| /* |
| * (C) Copyright 2011 Logic Product Development <www.logicpd.com> |
| * Peter Barada <peter.barada@logicpd.com> |
| * |
| * Configuration settings for the Logic OMAP35x/DM37x SOM LV/Torpedo |
| * reference boards. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* High Level Configuration Options */ |
| |
| #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ |
| |
| /* |
| * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM |
| * 64 bytes before this address should be set aside for u-boot.img's |
| * header. That is 0x800FFFC0--0x80100000 should not be used for any |
| * other needs. We use this rather than the inherited defines from |
| * ti_armv7_common.h for backwards compatibility. |
| */ |
| #define CONFIG_SYS_TEXT_BASE 0x80100000 |
| #define CONFIG_SPL_BSS_START_ADDR 0x80000000 |
| #define CONFIG_SPL_BSS_MAX_SIZE (512 << 10) /* 512 KB */ |
| #define CONFIG_SYS_SPL_MALLOC_START 0x80208000 |
| #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 |
| |
| #include <configs/ti_omap3_common.h> |
| |
| /* Override default SPL info to minimize empty space and allow BCH8 in SPL */ |
| #undef CONFIG_SPL_TEXT_BASE |
| #undef CONFIG_SPL_MAX_SIZE |
| #define CONFIG_SPL_TEXT_BASE 0x40200000 |
| #define CONFIG_SPL_MAX_SIZE (64 * 1024) |
| |
| /* Display CPU and Board information */ |
| |
| #define CONFIG_DISPLAY_CPUINFO |
| #define CONFIG_DISPLAY_BOARDINFO |
| #define CONFIG_BOARD_LATE_INIT |
| #define CONFIG_MISC_INIT_R /* misc_init_r dumps the die id */ |
| #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ |
| #define CONFIG_SETUP_MEMORY_TAGS |
| #define CONFIG_INITRD_TAG |
| #define CONFIG_REVISION_TAG |
| #define CONFIG_CMDLINE_EDITING /* cmd line edit/history */ |
| #define CONFIG_ZERO_BOOTDELAY_CHECK /* check keypress w/no delay */ |
| |
| /* Hardware drivers */ |
| |
| /* GPIO banks */ |
| #define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */ |
| |
| #define CONFIG_USB_OMAP3 |
| |
| /* select serial console configuration */ |
| #undef CONFIG_CONS_INDEX |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1 |
| #define CONFIG_SERIAL1 1 /* UART1 on OMAP Logic boards */ |
| |
| /* commands to include */ |
| #define CONFIG_CMD_NAND |
| #define CONFIG_CMD_CACHE |
| #define CONFIG_CMD_EXT2 |
| #define CONFIG_CMD_FAT |
| #define CONFIG_CMD_MTDPARTS |
| #define CONFIG_CMD_NAND_LOCK_UNLOCK /* nand (un)lock commands */ |
| |
| /* I2C */ |
| #define CONFIG_SYS_I2C_OMAP34XX |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C64 */ |
| #define EXPANSION_EEPROM_I2C_BUS 2 /* I2C Bus for AT24C64 */ |
| #define CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID |
| |
| /* USB */ |
| #define CONFIG_USB_MUSB_OMAP2PLUS |
| #define CONFIG_USB_MUSB_PIO_ONLY |
| #define CONFIG_USB_ETHER |
| #define CONFIG_USB_ETHER_RNDIS |
| #define CONFIG_USB_FUNCTION_FASTBOOT |
| #define CONFIG_CMD_FASTBOOT |
| #define CONFIG_ANDROID_BOOT_IMAGE |
| #define CONFIG_FASTBOOT_BUF_ADDR CONFIG_SYS_LOAD_ADDR |
| #define CONFIG_FASTBOOT_BUF_SIZE 0x07000000 |
| #define CONFIG_SYS_CACHELINE_SIZE 64 |
| |
| /* TWL4030 */ |
| #define CONFIG_TWL4030_PWM |
| #define CONFIG_TWL4030_USB |
| |
| /* Board NAND Info. */ |
| #ifdef CONFIG_NAND |
| #define CONFIG_NAND_OMAP_GPMC |
| |
| #define CONFIG_CMD_UBI /* UBI-formated MTD partition support */ |
| #define CONFIG_CMD_UBIFS /* Read-only UBI volume operations */ |
| #define CONFIG_RBTREE /* required by CONFIG_CMD_UBI */ |
| #define CONFIG_LZO /* required by CONFIG_CMD_UBIFS */ |
| |
| #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */ |
| /* to access nand */ |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */ |
| /* NAND devices */ |
| #define CONFIG_SYS_NAND_BUSWIDTH_16BIT |
| #define CONFIG_SYS_NAND_5_ADDR_CYCLE |
| #define CONFIG_SYS_NAND_PAGE_COUNT 64 |
| #define CONFIG_SYS_NAND_PAGE_SIZE 2048 |
| #define CONFIG_SYS_NAND_OOBSIZE 64 |
| #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) |
| #define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS |
| #define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, \ |
| 13, 14, 16, 17, 18, 19, 20, 21, 22, \ |
| 23, 24, 25, 26, 27, 28, 30, 31, 32, \ |
| 33, 34, 35, 36, 37, 38, 39, 40, 41, \ |
| 42, 44, 45, 46, 47, 48, 49, 50, 51, \ |
| 52, 53, 54, 55, 56} |
| |
| #define CONFIG_SYS_NAND_ECCSIZE 512 |
| #define CONFIG_SYS_NAND_ECCBYTES 13 |
| #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |
| #define CONFIG_BCH |
| #define CONFIG_SYS_NAND_MAX_OOBFREE 2 |
| #define CONFIG_SYS_NAND_MAX_ECCPOS 56 |
| #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 |
| #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ |
| #define CONFIG_MTD_PARTITIONS /* required for UBI partition support */ |
| #define MTDIDS_DEFAULT "nand0=omap2-nand.0" |
| #define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(MLO),"\ |
| "1920k(u-boot),128k(u-boot-env),"\ |
| "4m(kernel),-(fs)" |
| #endif |
| |
| /* Environment information */ |
| |
| /* |
| * PREBOOT assumes the 4.3" display is attached. User can interrupt |
| * and modify display variable to suit their needs. |
| */ |
| #define CONFIG_PREBOOT \ |
| "echo ======================NOTICE============================;"\ |
| "echo \"The u-boot environment is not set.\";" \ |
| "echo \"If using a display a valid display varible for your panel\";" \ |
| "echo \"needs to be set.\";" \ |
| "echo \"Valid display options are:\";" \ |
| "echo \" 2 == LQ121S1DG31 TFT SVGA (12.1) Sharp\";" \ |
| "echo \" 3 == LQ036Q1DA01 TFT QVGA (3.6) Sharp w/ASIC\";" \ |
| "echo \" 5 == LQ064D343 TFT VGA (6.4) Sharp\";" \ |
| "echo \" 7 == LQ10D368 TFT VGA (10.4) Sharp\";" \ |
| "echo \" 15 == LQ043T1DG01 TFT WQVGA (4.3) Sharp (DEFAULT)\";" \ |
| "echo \" vga[-dvi or -hdmi] LCD VGA 640x480\";" \ |
| "echo \" svga[-dvi or -hdmi] LCD SVGA 800x600\";" \ |
| "echo \" xga[-dvi or -hdmi] LCD XGA 1024x768\";" \ |
| "echo \" 720p[-dvi or -hdmi] LCD 720P 1280x720\";" \ |
| "echo \"Defaulting to 4.3 LCD panel (display=15).\";" \ |
| "setenv display 15;" \ |
| "setenv preboot;" \ |
| "nand unlock;" \ |
| "saveenv;" |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "loadaddr=0x81000000\0" \ |
| "uimage=uImage\0" \ |
| "zimage=zImage\0" \ |
| "mtdids=" MTDIDS_DEFAULT "\0" \ |
| "mtdparts=" MTDPARTS_DEFAULT "\0" \ |
| "mmcdev=0\0" \ |
| "mmcroot=/dev/mmcblk0p2 rw\0" \ |
| "mmcrootfstype=ext4 rootwait\0" \ |
| "nandroot=ubi0:rootfs rw ubi.mtd=fs noinitrd\0" \ |
| "nandrootfstype=ubifs rootwait\0" \ |
| "autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \ |
| "if run loadbootscript; then " \ |
| "run bootscript; " \ |
| "else " \ |
| "run defaultboot;" \ |
| "fi; " \ |
| "else run defaultboot; fi\0" \ |
| "defaultboot=run mmcramboot\0" \ |
| "consoledevice=ttyO0\0" \ |
| "display=15\0" \ |
| "setconsole=setenv console ${consoledevice},${baudrate}n8\0" \ |
| "dump_bootargs=echo 'Bootargs: '; echo $bootargs\0" \ |
| "rotation=0\0" \ |
| "vrfb_arg=if itest ${rotation} -ne 0; then " \ |
| "setenv bootargs ${bootargs} omapfb.vrfb=y " \ |
| "omapfb.rotate=${rotation}; " \ |
| "fi\0" \ |
| "optargs=ignore_loglevel early_printk no_console_suspend\0" \ |
| "addmtdparts=setenv bootargs ${bootargs} ${mtdparts}\0" \ |
| "common_bootargs=setenv bootargs ${bootargs} display=${display} " \ |
| "${optargs};" \ |
| "run addmtdparts; " \ |
| "run vrfb_arg\0" \ |
| "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ |
| "bootscript=echo 'Running bootscript from mmc ...'; " \ |
| "source ${loadaddr}\0" \ |
| "loaduimage=mmc rescan; " \ |
| "fatload mmc ${mmcdev} ${loadaddr} ${uimage}\0" \ |
| "loadzimage=mmc rescan; " \ |
| "fatload mmc ${mmcdev} ${loadaddr} ${zimage}\0" \ |
| "ramdisksize=64000\0" \ |
| "ramdiskaddr=0x82000000\0" \ |
| "ramdiskimage=rootfs.ext2.gz.uboot\0" \ |
| "loadramdisk=mmc rescan; " \ |
| "fatload mmc ${mmcdev} ${ramdiskaddr} ${ramdiskimage}\0" \ |
| "ramargs=run setconsole; setenv bootargs console=${console} " \ |
| "root=/dev/ram rw ramdisk_size=${ramdisksize}\0" \ |
| "mmcargs=run setconsole; setenv bootargs console=${console} " \ |
| "${optargs} " \ |
| "root=${mmcroot} " \ |
| "rootfstype=${mmcrootfstype}\0" \ |
| "nandargs=run setconsole; setenv bootargs console=${console} " \ |
| "${optargs} " \ |
| "root=${nandroot} " \ |
| "rootfstype=${nandrootfstype}\0" \ |
| "fdtaddr=0x86000000\0" \ |
| "loadfdtimage=mmc rescan; " \ |
| "fatload mmc ${mmcdev} ${fdtaddr} ${fdtimage}\0" \ |
| "mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \ |
| "run mmcargs; " \ |
| "run common_bootargs; " \ |
| "run dump_bootargs; " \ |
| "run loadzimage; " \ |
| "run loadfdtimage; " \ |
| "bootz ${loadaddr} - ${fdtaddr}\0" \ |
| "mmcramboot=echo 'Booting uImage kernel from mmc w/ramdisk...'; " \ |
| "run ramargs; " \ |
| "run common_bootargs; " \ |
| "run dump_bootargs; " \ |
| "run loaduimage; " \ |
| "run loadramdisk; " \ |
| "bootm ${loadaddr} ${ramdiskaddr}\0" \ |
| "mmcrambootz=echo 'Booting zImage kernel from mmc w/ramdisk...'; " \ |
| "run ramargs; " \ |
| "run common_bootargs; " \ |
| "run dump_bootargs; " \ |
| "run loadzimage; " \ |
| "run loadramdisk; " \ |
| "run loadfdtimage; " \ |
| "bootz ${loadaddr} ${ramdiskaddr} ${fdtaddr}\0; " \ |
| "tftpboot=echo 'Booting kernel/ramdisk rootfs from tftp...'; " \ |
| "run ramargs; " \ |
| "run common_bootargs; " \ |
| "run dump_bootargs; " \ |
| "tftpboot ${loadaddr} ${uimage}; " \ |
| "tftpboot ${ramdiskaddr} ${ramdiskimage}; " \ |
| "bootm ${loadaddr} ${ramdiskaddr}\0" |
| |
| #define CONFIG_BOOTCOMMAND \ |
| "run autoboot" |
| |
| /* Miscellaneous configurable options */ |
| #define CONFIG_AUTO_COMPLETE |
| |
| /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) |
| #define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ |
| 0x01F00000) /* 31MB */ |
| |
| /* FLASH and environment organization */ |
| |
| /* **** PISMO SUPPORT *** */ |
| #if defined(CONFIG_CMD_NAND) |
| #define CONFIG_SYS_FLASH_BASE NAND_BASE |
| #elif defined(CONFIG_CMD_ONENAND) |
| #define CONFIG_SYS_FLASH_BASE ONENAND_MAP |
| #endif |
| |
| /* Monitor at start of flash */ |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE |
| |
| #define CONFIG_ENV_IS_IN_NAND 1 |
| #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ |
| #define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */ |
| #define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */ |
| |
| #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ |
| #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET |
| #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET |
| |
| |
| /* SMSC922x Ethernet */ |
| #if defined(CONFIG_CMD_NET) |
| #define CONFIG_SMC911X |
| #define CONFIG_SMC911X_32_BIT |
| #define CONFIG_SMC911X_BASE 0x08000000 |
| #endif /* (CONFIG_CMD_NET) */ |
| |
| /* Defines for SPL */ |
| |
| #define CONFIG_SPL_OMAP3_ID_NAND |
| |
| /* NAND: SPL falcon mode configs */ |
| #ifdef CONFIG_SPL_OS_BOOT |
| #define CONFIG_CMD_SPL_NAND_OFS 0x240000 |
| #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000 |
| #define CONFIG_CMD_SPL_WRITE_SIZE 0x2000 |
| #endif |
| |
| #endif /* __CONFIG_H */ |