| /* |
| * (C) Copyright 2001 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /* |
| * Configuration settings for the sbc8240 board. |
| */ |
| |
| /* ------------------------------------------------------------------------- */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_MPC824X 1 |
| #define CONFIG_MPC8240 1 |
| #define CONFIG_WRSBC8240 1 |
| |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_BAUDRATE 9600 |
| #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } |
| |
| #define CONFIG_PREBOOT "echo;echo Welcome to U-Boot for the sbc8240;echo;echo Type \"? or help\" to get on-line help;echo" |
| |
| #undef CONFIG_BOOTARGS |
| |
| #define CONFIG_BOOTCOMMAND "version;echo;tftpboot $loadaddr $loadfile;bootvx" /* autoboot command */ |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "bootargs=$fei(0,0)host:/T221ppc/target/config/sbc8240/vxWorks.st " \ |
| "e=192.168.193.102 h=192.168.193.99 u=target pw=hello f=0x08 " \ |
| "tn=sbc8240 o=fei \0" \ |
| "env_startaddr=FFF70000\0" \ |
| "env_endaddr=FFF7FFFF\0" \ |
| "loadfile=vxWorks.st\0" \ |
| "loadaddr=0x01000000\0" \ |
| "net_load=tftpboot $loadaddr $loadfile\0" \ |
| "uboot_startaddr=FFF00000\0" \ |
| "uboot_endaddr=FFF3FFFF\0" \ |
| "update=tftp $loadaddr /u-boot.bin;" \ |
| "protect off $uboot_startaddr $uboot_endaddr;" \ |
| "era $uboot_startaddr $uboot_endaddr;" \ |
| "cp.b $loadaddr $uboot_startaddr $filesize;" \ |
| "protect on $uboot_startaddr $uboot_endaddr\0" \ |
| "zapenv=protect off $env_startaddr $env_endaddr;" \ |
| "era $env_startaddr $env_endaddr;" \ |
| "protect on $env_startaddr $env_endaddr\0" |
| |
| #define CONFIG_BOOTDELAY 5 |
| |
| #define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) |
| |
| #define CONFIG_ENV_OVERWRITE |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_BSP |
| #define CONFIG_CMD_DIAG |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_ENV |
| #define CONFIG_CMD_FLASH |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_SDRAM |
| |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CFG_LONGHELP /* undef to save memory */ |
| #define CFG_PROMPT "=> " /* Monitor Command Prompt */ |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ |
| |
| #if 1 |
| #define CFG_HUSH_PARSER 1 /* use "hush" command parser */ |
| #endif |
| #ifdef CFG_HUSH_PARSER |
| #define CFG_PROMPT_HUSH_PS2 "> " |
| #endif |
| |
| #define CONFIG_ETHADDR DE:AD:BE:EF:01:01 /* Ethernet address */ |
| #define CONFIG_IPADDR 192.168.193.102 |
| #define CONFIG_NETMASK 255.255.255.248 |
| #define CONFIG_SERVERIP 192.168.193.99 |
| |
| #define CONFIG_STATUS_LED /* Status LED enabled */ |
| #define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */ |
| |
| #define STATUS_LED_BIT 0x00000001 |
| #define STATUS_LED_PERIOD (CFG_HZ / 2) |
| #define STATUS_LED_STATE STATUS_LED_BLINKING |
| #define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */ |
| #define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ |
| |
| #ifndef __ASSEMBLY__ |
| /* LEDs */ |
| typedef unsigned int led_id_t; |
| |
| #define __led_toggle(_msk) \ |
| do { \ |
| *((volatile char *) (CFG_LED_BASE)) ^= (_msk); \ |
| } while(0) |
| |
| #define __led_set(_msk, _st) \ |
| do { \ |
| if ((_st)) \ |
| *((volatile char *) (CFG_LED_BASE)) |= (_msk); \ |
| else \ |
| *((volatile char *) (CFG_LED_BASE)) &= ~(_msk); \ |
| } while(0) |
| |
| #define __led_init(msk, st) __led_set(msk, st) |
| |
| #endif |
| |
| #define CONFIG_MISC_INIT_R |
| #define CFG_LED_BASE 0xFFE80000 |
| |
| /* Print Buffer Size |
| */ |
| #define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) |
| |
| #define CFG_MAXARGS 16 /* max number of command args */ |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ |
| #define CFG_LOAD_ADDR 0x00100000 /* Default load address */ |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CFG_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CFG_SDRAM_BASE 0x00000000 |
| #define CFG_FLASH_BASE 0xFFF00000 |
| |
| #define CFG_RESET_ADDRESS 0xFFF00100 |
| |
| #define CFG_EUMB_ADDR 0xFCE00000 |
| |
| #define CFG_MONITOR_BASE TEXT_BASE |
| |
| #define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ |
| #define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ |
| |
| #define CFG_MEMTEST_START 0x00004000 /* memtest works on */ |
| #define CFG_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */ |
| |
| /* Maximum amount of RAM. |
| */ |
| #define CFG_MAX_RAM_SIZE 0x10000000 |
| |
| #if CFG_MONITOR_BASE >= CFG_FLASH_BASE |
| #undef CFG_RAMBOOT |
| #else |
| #define CFG_RAMBOOT |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area |
| */ |
| |
| /* Size in bytes reserved for initial data |
| */ |
| #define CFG_GBL_DATA_SIZE 128 |
| |
| #define CFG_INIT_RAM_ADDR 0x40000000 |
| #define CFG_INIT_RAM_END 0x1000 |
| #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) |
| |
| /* |
| * NS16550 Configuration |
| */ |
| #define CFG_NS16550 |
| #define CFG_NS16550_SERIAL |
| |
| #define CFG_NS16550_REG_SIZE 1 |
| |
| #define CFG_NS16550_CLK 3686400 |
| |
| #define CFG_NS16550_COM1 0xFFF80000 |
| |
| /* |
| * Low Level Configuration Settings |
| * (address mappings, register initial values, etc.) |
| * You should know what you are doing if you make changes here. |
| * For the detail description refer to the MPC8240 user's manual. |
| */ |
| |
| #define CONFIG_SYS_CLK_FREQ 33000000 |
| #define CFG_HZ 1000 |
| #define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 3 |
| |
| /* Bit-field values for MCCR1. |
| */ |
| #define CFG_ROMNAL 0 |
| #define CFG_ROMFAL 7 |
| |
| /* Bit-field values for MCCR2. |
| */ |
| #define CFG_REFINT 430 /* Refresh interval */ |
| |
| /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. |
| */ |
| #define CFG_BSTOPRE 192 |
| |
| /* Bit-field values for MCCR3. |
| */ |
| #define CFG_REFREC 2 /* Refresh to activate interval */ |
| #define CFG_RDLAT 3 /* Data latancy from read command */ |
| |
| /* Bit-field values for MCCR4. |
| */ |
| #define CFG_PRETOACT 2 /* Precharge to activate interval */ |
| #define CFG_ACTTOPRE 5 /* Activate to Precharge interval */ |
| #define CFG_SDMODE_CAS_LAT 2 /* SDMODE CAS latancy */ |
| #define CFG_SDMODE_WRAP 0 /* SDMODE wrap type */ |
| #define CFG_SDMODE_BURSTLEN 2 /* SDMODE Burst length */ |
| #define CFG_ACTORW 2 |
| #define CFG_REGISTERD_TYPE_BUFFER 1 |
| |
| /* Memory bank settings. |
| * Only bits 20-29 are actually used from these vales to set the |
| * start/end addresses. The upper two bits will always be 0, and the lower |
| * 20 bits will be 0x00000 for a start address, or 0xfffff for an end |
| * address. Refer to the MPC8240 book. |
| */ |
| |
| #define CFG_BANK0_START 0x00000000 |
| #define CFG_BANK0_END (CFG_MAX_RAM_SIZE - 1) |
| #define CFG_BANK0_ENABLE 1 |
| #define CFG_BANK1_START 0x3ff00000 |
| #define CFG_BANK1_END 0x3fffffff |
| #define CFG_BANK1_ENABLE 0 |
| #define CFG_BANK2_START 0x3ff00000 |
| #define CFG_BANK2_END 0x3fffffff |
| #define CFG_BANK2_ENABLE 0 |
| #define CFG_BANK3_START 0x3ff00000 |
| #define CFG_BANK3_END 0x3fffffff |
| #define CFG_BANK3_ENABLE 0 |
| #define CFG_BANK4_START 0x3ff00000 |
| #define CFG_BANK4_END 0x3fffffff |
| #define CFG_BANK4_ENABLE 0 |
| #define CFG_BANK5_START 0x3ff00000 |
| #define CFG_BANK5_END 0x3fffffff |
| #define CFG_BANK5_ENABLE 0 |
| #define CFG_BANK6_START 0x3ff00000 |
| #define CFG_BANK6_END 0x3fffffff |
| #define CFG_BANK6_ENABLE 0 |
| #define CFG_BANK7_START 0x3ff00000 |
| #define CFG_BANK7_END 0x3fffffff |
| #define CFG_BANK7_ENABLE 0 |
| |
| #define CFG_ODCR 0xff |
| |
| #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| |
| #define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) |
| |
| #define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) |
| #define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) |
| |
| #define CFG_IBAT3L (0xFC000000 | BATL_PP_10 | BATL_CACHEINHIBIT) |
| #define CFG_IBAT3U (0xFC000000 | BATU_BL_64M | BATU_VS | BATU_VP) |
| |
| #define CFG_DBAT0L CFG_IBAT0L |
| #define CFG_DBAT0U CFG_IBAT0U |
| #define CFG_DBAT1L CFG_IBAT1L |
| #define CFG_DBAT1U CFG_IBAT1U |
| #define CFG_DBAT2L CFG_IBAT2L |
| #define CFG_DBAT2U CFG_IBAT2U |
| #define CFG_DBAT3L CFG_IBAT3L |
| #define CFG_DBAT3U CFG_IBAT3U |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CFG_MAX_FLASH_BANKS 1 /* Max number of flash banks */ |
| #define CFG_MAX_FLASH_SECT 256 /* Max number of sectors in one bank */ |
| |
| #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| /* |
| * Init Memory Controller: |
| * |
| * BR0/1 and OR0/1 (FLASH) |
| */ |
| |
| #define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */ |
| #define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ |
| |
| /* Warining: environment is not EMBEDDED in the U-Boot code. |
| * It's stored in flash separately. |
| */ |
| #define CFG_ENV_IS_IN_FLASH 1 |
| #define CFG_ENV_ADDR 0xFFF70000 |
| #define CFG_ENV_SIZE 0x4000 /* Size of the Environment */ |
| #define CFG_ENV_OFFSET 0 /* starting right at the beginning */ |
| #define CFG_ENV_SECT_SIZE 0x40000 /* Size of the Environment Sector */ |
| |
| /*----------------------------------------------------------------------- |
| * Cache Configuration |
| */ |
| #define CFG_CACHELINE_SIZE 32 |
| #if defined(CONFIG_CMD_KGDB) |
| # define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| #endif |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_PCI /* include pci support */ |
| #define CONFIG_PCI_PNP /* we need Plug 'n Play */ |
| #define CONFIG_NET_MULTI /* Multi ethernet cards support */ |
| #define CONFIG_TULIP |
| #define CONFIG_EEPRO100 |
| #define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ |
| #endif /* __CONFIG_H */ |