blob: 2ed49ca8e62d1908fa7157435f6377fa6814b01c [file] [log] [blame]
Overview
=========
The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC.
The P3060 Processor combines six e500mc Power Architecture processor
cores(1.2GHz) with high-performance datapath acceleration
architecture(DPAA), CoreNet fabric infrastructure, as well as network
and peripheral bus interfaces required for networking, telecom/datacom,
wireless infrastructure, and military/aerospace applications.
P3060QDS Board Specifications:
==============================
Memory subsystem:
* 2G Bytes UDIMM DDR3(64bit bus) with ECC on
* 128M Bytes NOR flash single-chip memory
* 16M Bytes SPI flash
* 8K Bytes AT24C64 I2C EEPROM for RCW
Ethernet(Default SERDES 0x19):
* FM1-dTSEC1: connected to RGMII PHY1 (Vitesse VSC8641 on board,Bottom of dual RJ45)
* FM1-dTSEC2: connected to RGMII PHY2 (Vitesse VSC8641 on board,Top of dual RJ45)
* FM1-dTSEC3: connected to SGMII PHY (Vitesse VSC8234 port1 in slot1)
* FM1-dTSEC4: connected to SGMII PHY (Vitesse VSC8234 port3 in slot1)
* FM2-dTSEC1: connected to SGMII PHY (Vitesse VSC8234 port0 in slot2)
* FM2-dTSEC2: connected to SGMII PHY (Vitesse VSC8234 port2 in slot2)
* FM2-dTSEC3: connected to SGMII PHY (Vitesse VSC8234 port0 in slot1)
* FM2-dTSEC4: connected to SGMII PHY (Vitesse VSC8234 port2 in slot1)
PCIe:
* PCIe1: Lanes A, B, C and D of Bank1 are connected to one x4 PCIe SLOT4
* PCIe2: Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT3
RapidIO:
* sRIO1: Lanes E, F, G and H of Bank1 are connected to sRIO1 (SLOT3)
* sRIO2: Lanes A, B, C and D of Bank1 are connected to sRIO2 (SLOT4)
USB:
* USB1: connected via an external ULPI PHY SMC3315 to a TYPE-A interface
* USB2: connected via an external ULPI PHY SMC3315 to a TYPE-AB interface
I2C:
* I2C1_CH0: EEPROM AT24C64(0x50) RCW, AT24C02(0x51) DDR SPD,
AT24C02(0x53) DDR SPD, AT24C02(0x57) SystemID, RTC DS3232(0x68)
* I2C1_CH1: 1588 RiserCard(0x55), HSLB Testport, TempMon
ADT7461(0x4C), SerDesMux DS64MB201(0x51/59/5C/5D)
* I2C1_CH2: VDD/GVDD/GIDD ZL6100 (0x21/0x22/0x23/0x24/0x40)
* I2C1_CH3: OCM CFG AT24C02(0x55), OCM IPL AT24C64(0x56)
* I2C1_CH4: PCIe SLOT1
* I2C1_CH5: PCIe SLOT2
* I2C1_CH6: PCIe SLOT3
* I2C1_CH7: PCIe SLOT4
* I2C2: NULL
* I2C3: NULL
UART:
* Supports two UARTs up to 115200 bps for console
Boot from NOR flash
===================
1. Build image
export ARCH=powerpc
export CROSS_COMPILE=/your_path/gcc-4.5.xx-eglibc-2.11.xx/powerpc-linux-gnu/bin/powerpc-linux-gnu-
make P3060QDS_config
make
2. Program image
=> tftp 1000000 u-boot.bin
=> protect off all
=> erase eff80000 efffffff
=> cp.b 1000000 eff80000 80000
3. Program RCW
=> tftp 1000000 rcw.bin
=> protect off all
=> erase e8000000 e801ffff
=> cp.b 1000000 e8000000 50
4. Program FMAN Firmware ucode
=> tftp 1000000 ucode.bin
=> protect off all
=> erase ef000000 ef0fffff
=> cp.b 1000000 ef000000 2000
5. Change DIP-switch
RCW Location: SW1[1-5] = 01101 (eLBC 16bit NOR flash)
Note: 1 stands for 'on', 0 stands for 'off'
Using the Device Tree Source File
=================================
To create the DTB (Device Tree Binary) image file, use a command
similar to this:
dtc -O dtb -b 0 -p 1024 p3060qds.dts > p3060qds.dtb
Or use the following command:
{linux-2.6}/make p3060qds.dtb ARCH=powerpc
then the dtb file will be generated under the following directory:
{linux-2.6}/arch/powerpc/boot/p3060qds.dtb
Booting Linux
=============
Place a linux uImage in the TFTP disk area.
tftp 1000000 uImage
tftp 2000000 rootfs.ext2.gz.uboot
tftp 3000000 p3060rdb.dtb
bootm 1000000 2000000 3000000