blob: 068fc7db347fc01f2e8cc11ca3a065f41eaacff7 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Board configuration file for Phytec phyBOARD-i.MX6ULL-Segin SBC
* Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
*
* Based on include/configs/xpress.h:
* Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
*/
#ifndef __PCL063_ULL_H
#define __PCL063_ULL_H
#include <linux/sizes.h>
#include <linux/stringify.h>
#include "mx6_common.h"
/* SPL options */
#include "imx6_spl.h"
#define CONFIG_SYS_FSL_USDHC_NUM 2
/* Environment settings */
/* Environment in SD */
#define MMC_ROOTFS_DEV 0
#define MMC_ROOTFS_PART 2
/* Console configs */
#define CONFIG_MXC_UART_BASE UART1_BASE
/* MMC Configs */
#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
/* I2C configs */
/* Miscellaneous configurable options */
/* Physical Memory Map */
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define PHYS_SDRAM_SIZE SZ_256M
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* NAND */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x40000000
/* USB Configs */
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#define ENV_MMC \
"mmcdev=" __stringify(MMC_ROOTFS_DEV) "\0" \
"mmcpart=" __stringify(MMC_ROOTFS_PART) "\0" \
"fitpart=1\0" \
"bootdelay=3\0" \
"silent=1\0" \
"optargs=rw rootwait\0" \
"mmcautodetect=yes\0" \
"mmcrootfstype=ext4\0" \
"mmcfit_name=fitImage\0" \
"mmcloadfit=fatload mmc ${mmcdev}:${fitpart} ${fit_addr} " \
"${mmcfit_name}\0" \
"mmcargs=setenv bootargs " \
"root=/dev/mmcblk${mmcdev}p${mmcpart} ${optargs} " \
"console=${console} rootfstype=${mmcrootfstype}\0" \
"mmc_mmc_fit=run mmcloadfit;run mmcargs addcon; bootm ${fit_addr}\0" \
/* Default environment */
#define CONFIG_EXTRA_ENV_SETTINGS \
"fdt_high=0xffffffff\0" \
"console=ttymxc0,115200n8\0" \
"addcon=setenv bootargs ${bootargs} console=${console},${baudrate}\0" \
"fit_addr=0x82000000\0" \
ENV_MMC
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
func(MMC, mmc, 1) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#endif /* __PCL063_ULL_H */