blob: e1f12089c33e1139ee957f338d811ab38a0bc2db [file] [log] [blame]
/*
* Copyright 2008-2012 Freescale Semiconductor, Inc.
* Kumar Gala <kumar.gala@freescale.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <asm-offsets.h>
#include <config.h>
#include <mpc85xx.h>
#include <ppc_asm.tmpl>
#include <ppc_defs.h>
#include <asm/cache.h>
#include <asm/mmu.h>
/* To boot secondary cpus, we need a place for them to start up.
* Normally, they start at 0xfffffffc, but that's usually the
* firmware, and we don't want to have to run the firmware again.
* Instead, the primary cpu will set the BPTR to point here to
* this page. We then set up the core, and head to
* start_secondary. Note that this means that the code below
* must never exceed 1023 instructions (the branch at the end
* would then be the 1024th).
*/
.globl __secondary_start_page
.align 12
__secondary_start_page:
/* First do some preliminary setup */
lis r3, HID0_EMCP@h /* enable machine check */
#ifndef CONFIG_E500MC
ori r3,r3,HID0_TBEN@l /* enable Timebase */
#endif
#ifdef CONFIG_PHYS_64BIT
ori r3,r3,HID0_ENMAS7@l /* enable MAS7 updates */
#endif
mtspr SPRN_HID0,r3
#ifndef CONFIG_E500MC
li r3,(HID1_ASTME|HID1_ABE)@l /* Addr streaming & broadcast */
mfspr r0,PVR
andi. r0,r0,0xff
cmpwi r0,0x50@l /* if we are rev 5.0 or greater set MBDD */
blt 1f
/* Set MBDD bit also */
ori r3, r3, HID1_MBDD@l
1:
mtspr SPRN_HID1,r3
#endif
#ifdef CONFIG_SYS_FSL_ERRATUM_CPU_A003999
mfspr r3,SPRN_HDBCR1
oris r3,r3,0x0100
mtspr SPRN_HDBCR1,r3
#endif
#ifdef CONFIG_SYS_FSL_ERRATUM_A004510
mfspr r3,SPRN_SVR
rlwinm r3,r3,0,0xff
li r4,CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
cmpw r3,r4
beq 1f
#ifdef CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2
li r4,CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2
cmpw r3,r4
beq 1f
#endif
/* Not a supported revision affected by erratum */
b 2f
1: /* Erratum says set bits 55:60 to 001001 */
msync
isync
mfspr r3,SPRN_HDBCR0
li r4,0x48
rlwimi r3,r4,0,0x1f8
mtspr SPRN_HDBCR0,r3
isync
2:
#endif
/* Enable branch prediction */
lis r3,BUCSR_ENABLE@h
ori r3,r3,BUCSR_ENABLE@l
mtspr SPRN_BUCSR,r3
/* Ensure TB is 0 */
li r3,0
mttbl r3
mttbu r3
/* Enable/invalidate the I-Cache */
lis r2,(L1CSR1_ICFI|L1CSR1_ICLFR)@h
ori r2,r2,(L1CSR1_ICFI|L1CSR1_ICLFR)@l
mtspr SPRN_L1CSR1,r2
1:
mfspr r3,SPRN_L1CSR1
and. r1,r3,r2
bne 1b
lis r3,(L1CSR1_CPE|L1CSR1_ICE)@h
ori r3,r3,(L1CSR1_CPE|L1CSR1_ICE)@l
mtspr SPRN_L1CSR1,r3
isync
2:
mfspr r3,SPRN_L1CSR1
andi. r1,r3,L1CSR1_ICE@l
beq 2b
/* Enable/invalidate the D-Cache */
lis r2,(L1CSR0_DCFI|L1CSR0_DCLFR)@h
ori r2,r2,(L1CSR0_DCFI|L1CSR0_DCLFR)@l
mtspr SPRN_L1CSR0,r2
1:
mfspr r3,SPRN_L1CSR0
and. r1,r3,r2
bne 1b
lis r3,(L1CSR0_CPE|L1CSR0_DCE)@h
ori r3,r3,(L1CSR0_CPE|L1CSR0_DCE)@l
mtspr SPRN_L1CSR0,r3
isync
2:
mfspr r3,SPRN_L1CSR0
andi. r1,r3,L1CSR0_DCE@l
beq 2b
#define toreset(x) (x - __secondary_start_page + 0xfffff000)
/* get our PIR to figure out our table entry */
lis r3,toreset(__spin_table_addr)@h
ori r3,r3,toreset(__spin_table_addr)@l
lwz r3,0(r3)
mfspr r0,SPRN_PIR
#ifdef CONFIG_SYS_FSL_QORIQ_CHASSIS2
/*
* PIR definition for Chassis 2
* 0-17 Reserved (logic 0s)
* 18-19 CHIP_ID, 2'b00 - SoC 1
* all others - reserved
* 20-24 CLUSTER_ID 5'b00000 - CCM 1
* all others - reserved
* 25-26 CORE_CLUSTER_ID 2'b00 - cluster 1
* 2'b01 - cluster 2
* 2'b10 - cluster 3
* 2'b11 - cluster 4
* 27-28 CORE_ID 2'b00 - core 0
* 2'b01 - core 1
* 2'b10 - core 2
* 2'b11 - core 3
* 29-31 THREAD_ID 3'b000 - thread 0
* 3'b001 - thread 1
*
* Power-on PIR increments threads by 0x01, cores within a cluster by 0x08
* and clusters by 0x20.
*
* We renumber PIR so that all threads in the system are consecutive.
*/
rlwinm r8,r0,29,0x03 /* r8 = core within cluster */
srwi r10,r0,5 /* r10 = cluster */
mulli r5,r10,CONFIG_SYS_FSL_CORES_PER_CLUSTER
add r5,r5,r8 /* for spin table index */
mulli r4,r5,CONFIG_SYS_FSL_THREADS_PER_CORE /* for PIR */
#elif defined(CONFIG_E500MC)
rlwinm r4,r0,27,27,31
mr r5,r4
#else
mr r4,r0
mr r5,r4
#endif
/*
* r10 has the base address for the entry.
* we cannot access it yet before setting up a new TLB
*/
slwi r8,r5,6 /* spin table is padded to 64 byte */
add r10,r3,r8
mtspr SPRN_PIR,r4 /* write to PIR register */
#ifdef CONFIG_SYS_FSL_ERRATUM_A007907
mfspr r8, L1CSR2
clrrwi r8, r8, 10 /* clear bit [54-63] DCSTASHID */
mtspr L1CSR2, r8
#else
#ifdef CONFIG_SYS_CACHE_STASHING
/* set stash id to (coreID) * 2 + 32 + L1 CT (0) */
slwi r8,r4,1
addi r8,r8,32
mtspr L1CSR2,r8
#endif
#endif /* CONFIG_SYS_FSL_ERRATUM_A007907 */
#if defined(CONFIG_SYS_P4080_ERRATUM_CPU22) || \
defined(CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011)
/*
* CPU22 applies to P4080 rev 1.0, 2.0, fixed in 3.0
* NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in 3.0
* also appleis to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1
*/
mfspr r3,SPRN_SVR
rlwinm r6,r3,24,~0x800 /* clear E bit */
lis r5,SVR_P4080@h
ori r5,r5,SVR_P4080@l
cmpw r6,r5
bne 1f
rlwinm r3,r3,0,0xf0
li r5,0x30
cmpw r3,r5
bge 2f
1:
#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011
lis r3,toreset(enable_cpu_a011_workaround)@ha
lwz r3,toreset(enable_cpu_a011_workaround)@l(r3)
cmpwi r3,0
beq 2f
#endif
mfspr r3,L1CSR2
oris r3,r3,(L1CSR2_DCWS)@h
mtspr L1CSR2,r3
2:
#endif
#ifdef CONFIG_SYS_FSL_ERRATUM_A005812
/*
* A-005812 workaround sets bit 32 of SPR 976 for SoCs running in
* write shadow mode. This code should run after other code setting
* DCWS.
*/
mfspr r3,L1CSR2
andis. r3,r3,(L1CSR2_DCWS)@h
beq 1f
mfspr r3, SPRN_HDBCR0
oris r3, r3, 0x8000
mtspr SPRN_HDBCR0, r3
1:
#endif
#ifdef CONFIG_BACKSIDE_L2_CACHE
/* skip L2 setup on P2040/P2040E as they have no L2 */
mfspr r3,SPRN_SVR
rlwinm r6,r3,24,~0x800 /* clear E bit of SVR */
lis r3,SVR_P2040@h
ori r3,r3,SVR_P2040@l
cmpw r6,r3
beq 3f
/* Enable/invalidate the L2 cache */
msync
lis r2,(L2CSR0_L2FI|L2CSR0_L2LFC)@h
ori r2,r2,(L2CSR0_L2FI|L2CSR0_L2LFC)@l
mtspr SPRN_L2CSR0,r2
1:
mfspr r3,SPRN_L2CSR0
and. r1,r3,r2
bne 1b
#ifdef CONFIG_SYS_CACHE_STASHING
/* set stash id to (coreID) * 2 + 32 + L2 (1) */
addi r3,r8,1
mtspr SPRN_L2CSR1,r3
#endif
lis r3,CONFIG_SYS_INIT_L2CSR0@h
ori r3,r3,CONFIG_SYS_INIT_L2CSR0@l
mtspr SPRN_L2CSR0,r3
isync
2:
mfspr r3,SPRN_L2CSR0
andis. r1,r3,L2CSR0_L2E@h
beq 2b
#endif
3:
/* setup mapping for the spin table, WIMGE=0b00100 */
lis r13,toreset(__spin_table_addr)@h
ori r13,r13,toreset(__spin_table_addr)@l
lwz r13,0(r13)
/* mask by 4K */
rlwinm r13,r13,0,0,19
lis r11,(MAS0_TLBSEL(1)|MAS0_ESEL(1))@h
mtspr SPRN_MAS0,r11
lis r11,(MAS1_VALID|MAS1_IPROT)@h
ori r11,r11,(MAS1_TS|MAS1_TSIZE(BOOKE_PAGESZ_4K))@l
mtspr SPRN_MAS1,r11
oris r11,r13,(MAS2_M|MAS2_G)@h
ori r11,r13,(MAS2_M|MAS2_G)@l
mtspr SPRN_MAS2,r11
oris r11,r13,(MAS3_SX|MAS3_SW|MAS3_SR)@h
ori r11,r13,(MAS3_SX|MAS3_SW|MAS3_SR)@l
mtspr SPRN_MAS3,r11
li r11,0
mtspr SPRN_MAS7,r11
tlbwe
/*
* __bootpg_addr has the address of __second_half_boot_page
* jump there in AS=1 space with cache enabled
*/
lis r13,toreset(__bootpg_addr)@h
ori r13,r13,toreset(__bootpg_addr)@l
lwz r11,0(r13)
mtspr SPRN_SRR0,r11
mfmsr r13
ori r12,r13,MSR_IS|MSR_DS@l
mtspr SPRN_SRR1,r12
rfi
/*
* Allocate some space for the SDRAM address of the bootpg.
* This variable has to be in the boot page so that it can
* be accessed by secondary cores when they come out of reset.
*/
.align L1_CACHE_SHIFT
.globl __bootpg_addr
__bootpg_addr:
.long 0
.global __spin_table_addr
__spin_table_addr:
.long 0
/*
* This variable is set by cpu_init_r() after parsing hwconfig
* to enable workaround for erratum NMG_CPU_A011.
*/
.align L1_CACHE_SHIFT
.global enable_cpu_a011_workaround
enable_cpu_a011_workaround:
.long 1
/* Fill in the empty space. The actual reset vector is
* the last word of the page */
__secondary_start_code_end:
.space 4092 - (__secondary_start_code_end - __secondary_start_page)
__secondary_reset_vector:
b __secondary_start_page
/* this is a separated page for the spin table and cacheable boot code */
.align L1_CACHE_SHIFT
.global __second_half_boot_page
__second_half_boot_page:
#ifdef CONFIG_PPC_SPINTABLE_COMPATIBLE
lis r3,(spin_table_compat - __second_half_boot_page)@h
ori r3,r3,(spin_table_compat - __second_half_boot_page)@l
add r3,r3,r11 /* r11 has the address of __second_half_boot_page */
lwz r14,0(r3)
#endif
#define ENTRY_ADDR_UPPER 0
#define ENTRY_ADDR_LOWER 4
#define ENTRY_R3_UPPER 8
#define ENTRY_R3_LOWER 12
#define ENTRY_RESV 16
#define ENTRY_PIR 20
#define ENTRY_SIZE 64
/*
* setup the entry
* r10 has the base address of the spin table.
* spin table is defined as
* struct {
* uint64_t entry_addr;
* uint64_t r3;
* uint32_t rsvd1;
* uint32_t pir;
* };
* we pad this struct to 64 bytes so each entry is in its own cacheline
*/
li r3,0
li r8,1
mfspr r4,SPRN_PIR
stw r3,ENTRY_ADDR_UPPER(r10)
stw r3,ENTRY_R3_UPPER(r10)
stw r4,ENTRY_R3_LOWER(r10)
stw r3,ENTRY_RESV(r10)
stw r4,ENTRY_PIR(r10)
msync
stw r8,ENTRY_ADDR_LOWER(r10)
/* spin waiting for addr */
3:
/*
* To comply with ePAPR 1.1, the spin table has been moved to cache-enabled
* memory. Old OS may not work with this change. A patch is waiting to be
* accepted for Linux kernel. Other OS needs similar fix to spin table.
* For OSes with old spin table code, we can enable this temporary fix by
* setting environmental variable "spin_table_compat". For new OSes, set
* "spin_table_compat=no". After Linux is fixed, we can remove this macro
* and related code. For now, it is enabled by default.
*/
#ifdef CONFIG_PPC_SPINTABLE_COMPATIBLE
cmpwi r14,0
beq 4f
dcbf 0, r10
sync
4:
#endif
lwz r4,ENTRY_ADDR_LOWER(r10)
andi. r11,r4,1
bne 3b
isync
/* get the upper bits of the addr */
lwz r11,ENTRY_ADDR_UPPER(r10)
/* setup branch addr */
mtspr SPRN_SRR0,r4
/* mark the entry as released */
li r8,3
stw r8,ENTRY_ADDR_LOWER(r10)
/* mask by ~64M to setup our tlb we will jump to */
rlwinm r12,r4,0,0,5
/*
* setup r3, r4, r5, r6, r7, r8, r9
* r3 contains the value to put in the r3 register at secondary cpu
* entry. The high 32-bits are ignored on 32-bit chip implementations.
* 64-bit chip implementations however shall load all 64-bits
*/
#ifdef CONFIG_SYS_PPC64
ld r3,ENTRY_R3_UPPER(r10)
#else
lwz r3,ENTRY_R3_LOWER(r10)
#endif
li r4,0
li r5,0
li r6,0
lis r7,(64*1024*1024)@h
li r8,0
li r9,0
/* load up the pir */
lwz r0,ENTRY_PIR(r10)
mtspr SPRN_PIR,r0
mfspr r0,SPRN_PIR
stw r0,ENTRY_PIR(r10)
mtspr IVPR,r12
/*
* Coming here, we know the cpu has one TLB mapping in TLB1[0]
* which maps 0xfffff000-0xffffffff one-to-one. We set up a
* second mapping that maps addr 1:1 for 64M, and then we jump to
* addr
*/
lis r10,(MAS0_TLBSEL(1)|MAS0_ESEL(0))@h
mtspr SPRN_MAS0,r10
lis r10,(MAS1_VALID|MAS1_IPROT)@h
ori r10,r10,(MAS1_TSIZE(BOOKE_PAGESZ_64M))@l
mtspr SPRN_MAS1,r10
/* WIMGE = 0b00000 for now */
mtspr SPRN_MAS2,r12
ori r12,r12,(MAS3_SX|MAS3_SW|MAS3_SR)
mtspr SPRN_MAS3,r12
#ifdef CONFIG_ENABLE_36BIT_PHYS
mtspr SPRN_MAS7,r11
#endif
tlbwe
/* Now we have another mapping for this page, so we jump to that
* mapping
*/
mtspr SPRN_SRR1,r13
rfi
.align 6
.globl __spin_table
__spin_table:
.space CONFIG_MAX_CPUS*ENTRY_SIZE
#ifdef CONFIG_PPC_SPINTABLE_COMPATIBLE
.align L1_CACHE_SHIFT
.global spin_table_compat
spin_table_compat:
.long 1
#endif
__spin_table_end:
.space 4096 - (__spin_table_end - __spin_table)