blob: ed5cde3a0b7f10cbc86a46e50987e127037255c7 [file] [log] [blame]
/*
* Board functions for TI AM335X based rut board
* (C) Copyright 2013 Siemens Schweiz AG
* (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* Based on:
* u-boot:/board/ti/am335x/board.c
*
* Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <errno.h>
#include <spi.h>
#include <spl.h>
#include <asm/arch/cpu.h>
#include <asm/arch/hardware.h>
#include <asm/arch/omap.h>
#include <asm/arch/ddr_defs.h>
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/sys_proto.h>
#include <asm/io.h>
#include <asm/emif.h>
#include <asm/gpio.h>
#include <i2c.h>
#include <miiphy.h>
#include <cpsw.h>
#include <video.h>
#include <watchdog.h>
#include "board.h"
#include "../common/factoryset.h"
#include "../../../drivers/video/da8xx-fb.h"
/*
* Read header information from EEPROM into global structure.
*/
static int read_eeprom(void)
{
return 0;
}
#ifdef CONFIG_SPL_BUILD
static void board_init_ddr(void)
{
struct emif_regs rut_ddr3_emif_reg_data = {
.sdram_config = 0x61C04AB2,
.sdram_tim1 = 0x0888A39B,
.sdram_tim2 = 0x26337FDA,
.sdram_tim3 = 0x501F830F,
.emif_ddr_phy_ctlr_1 = 0x6,
.zq_config = 0x50074BE4,
.ref_ctrl = 0x93B,
};
struct ddr_data rut_ddr3_data = {
.datardsratio0 = 0x3b,
.datawdsratio0 = 0x85,
.datafwsratio0 = 0x100,
.datawrsratio0 = 0xc1,
};
struct cmd_control rut_ddr3_cmd_ctrl_data = {
.cmd0csratio = 0x40,
.cmd0iclkout = 1,
.cmd1csratio = 0x40,
.cmd1iclkout = 1,
.cmd2csratio = 0x40,
.cmd2iclkout = 1,
};
const struct ctrl_ioregs ioregs = {
.cm0ioctl = RUT_IOCTRL_VAL,
.cm1ioctl = RUT_IOCTRL_VAL,
.cm2ioctl = RUT_IOCTRL_VAL,
.dt0ioctl = RUT_IOCTRL_VAL,
.dt1ioctl = RUT_IOCTRL_VAL,
};
config_ddr(DDR_PLL_FREQ, &ioregs, &rut_ddr3_data,
&rut_ddr3_cmd_ctrl_data, &rut_ddr3_emif_reg_data, 0);
}
static int request_and_pulse_reset(int gpio, const char *name)
{
int ret;
const int delay_us = 2000; /* 2ms */
ret = gpio_request(gpio, name);
if (ret < 0) {
printf("%s: Unable to request %s\n", __func__, name);
goto err;
}
ret = gpio_direction_output(gpio, 0);
if (ret < 0) {
printf("%s: Unable to set %s as output\n", __func__, name);
goto err_free_gpio;
}
udelay(delay_us);
gpio_set_value(gpio, 1);
return 0;
err_free_gpio:
gpio_free(gpio);
err:
return ret;
}
#define GPIO_TO_PIN(bank, gpio) (32 * (bank) + (gpio))
#define ETH_PHY_RESET_GPIO GPIO_TO_PIN(2, 18)
#define MAXTOUCH_RESET_GPIO GPIO_TO_PIN(3, 18)
#define DISPLAY_RESET_GPIO GPIO_TO_PIN(3, 19)
#define REQUEST_AND_PULSE_RESET(N) \
request_and_pulse_reset(N, #N);
static void spl_siemens_board_init(void)
{
REQUEST_AND_PULSE_RESET(ETH_PHY_RESET_GPIO);
REQUEST_AND_PULSE_RESET(MAXTOUCH_RESET_GPIO);
REQUEST_AND_PULSE_RESET(DISPLAY_RESET_GPIO);
}
#endif /* if def CONFIG_SPL_BUILD */
#if defined(CONFIG_DRIVER_TI_CPSW)
static void cpsw_control(int enabled)
{
/* VTP can be added here */
return;
}
static struct cpsw_slave_data cpsw_slaves[] = {
{
.slave_reg_ofs = 0x208,
.sliver_reg_ofs = 0xd80,
.phy_addr = 1,
.phy_if = PHY_INTERFACE_MODE_RMII,
},
{
.slave_reg_ofs = 0x308,
.sliver_reg_ofs = 0xdc0,
.phy_addr = 0,
.phy_if = PHY_INTERFACE_MODE_RMII,
},
};
static struct cpsw_platform_data cpsw_data = {
.mdio_base = CPSW_MDIO_BASE,
.cpsw_base = CPSW_BASE,
.mdio_div = 0xff,
.channels = 8,
.cpdma_reg_ofs = 0x800,
.slaves = 1,
.slave_data = cpsw_slaves,
.ale_reg_ofs = 0xd00,
.ale_entries = 1024,
.host_port_reg_ofs = 0x108,
.hw_stats_reg_ofs = 0x900,
.bd_ram_ofs = 0x2000,
.mac_control = (1 << 5),
.control = cpsw_control,
.host_port_num = 0,
.version = CPSW_CTRL_VERSION_2,
};
#if defined(CONFIG_DRIVER_TI_CPSW) || \
(defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET))
int board_eth_init(bd_t *bis)
{
struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
int n = 0;
int rv;
#ifndef CONFIG_SPL_BUILD
factoryset_env_set();
#endif
/* Set rgmii mode and enable rmii clock to be sourced from chip */
writel((RMII_MODE_ENABLE | RMII_CHIPCKL_ENABLE), &cdev->miisel);
rv = cpsw_register(&cpsw_data);
if (rv < 0)
printf("Error %d registering CPSW switch\n", rv);
else
n += rv;
return n;
}
#endif /* #if defined(CONFIG_DRIVER_TI_CPSW) */
#endif /* #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) */
#if defined(CONFIG_HW_WATCHDOG)
static bool hw_watchdog_init_done;
static int hw_watchdog_trigger_level;
void hw_watchdog_reset(void)
{
if (!hw_watchdog_init_done)
return;
hw_watchdog_trigger_level = hw_watchdog_trigger_level ? 0 : 1;
gpio_set_value(WATCHDOG_TRIGGER_GPIO, hw_watchdog_trigger_level);
}
void hw_watchdog_init(void)
{
gpio_request(WATCHDOG_TRIGGER_GPIO, "watchdog_trigger");
gpio_direction_output(WATCHDOG_TRIGGER_GPIO, hw_watchdog_trigger_level);
hw_watchdog_reset();
hw_watchdog_init_done = 1;
}
#endif /* defined(CONFIG_HW_WATCHDOG) */
#if defined(CONFIG_VIDEO) && !defined(CONFIG_SPL_BUILD)
static struct da8xx_panel lcd_panels[] = {
/* FORMIKE, 4.3", 480x800, KWH043MC17-F01 */
[0] = {
.name = "KWH043MC17-F01",
.width = 480,
.height = 800,
.hfp = 50, /* no spec, "don't care" values */
.hbp = 50,
.hsw = 50,
.vfp = 50,
.vbp = 50,
.vsw = 50,
.pxl_clk = 35910000, /* tCYCD=20ns, max 50MHz, 60fps */
.invert_pxl_clk = 1,
},
/* FORMIKE, 4.3", 480x800, KWH043ST20-F01 */
[1] = {
.name = "KWH043ST20-F01",
.width = 480,
.height = 800,
.hfp = 50, /* no spec, "don't care" values */
.hbp = 50,
.hsw = 50,
.vfp = 50,
.vbp = 50,
.vsw = 50,
.pxl_clk = 35910000, /* tCYCD=20ns, max 50MHz, 60fps */
.invert_pxl_clk = 1,
},
/* Multi-Inno, 4.3", 480x800, MI0430VT-1 */
[2] = {
.name = "MI0430VT-1",
.width = 480,
.height = 800,
.hfp = 50, /* no spec, "don't care" values */
.hbp = 50,
.hsw = 50,
.vfp = 50,
.vbp = 50,
.vsw = 50,
.pxl_clk = 35910000, /* tCYCD=20ns, max 50MHz, 60fps */
.invert_pxl_clk = 1,
},
};
static const struct display_panel disp_panels[] = {
[0] = {
WVGA,
16, /* RGB 888 */
16,
COLOR_ACTIVE,
},
[1] = {
WVGA,
16, /* RGB 888 */
16,
COLOR_ACTIVE,
},
[2] = {
WVGA,
24, /* RGB 888 */
16,
COLOR_ACTIVE,
},
};
static const struct lcd_ctrl_config lcd_cfgs[] = {
[0] = {
&disp_panels[0],
.ac_bias = 255,
.ac_bias_intrpt = 0,
.dma_burst_sz = 16,
.bpp = 16,
.fdd = 0x80,
.tft_alt_mode = 0,
.stn_565_mode = 0,
.mono_8bit_mode = 0,
.invert_line_clock = 1,
.invert_frm_clock = 1,
.sync_edge = 0,
.sync_ctrl = 1,
.raster_order = 0,
},
[1] = {
&disp_panels[1],
.ac_bias = 255,
.ac_bias_intrpt = 0,
.dma_burst_sz = 16,
.bpp = 16,
.fdd = 0x80,
.tft_alt_mode = 0,
.stn_565_mode = 0,
.mono_8bit_mode = 0,
.invert_line_clock = 1,
.invert_frm_clock = 1,
.sync_edge = 0,
.sync_ctrl = 1,
.raster_order = 0,
},
[2] = {
&disp_panels[2],
.ac_bias = 255,
.ac_bias_intrpt = 0,
.dma_burst_sz = 16,
.bpp = 24,
.fdd = 0x80,
.tft_alt_mode = 0,
.stn_565_mode = 0,
.mono_8bit_mode = 0,
.invert_line_clock = 1,
.invert_frm_clock = 1,
.sync_edge = 0,
.sync_ctrl = 1,
.raster_order = 0,
},
};
/* no console on this board */
int board_cfb_skip(void)
{
return 1;
}
#define PLL_GET_M(v) ((v >> 8) & 0x7ff)
#define PLL_GET_N(v) (v & 0x7f)
static struct dpll_regs dpll_lcd_regs = {
.cm_clkmode_dpll = CM_WKUP + 0x98,
.cm_idlest_dpll = CM_WKUP + 0x48,
.cm_clksel_dpll = CM_WKUP + 0x54,
};
static int get_clk(struct dpll_regs *dpll_regs)
{
unsigned int val;
unsigned int m, n;
int f = 0;
val = readl(dpll_regs->cm_clksel_dpll);
m = PLL_GET_M(val);
n = PLL_GET_N(val);
f = (m * V_OSCK) / n;
return f;
};
int clk_get(int clk)
{
return get_clk(&dpll_lcd_regs);
};
static int conf_disp_pll(int m, int n)
{
struct cm_perpll *cmper = (struct cm_perpll *)CM_PER;
struct dpll_params dpll_lcd = {m, n, -1, -1, -1, -1, -1};
#if defined(DISPL_PLL_SPREAD_SPECTRUM)
struct cm_wkuppll *cmwkup = (struct cm_wkuppll *)CM_WKUP;
#endif
u32 *const clk_domains[] = {
&cmper->lcdclkctrl,
0
};
u32 *const clk_modules_explicit_en[] = {
&cmper->lcdclkctrl,
&cmper->lcdcclkstctrl,
&cmper->spi1clkctrl,
0
};
do_enable_clocks(clk_domains, clk_modules_explicit_en, 1);
do_setup_dpll(&dpll_lcd_regs, &dpll_lcd);
#if defined(DISPL_PLL_SPREAD_SPECTRUM)
writel(0x64, &cmwkup->resv6[3]); /* 0x50 */
writel(0x800, &cmwkup->resv6[2]); /* 0x4c */
writel(readl(&cmwkup->clkmoddplldisp) | CM_CLKMODE_DPLL_SSC_EN_MASK,
&cmwkup->clkmoddplldisp); /* 0x98 */
#endif
return 0;
}
static int set_gpio(int gpio, int state)
{
gpio_request(gpio, "temp");
gpio_direction_output(gpio, state);
gpio_set_value(gpio, state);
gpio_free(gpio);
return 0;
}
static int enable_lcd(void)
{
unsigned char buf[1];
set_gpio(BOARD_LCD_RESET, 0);
mdelay(1);
set_gpio(BOARD_LCD_RESET, 1);
mdelay(1);
/* spi lcd init */
kwh043st20_f01_spi_startup(1, 0, 5000000, SPI_MODE_0);
/* backlight on */
buf[0] = 0xf;
i2c_write(0x24, 0x7, 1, buf, 1);
buf[0] = 0x3f;
i2c_write(0x24, 0x8, 1, buf, 1);
return 0;
}
int arch_early_init_r(void)
{
enable_lcd();
return 0;
}
static int board_video_init(void)
{
int i;
int anzdisp = ARRAY_SIZE(lcd_panels);
int display = 1;
for (i = 0; i < anzdisp; i++) {
if (strncmp((const char *)factory_dat.disp_name,
lcd_panels[i].name,
strlen((const char *)factory_dat.disp_name)) == 0) {
printf("DISPLAY: %s\n", factory_dat.disp_name);
break;
}
}
if (i == anzdisp) {
i = 1;
printf("%s: %s not found, using default %s\n", __func__,
factory_dat.disp_name, lcd_panels[i].name);
}
conf_disp_pll(24, 1);
da8xx_video_init(&lcd_panels[display], &lcd_cfgs[display],
lcd_cfgs[display].bpp);
return 0;
}
#endif /* ifdef CONFIG_VIDEO */
#ifdef CONFIG_BOARD_LATE_INIT
int board_late_init(void)
{
int ret;
char tmp[2 * MAX_STRING_LENGTH + 2];
omap_nand_switch_ecc(1, 8);
if (factory_dat.asn[0] != 0)
sprintf(tmp, "%s_%s", factory_dat.asn,
factory_dat.comp_version);
else
strcpy(tmp, "QMX7.E38_4.0");
ret = env_set("boardid", tmp);
if (ret)
printf("error setting board id\n");
return 0;
}
#endif
#include "../common/board.c"