| ================================================================================ |
| Board Information |
| ================================================================================ |
| |
| Developed by HiSilicon, the board features the Hi3798C V200 with an |
| integrated quad-core 64-bit ARM Cortex A53 processor and high |
| performance Mali T720 GPU, making it capable of running any commercial |
| set-top solution based on Linux or Android. Its high performance |
| specification also supports a premium user experience with up to H.265 |
| HEVC decoding of 4K video at 60 frames per second. |
| |
| SOC Hisilicon Hi3798CV200 |
| CPU Quad-core ARM Cortex-A53 64 bit |
| DRAM DDR3/3L/4 SDRAM interface, maximum 32-bit data width 2 GB |
| USB Two USB 2.0 ports One USB 3.0 ports |
| CONSOLE USB-micro port for console support |
| ETHERNET 1 GBe Ethernet |
| PCIE One PCIe 2.0 interfaces |
| JTAG 8-Pin JTAG |
| EXPANSION INTERFACE Linaro 96Boards Low Speed Expansion slot |
| DIMENSION Standard 160×120 mm 96Boards Enterprice Edition form factor |
| WIFI 802.11AC 2*2 with Bluetooth |
| CONNECTORS One connector for Smart Card One connector for TSI |
| |
| |
| ================================================================================ |
| BUILD INSTRUCTIONS |
| ================================================================================ |
| |
| Note of warning: |
| ================ |
| |
| U-Boot has a *strong* dependency with the l-loader and the arm trusted firmware |
| repositories. |
| |
| The boot sequence is: |
| l-loader --> arm_trusted_firmware --> u-boot |
| |
| U-Boot needs to be aware of the BL31 runtime location and size to avoid writing |
| over it. Currently, BL31 is being placed below the kernel text offset (check |
| poplar.c) but this could change in the future. |
| |
| The current version of u-boot has been tested with: |
| - https://github.com/Linaro/poplar-l-loader.git |
| |
| commit f0988698dcc5c08bd0a8f50aa0457e138a5f438c |
| Author: Alex Elder <elder@linaro.org> |
| Date: Fri Jun 16 08:57:59 2017 -0500 |
| |
| l-loader: use external memory region definitions |
| |
| The ARM Trusted Firmware code now has a header file that collects |
| all the definitions for the memory regions used for its boot stages. |
| Include that file where needed, and use the definitions found therein |
| |
| Signed-off-by: Alex Elder <elder@linaro.org> |
| |
| |
| - https://github.com/Linaro/poplar-arm-trusted-firmware.git |
| |
| commit 6ac42dd3be13c99aa8ce29a15073e2f19d935f68 |
| Author: Alex Elder <elder@linaro.org> |
| Date: Fri Jun 16 09:24:50 2017 -0500 |
| |
| poplar: define memory regions in a separate file |
| |
| Separate the definitions for memory regions used for the BL stage |
| images and FIP into a new file. The "l-loader" image uses knowledge |
| of the sizes and locations of these memory regions, and it can now |
| include this (external) header to get these definitions, rather than |
| having to make coordinated changes to both code bases. |
| |
| The new file has a complete set of definitions (more than may be |
| required by one or the other user). It also includes a summary of |
| how the boot process works, and how it uses these regions. |
| |
| It should now be relatively easy to adjust the sizes and locations |
| of these memory regions, or to add to them (e.g. for TEE). |
| |
| Signed-off-by: Alex Elder <elder@linaro.org> |
| |
| |
| Compile from source: |
| ==================== |
| |
| Get all the sources |
| |
| > mkdir -p ~/poplar/src ~/poplar/bin |
| > cd ~/poplar/src |
| > git clone https://github.com/Linaro/poplar-l-loader.git l-loader |
| > git clone https://github.com/Linaro/poplar-arm-trusted-firmware.git atf |
| > git clone https://github.com/Linaro/poplar-u-boot.git u-boot |
| |
| Make sure you are using the correct branch on each one of these repositories. |
| The definition of "correct" might change over time (at this moment in time this |
| would be the "latest" branch). |
| |
| Compile U-Boot: |
| =============== |
| |
| Prerequisite: |
| # sudo apt-get install device-tree-compiler |
| |
| > cd ~/poplar/src/u-boot |
| > make CROSS_COMPILE=aarch64-linux-gnu- poplar_defconfig |
| > make CROSS_COMPILE=aarch64-linux-gnu- |
| > cp u-boot.bin ~/poplar/bin |
| |
| Compile ARM Trusted Firmware (ATF): |
| =================================== |
| |
| > cd ~/poplar/src/atf |
| > make CROSS_COMPILE=aarch64-linux-gnu- all fip \ |
| SPD=none BL33=~/poplar/bin/u-boot.bin DEBUG=1 PLAT=poplar |
| |
| Copy resulting binaries |
| > cp build/hi3798cv200/debug/bl1.bin ~/poplar/src/l-loader/atf/ |
| > cp build/hi3798cv200/debug/fip.bin ~/poplar/src/l-loader/atf/ |
| |
| Compile l-loader: |
| ================= |
| |
| > cd ~/poplar/src/l-loader |
| > make clean |
| > make CROSS_COMPILE=arm-linux-gnueabi- |
| |
| Due to BootROM requiremets, rename l-loader.bin to fastboot.bin: |
| > cp l-loader.bin ~/poplar/bin/fastboot.bin |
| |
| |
| ================================================================================ |
| FLASH INSTRUCTIONS |
| ================================================================================ |
| |
| Two methods: |
| |
| Using USB debrick support: |
| Copy fastboot.bin to a FAT partition on the USB drive and reboot the |
| poplar board while pressing S3(usb_boot). |
| |
| The system will execute the new u-boot and boot into a shell which you |
| can then use to write to eMMC. |
| |
| Using U-BOOT from shell: |
| 1) using AXIS usb ethernet dongle and tftp |
| 2) using FAT formated USB drive |
| |
| |
| 1. TFTP (USB ethernet dongle) |
| ============================= |
| |
| Plug a USB AXIS ethernet dongle on any of the USB2 ports on the Poplar board. |
| Copy fastboot.bin to your tftp server. |
| In u-boot make sure your network is properly setup. |
| |
| Then |
| |
| => tftp 0x30000000 fastboot.bin |
| starting USB... |
| USB0: USB EHCI 1.00 |
| scanning bus 0 for devices... 1 USB Device(s) found |
| USB1: USB EHCI 1.00 |
| scanning bus 1 for devices... 3 USB Device(s) found |
| scanning usb for storage devices... 0 Storage Device(s) found |
| scanning usb for ethernet devices... 1 Ethernet Device(s) found |
| Waiting for Ethernet connection... done. |
| Using asx0 device |
| TFTP from server 192.168.1.4; our IP address is 192.168.1.10 |
| Filename 'poplar/fastboot.bin'. |
| Load address: 0x30000000 |
| Loading: ################################################################# |
| ################################################################# |
| ############################################################### |
| 2 MiB/s |
| done |
| Bytes transferred = 983040 (f0000 hex) |
| |
| => mmc write 0x30000000 0 0x780 |
| |
| MMC write: dev # 0, block # 0, count 1920 ... 1920 blocks written: OK |
| => reset |
| |
| |
| 2. USING USB FAT DRIVE |
| ======================= |
| |
| Copy fastboot.bin to any partition on a FAT32 formated usb flash drive. |
| Enter the uboot prompt |
| |
| => fatls usb 0:2 |
| 983040 fastboot.bin |
| |
| 1 file(s), 0 dir(s) |
| |
| => fatload usb 0:2 0x30000000 fastboot.bin |
| reading fastboot.bin |
| 983040 bytes read in 44 ms (21.3 MiB/s) |
| |
| => mmc write 0x30000000 0 0x780 |
| |
| MMC write: dev # 0, block # 0, count 1920 ... 1920 blocks written: OK |
| |
| |
| ================================================================================ |
| BOOT TRACE |
| ================================================================================ |
| |
| Bootrom start |
| Boot Media: eMMC |
| Decrypt auxiliary code ...OK |
| |
| lsadc voltage min: 000000FE, max: 000000FF, aver: 000000FE, index: 00000000 |
| |
| Entry boot auxiliary code |
| |
| Auxiliary code - v1.00 |
| DDR code - V1.1.2 20160205 |
| Build: Mar 24 2016 - 17:09:44 |
| Reg Version: v134 |
| Reg Time: 2016/03/18 09:44:55 |
| Reg Name: hi3798cv2dmb_hi3798cv200_ddr3_2gbyte_8bitx4_4layers.reg |
| |
| Boot auxiliary code success |
| Bootrom success |
| |
| LOADER: Switched to aarch64 mode |
| LOADER: Entering ARM TRUSTED FIRMWARE |
| LOADER: CPU0 executes at 0x000ce000 |
| |
| INFO: BL1: 0xe1000 - 0xe7000 [size = 24576] |
| NOTICE: Booting Trusted Firmware |
| NOTICE: BL1: v1.3(debug):v1.3-372-g1ba9c60 |
| NOTICE: BL1: Built : 17:51:33, Apr 30 2017 |
| INFO: BL1: RAM 0xe1000 - 0xe7000 |
| INFO: BL1: Loading BL2 |
| INFO: Loading image id=1 at address 0xe9000 |
| INFO: Image id=1 loaded at address 0xe9000, size = 0x5008 |
| NOTICE: BL1: Booting BL2 |
| INFO: Entry point address = 0xe9000 |
| INFO: SPSR = 0x3c5 |
| NOTICE: BL2: v1.3(debug):v1.3-372-g1ba9c60 |
| NOTICE: BL2: Built : 17:51:33, Apr 30 2017 |
| INFO: BL2: Loading BL31 |
| INFO: Loading image id=3 at address 0x129000 |
| INFO: Image id=3 loaded at address 0x129000, size = 0x8038 |
| INFO: BL2: Loading BL33 |
| INFO: Loading image id=5 at address 0x37000000 |
| INFO: Image id=5 loaded at address 0x37000000, size = 0x58f17 |
| NOTICE: BL1: Booting BL31 |
| INFO: Entry point address = 0x129000 |
| INFO: SPSR = 0x3cd |
| INFO: Boot bl33 from 0x37000000 for 364311 Bytes |
| NOTICE: BL31: v1.3(debug):v1.3-372-g1ba9c60 |
| NOTICE: BL31: Built : 17:51:33, Apr 30 2017 |
| INFO: BL31: Initializing runtime services |
| INFO: BL31: Preparing for EL3 exit to normal world |
| INFO: Entry point address = 0x37000000 |
| INFO: SPSR = 0x3c9 |
| |
| |
| U-Boot 2017.05-rc2-00130-gd2255b0 (Apr 30 2017 - 17:51:28 +0200)poplar |
| |
| Model: HiSilicon Poplar Development Board |
| BOARD: Hisilicon HI3798cv200 Poplar |
| DRAM: 1 GiB |
| MMC: Hisilicon DWMMC: 0 |
| In: serial@f8b00000 |
| Out: serial@f8b00000 |
| Err: serial@f8b00000 |
| Net: Net Initialization Skipped |
| No ethernet found. |
| |
| Hit any key to stop autoboot: 0 |
| starting USB... |
| USB0: USB EHCI 1.00 |
| scanning bus 0 for devices... 1 USB Device(s) found |
| USB1: USB EHCI 1.00 |
| scanning bus 1 for devices... 4 USB Device(s) found |
| scanning usb for storage devices... 1 Storage Device(s) found |
| scanning usb for ethernet devices... 1 Ethernet Device(s) found |
| |
| USB device 0: |
| Device 0: Vendor: SanDisk Rev: 1.00 Prod: Cruzer Blade |
| Type: Removable Hard Disk |
| Capacity: 7632.0 MB = 7.4 GB (15630336 x 512) |
| ... is now current device |
| Scanning usb 0:1... |
| => |