC settings |
| * Watchdog |
| * |
| */ |
| |
| /* |
| * Memory settings |
| * |
| */ |
| #define CONFIG_SYS_MSC0_VAL 0x122423f0 /* FLASH / LAN (cs0)/(cS1) */ |
| #define CONFIG_SYS_MSC1_VAL 0x35f4aa4c /* USB / ST3+ST5 (cs2)/(cS3) */ |
| #define CONFIG_SYS_MSC2_VAL 0x35f435fc /* IDE / BCR + WatchDog (cs4)/(cS5) */ |
| #define CONFIG_SYS_MDCNFG_VAL 0x000009c9 |
| #define CONFIG_SYS_MDMRS_VAL 0x00220022 |
| #define CONFIG_SYS_MDREFR_VAL 0x000da018 /* Initial setting, individual bits set in lowlevel_init.S */ |
| |
| /* |
| * PCMCIA and CF Interfaces (NOT USED, these values from lubbock init) |
| */ |
| #define CONFIG_SYS_MECR_VAL 0x00000000 |
| #define CONFIG_SYS_MCMEM0_VAL 0x00010504 |
| #define CONFIG_SYS_MCMEM1_VAL 0x00010504 |
| #define CONFIG_SYS_MCATT0_VAL 0x00010504 |
| #define CONFIG_SYS_MCATT1_VAL 0x00010504 |
| #define CONFIG_SYS_MCIO0_VAL 0x00004715 |
| #define CONFIG_SYS_MCIO1_VAL 0x00004715 |
| |
| /* Board specific defines */ |
| |
| #ifndef __ASSEMBLY__ |
| |
| /* global prototypes */ |
| void led_code(int code, int color); |
| |
| #endif |
| |
| #endif /* __CONFIG_H */ |