| /* |
| * Cache-handling routined for MIPS CPUs |
| * |
| * Copyright (c) 2003 Wolfgang Denk <wd@denx.de> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <asm-offsets.h> |
| #include <config.h> |
| #include <asm/asm.h> |
| #include <asm/regdef.h> |
| #include <asm/mipsregs.h> |
| #include <asm/addrspace.h> |
| #include <asm/cacheops.h> |
| #include <asm/cm.h> |
| |
| #ifndef CONFIG_SYS_MIPS_CACHE_MODE |
| #define CONFIG_SYS_MIPS_CACHE_MODE CONF_CM_CACHABLE_NONCOHERENT |
| #endif |
| |
| #define INDEX_BASE CKSEG0 |
| |
| .macro f_fill64 dst, offset, val |
| LONG_S \val, (\offset + 0 * LONGSIZE)(\dst) |
| LONG_S \val, (\offset + 1 * LONGSIZE)(\dst) |
| LONG_S \val, (\offset + 2 * LONGSIZE)(\dst) |
| LONG_S \val, (\offset + 3 * LONGSIZE)(\dst) |
| LONG_S \val, (\offset + 4 * LONGSIZE)(\dst) |
| LONG_S \val, (\offset + 5 * LONGSIZE)(\dst) |
| LONG_S \val, (\offset + 6 * LONGSIZE)(\dst) |
| LONG_S \val, (\offset + 7 * LONGSIZE)(\dst) |
| #if LONGSIZE == 4 |
| LONG_S \val, (\offset + 8 * LONGSIZE)(\dst) |
| LONG_S \val, (\offset + 9 * LONGSIZE)(\dst) |
| LONG_S \val, (\offset + 10 * LONGSIZE)(\dst) |
| LONG_S \val, (\offset + 11 * LONGSIZE)(\dst) |
| LONG_S \val, (\offset + 12 * LONGSIZE)(\dst) |
| LONG_S \val, (\offset + 13 * LONGSIZE)(\dst) |
| LONG_S \val, (\offset + 14 * LONGSIZE)(\dst) |
| LONG_S \val, (\offset + 15 * LONGSIZE)(\dst) |
| #endif |
| .endm |
| |
| .macro cache_loop curr, end, line_sz, op |
| 10: cache \op, 0(\curr) |
| PTR_ADDU \curr, \curr, \line_sz |
| bne \curr, \end, 10b |
| .endm |
| |
| .macro l1_info sz, line_sz, off |
| .set push |
| .set noat |
| |
| mfc0 $1, CP0_CONFIG, 1 |
| |
| /* detect line size */ |
| srl \line_sz, $1, \off + MIPS_CONF1_DL_SHF - MIPS_CONF1_DA_SHF |
| andi \line_sz, \line_sz, (MIPS_CONF1_DL >> MIPS_CONF1_DL_SHF) |
| move \sz, zero |
| beqz \line_sz, 10f |
| li \sz, 2 |
| sllv \line_sz, \sz, \line_sz |
| |
| /* detect associativity */ |
| srl \sz, $1, \off + MIPS_CONF1_DA_SHF - MIPS_CONF1_DA_SHF |
| andi \sz, \sz, (MIPS_CONF1_DA >> MIPS_CONF1_DA_SHF) |
| addiu \sz, \sz, 1 |
| |
| /* sz *= line_sz */ |
| mul \sz, \sz, \line_sz |
| |
| /* detect log32(sets) */ |
| srl $1, $1, \off + MIPS_CONF1_DS_SHF - MIPS_CONF1_DA_SHF |
| andi $1, $1, (MIPS_CONF1_DS >> MIPS_CONF1_DS_SHF) |
| addiu $1, $1, 1 |
| andi $1, $1, 0x7 |
| |
| /* sz <<= log32(sets) */ |
| sllv \sz, \sz, $1 |
| |
| /* sz *= 32 */ |
| li $1, 32 |
| mul \sz, \sz, $1 |
| 10: |
| .set pop |
| .endm |
| /* |
| * mips_cache_reset - low level initialisation of the primary caches |
| * |
| * This routine initialises the primary caches to ensure that they have good |
| * parity. It must be called by the ROM before any cached locations are used |
| * to prevent the possibility of data with bad parity being written to memory. |
| * |
| * To initialise the instruction cache it is essential that a source of data |
| * with good parity is available. This routine will initialise an area of |
| * memory starting at location zero to be used as a source of parity. |
| * |
| * Note that this function does not follow the standard calling convention & |
| * may clobber typically callee-saved registers. |
| * |
| * RETURNS: N/A |
| * |
| */ |
| #define R_RETURN s0 |
| #define R_IC_SIZE s1 |
| #define R_IC_LINE s2 |
| #define R_DC_SIZE s3 |
| #define R_DC_LINE s4 |
| #define R_L2_SIZE s5 |
| #define R_L2_LINE s6 |
| #define R_L2_BYPASSED s7 |
| #define R_L2_L2C t8 |
| LEAF(mips_cache_reset) |
| move R_RETURN, ra |
| |
| #ifdef CONFIG_MIPS_L2_CACHE |
| /* |
| * For there to be an L2 present, Config2 must be present. If it isn't |
| * then we proceed knowing there's no L2 cache. |
| */ |
| move R_L2_SIZE, zero |
| move R_L2_LINE, zero |
| move R_L2_BYPASSED, zero |
| move R_L2_L2C, zero |
| mfc0 t0, CP0_CONFIG, 1 |
| bgez t0, l2_probe_done |
| |
| /* |
| * From MIPSr6 onwards the L2 cache configuration might not be reported |
| * by Config2. The Config5.L2C bit indicates whether this is the case, |
| * and if it is then we need knowledge of where else to look. For cores |
| * from Imagination Technologies this is a CM GCR. |
| */ |
| # if __mips_isa_rev >= 6 |
| /* Check that Config5 exists */ |
| mfc0 t0, CP0_CONFIG, 2 |
| bgez t0, l2_probe_cop0 |
| mfc0 t0, CP0_CONFIG, 3 |
| bgez t0, l2_probe_cop0 |
| mfc0 t0, CP0_CONFIG, 4 |
| bgez t0, l2_probe_cop0 |
| |
| /* Check Config5.L2C is set */ |
| mfc0 t0, CP0_CONFIG, 5 |
| and R_L2_L2C, t0, MIPS_CONF5_L2C |
| beqz R_L2_L2C, l2_probe_cop0 |
| |
| /* Config5.L2C is set */ |
| # ifdef CONFIG_MIPS_CM |
| /* The CM will provide L2 configuration */ |
| PTR_LI t0, CKSEG1ADDR(CONFIG_MIPS_CM_BASE) |
| lw t1, GCR_L2_CONFIG(t0) |
| bgez t1, l2_probe_done |
| |
| ext R_L2_LINE, t1, \ |
| GCR_L2_CONFIG_LINESZ_SHIFT, GCR_L2_CONFIG_LINESZ_BITS |
| beqz R_L2_LINE, l2_probe_done |
| li t2, 2 |
| sllv R_L2_LINE, t2, R_L2_LINE |
| |
| ext t2, t1, GCR_L2_CONFIG_ASSOC_SHIFT, GCR_L2_CONFIG_ASSOC_BITS |
| addiu t2, t2, 1 |
| mul R_L2_SIZE, R_L2_LINE, t2 |
| |
| ext t2, t1, GCR_L2_CONFIG_SETSZ_SHIFT, GCR_L2_CONFIG_SETSZ_BITS |
| sllv R_L2_SIZE, R_L2_SIZE, t2 |
| li t2, 64 |
| mul R_L2_SIZE, R_L2_SIZE, t2 |
| |
| /* Bypass the L2 cache so that we can init the L1s early */ |
| or t1, t1, GCR_L2_CONFIG_BYPASS |
| sw t1, GCR_L2_CONFIG(t0) |
| sync |
| li R_L2_BYPASSED, 1 |
| |
| /* Zero the L2 tag registers */ |
| sw zero, GCR_L2_TAG_ADDR(t0) |
| sw zero, GCR_L2_TAG_ADDR_UPPER(t0) |
| sw zero, GCR_L2_TAG_STATE(t0) |
| sw zero, GCR_L2_TAG_STATE_UPPER(t0) |
| sw zero, GCR_L2_DATA(t0) |
| sw zero, GCR_L2_DATA_UPPER(t0) |
| sync |
| # else |
| /* We don't know how to retrieve L2 configuration on this system */ |
| # endif |
| b l2_probe_done |
| # endif |
| |
| /* |
| * For pre-r6 systems, or r6 systems with Config5.L2C==0, probe the L2 |
| * cache configuration from the cop0 Config2 register. |
| */ |
| l2_probe_cop0: |
| mfc0 t0, CP0_CONFIG, 2 |
| |
| srl R_L2_LINE, t0, MIPS_CONF2_SL_SHF |
| andi R_L2_LINE, R_L2_LINE, MIPS_CONF2_SL >> MIPS_CONF2_SL_SHF |
| beqz R_L2_LINE, l2_probe_done |
| li t1, 2 |
| sllv R_L2_LINE, t1, R_L2_LINE |
| |
| srl t1, t0, MIPS_CONF2_SA_SHF |
| andi t1, t1, MIPS_CONF2_SA >> MIPS_CONF2_SA_SHF |
| addiu t1, t1, 1 |
| mul R_L2_SIZE, R_L2_LINE, t1 |
| |
| srl t1, t0, MIPS_CONF2_SS_SHF |
| andi t1, t1, MIPS_CONF2_SS >> MIPS_CONF2_SS_SHF |
| sllv R_L2_SIZE, R_L2_SIZE, t1 |
| li t1, 64 |
| mul R_L2_SIZE, R_L2_SIZE, t1 |
| |
| /* Attempt to bypass the L2 so that we can init the L1s early */ |
| or t0, t0, MIPS_CONF2_L2B |
| mtc0 t0, CP0_CONFIG, 2 |
| ehb |
| mfc0 t0, CP0_CONFIG, 2 |
| and R_L2_BYPASSED, t0, MIPS_CONF2_L2B |
| |
| /* Zero the L2 tag registers */ |
| mtc0 zero, CP0_TAGLO, 4 |
| ehb |
| l2_probe_done: |
| #endif |
| |
| #ifndef CONFIG_SYS_CACHE_SIZE_AUTO |
| li R_IC_SIZE, CONFIG_SYS_ICACHE_SIZE |
| li R_IC_LINE, CONFIG_SYS_ICACHE_LINE_SIZE |
| #else |
| l1_info R_IC_SIZE, R_IC_LINE, MIPS_CONF1_IA_SHF |
| #endif |
| |
| #ifndef CONFIG_SYS_CACHE_SIZE_AUTO |
| li R_DC_SIZE, CONFIG_SYS_DCACHE_SIZE |
| li R_DC_LINE, CONFIG_SYS_DCACHE_LINE_SIZE |
| #else |
| l1_info R_DC_SIZE, R_DC_LINE, MIPS_CONF1_DA_SHF |
| #endif |
| |
| #ifdef CONFIG_SYS_MIPS_CACHE_INIT_RAM_LOAD |
| |
| /* Determine the largest L1 cache size */ |
| #ifndef CONFIG_SYS_CACHE_SIZE_AUTO |
| #if CONFIG_SYS_ICACHE_SIZE > CONFIG_SYS_DCACHE_SIZE |
| li v0, CONFIG_SYS_ICACHE_SIZE |
| #else |
| li v0, CONFIG_SYS_DCACHE_SIZE |
| #endif |
| #else |
| move v0, R_IC_SIZE |
| sltu t1, R_IC_SIZE, R_DC_SIZE |
| movn v0, R_DC_SIZE, t1 |
| #endif |
| /* |
| * Now clear that much memory starting from zero. |
| */ |
| PTR_LI a0, CKSEG1 |
| PTR_ADDU a1, a0, v0 |
| 2: PTR_ADDIU a0, 64 |
| f_fill64 a0, -64, zero |
| bne a0, a1, 2b |
| |
| #endif /* CONFIG_SYS_MIPS_CACHE_INIT_RAM_LOAD */ |
| |
| #ifdef CONFIG_MIPS_L2_CACHE |
| /* |
| * If the L2 is bypassed, init the L1 first so that we can execute the |
| * rest of the cache initialisation using the L1 instruction cache. |
| */ |
| bnez R_L2_BYPASSED, l1_init |
| |
| l2_init: |
| PTR_LI t0, INDEX_BASE |
| PTR_ADDU t1, t0, R_L2_SIZE |
| 1: cache INDEX_STORE_TAG_SD, 0(t0) |
| PTR_ADDU t0, t0, R_L2_LINE |
| bne t0, t1, 1b |
| |
| /* |
| * If the L2 was bypassed then we already initialised the L1s before |
| * the L2, so we are now done. |
| */ |
| bnez R_L2_BYPASSED, l2_unbypass |
| #endif |
| |
| /* |
| * The TagLo registers used depend upon the CPU implementation, but the |
| * architecture requires that it is safe for software to write to both |
| * TagLo selects 0 & 2 covering supported cases. |
| */ |
| l1_init: |
| mtc0 zero, CP0_TAGLO |
| mtc0 zero, CP0_TAGLO, 2 |
| |
| /* |
| * The caches are probably in an indeterminate state, so we force good |
| * parity into them by doing an invalidate for each line. If |
| * CONFIG_SYS_MIPS_CACHE_INIT_RAM_LOAD is set then we'll proceed to |
| * perform a load/fill & a further invalidate for each line, assuming |
| * that the bottom of RAM (having just been cleared) will generate good |
| * parity for the cache. |
| */ |
| |
| /* |
| * Initialize the I-cache first, |
| */ |
| blez R_IC_SIZE, 1f |
| PTR_LI t0, INDEX_BASE |
| PTR_ADDU t1, t0, R_IC_SIZE |
| /* clear tag to invalidate */ |
| cache_loop t0, t1, R_IC_LINE, INDEX_STORE_TAG_I |
| #ifdef CONFIG_SYS_MIPS_CACHE_INIT_RAM_LOAD |
| /* fill once, so data field parity is correct */ |
| PTR_LI t0, INDEX_BASE |
| cache_loop t0, t1, R_IC_LINE, FILL |
| /* invalidate again - prudent but not strictly neccessary */ |
| PTR_LI t0, INDEX_BASE |
| cache_loop t0, t1, R_IC_LINE, INDEX_STORE_TAG_I |
| #endif |
| |
| /* Enable use of the I-cache by setting Config.K0 */ |
| sync |
| mfc0 t0, CP0_CONFIG |
| li t1, CONFIG_SYS_MIPS_CACHE_MODE |
| #if __mips_isa_rev >= 2 |
| ins t0, t1, 0, 3 |
| #else |
| ori t0, t0, CONF_CM_CMASK |
| xori t0, t0, CONF_CM_CMASK |
| or t0, t0, t1 |
| #endif |
| mtc0 t0, CP0_CONFIG |
| |
| /* |
| * then initialize D-cache. |
| */ |
| 1: blez R_DC_SIZE, 3f |
| PTR_LI t0, INDEX_BASE |
| PTR_ADDU t1, t0, R_DC_SIZE |
| /* clear all tags */ |
| cache_loop t0, t1, R_DC_LINE, INDEX_STORE_TAG_D |
| #ifdef CONFIG_SYS_MIPS_CACHE_INIT_RAM_LOAD |
| /* load from each line (in cached space) */ |
| PTR_LI t0, INDEX_BASE |
| 2: LONG_L zero, 0(t0) |
| PTR_ADDU t0, R_DC_LINE |
| bne t0, t1, 2b |
| /* clear all tags */ |
| PTR_LI t0, INDEX_BASE |
| cache_loop t0, t1, R_DC_LINE, INDEX_STORE_TAG_D |
| #endif |
| 3: |
| |
| #ifdef CONFIG_MIPS_L2_CACHE |
| /* If the L2 isn't bypassed then we're done */ |
| beqz R_L2_BYPASSED, return |
| |
| /* The L2 is bypassed - go initialise it */ |
| b l2_init |
| |
| l2_unbypass: |
| # if __mips_isa_rev >= 6 |
| beqz R_L2_L2C, 1f |
| |
| li t0, CKSEG1ADDR(CONFIG_MIPS_CM_BASE) |
| lw t1, GCR_L2_CONFIG(t0) |
| xor t1, t1, GCR_L2_CONFIG_BYPASS |
| sw t1, GCR_L2_CONFIG(t0) |
| sync |
| ehb |
| b 2f |
| # endif |
| 1: mfc0 t0, CP0_CONFIG, 2 |
| xor t0, t0, MIPS_CONF2_L2B |
| mtc0 t0, CP0_CONFIG, 2 |
| ehb |
| |
| 2: |
| # ifdef CONFIG_MIPS_CM |
| /* Config3 must exist for a CM to be present */ |
| mfc0 t0, CP0_CONFIG, 1 |
| bgez t0, 2f |
| mfc0 t0, CP0_CONFIG, 2 |
| bgez t0, 2f |
| |
| /* Check Config3.CMGCR to determine CM presence */ |
| mfc0 t0, CP0_CONFIG, 3 |
| and t0, t0, MIPS_CONF3_CMGCR |
| beqz t0, 2f |
| |
| /* Change Config.K0 to a coherent CCA */ |
| mfc0 t0, CP0_CONFIG |
| li t1, CONF_CM_CACHABLE_COW |
| #if __mips_isa_rev >= 2 |
| ins t0, t1, 0, 3 |
| #else |
| ori t0, t0, CONF_CM_CMASK |
| xori t0, t0, CONF_CM_CMASK |
| or t0, t0, t1 |
| #endif |
| mtc0 t0, CP0_CONFIG |
| |
| /* |
| * Join the coherent domain such that the caches of this core are kept |
| * coherent with those of other cores. |
| */ |
| PTR_LI t0, CKSEG1ADDR(CONFIG_MIPS_CM_BASE) |
| lw t1, GCR_REV(t0) |
| li t2, GCR_REV_CM3 |
| li t3, GCR_Cx_COHERENCE_EN |
| bge t1, t2, 1f |
| li t3, GCR_Cx_COHERENCE_DOM_EN |
| 1: sw t3, GCR_Cx_COHERENCE(t0) |
| ehb |
| 2: |
| # endif |
| #endif |
| |
| return: |
| jr ra |
| END(mips_cache_reset) |
| |
| /* |
| * dcache_status - get cache status |
| * |
| * RETURNS: 0 - cache disabled; 1 - cache enabled |
| * |
| */ |
| LEAF(dcache_status) |
| mfc0 t0, CP0_CONFIG |
| li t1, CONF_CM_UNCACHED |
| andi t0, t0, CONF_CM_CMASK |
| move v0, zero |
| beq t0, t1, 2f |
| li v0, 1 |
| 2: jr ra |
| END(dcache_status) |
| |
| /* |
| * dcache_disable - disable cache |
| * |
| * RETURNS: N/A |
| * |
| */ |
| LEAF(dcache_disable) |
| mfc0 t0, CP0_CONFIG |
| li t1, -8 |
| and t0, t0, t1 |
| ori t0, t0, CONF_CM_UNCACHED |
| mtc0 t0, CP0_CONFIG |
| jr ra |
| END(dcache_disable) |
| |
| /* |
| * dcache_enable - enable cache |
| * |
| * RETURNS: N/A |
| * |
| */ |
| LEAF(dcache_enable) |
| mfc0 t0, CP0_CONFIG |
| ori t0, CONF_CM_CMASK |
| xori t0, CONF_CM_CMASK |
| ori t0, CONFIG_SYS_MIPS_CACHE_MODE |
| mtc0 t0, CP0_CONFIG |
| jr ra |
| END(dcache_enable) |