blob: 88ee59259caf1ed6cafa708bf2fe6bf4b66b6d2e [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2011, Stefano Babic <sbabic@denx.de>
*
* (C) Copyright 2008-2010 Freescale Semiconductor, Inc.
*
* Configuration for the woodburn board.
*/
#ifndef __WOODBURN_COMMON_CONFIG_H
#define __WOODBURN_COMMON_CONFIG_H
#include <asm/arch/imx-regs.h>
/* High Level Configuration Options */
#define CONFIG_MX35
#define CONFIG_MX35_HCLK_FREQ 24000000
#define CONFIG_SYS_FSL_CLK
#define CONFIG_SYS_DCACHE_OFF
#define CONFIG_MACH_TYPE MACH_TYPE_FLEA3
/* This is required to setup the ESDC controller */
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_REVISION_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024)
/*
* Hardware drivers
*/
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
#define CONFIG_SYS_SPD_BUS_NUM 0
/* PMIC Controller */
#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_FSL
#define CONFIG_POWER_FSL_MC13892
#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x8
#define CONFIG_RTC_MC13XXX
/* mmc driver */
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_SYS_FSL_ESDHC_NUM 1
/*
* UART (console)
*/
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART1_BASE
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
/*
* Command definition
*/
#define CONFIG_NET_RETRY_COUNT 100
#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */
/*
* Ethernet on SOC (FEC)
*/
#define CONFIG_FEC_MXC
#define IMX_FEC_BASE FEC_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1
#define CONFIG_MII
#define CONFIG_DISCOVER_PHY
#define CONFIG_ARP_TIMEOUT 200UL
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x10000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
/*
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 CSD0_BASE_ADDR
#define PHYS_SDRAM_1_SIZE (256 * 1024 * 1024)
#define CONFIG_SYS_SDRAM_BASE CSD0_BASE_ADDR
#define CONFIG_SYS_GBL_DATA_OFFSET (LOW_LEVEL_SRAM_STACK - \
IRAM_BASE_ADDR - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR (IRAM_BASE_ADDR + \
CONFIG_SYS_GBL_DATA_OFFSET)
/*
* MTD Command for mtdparts
*/
#define CONFIG_FLASH_CFI_MTD
/*
* FLASH and environment organization
*/
#define CONFIG_SYS_FLASH_BASE CS0_BASE_ADDR
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
/* Monitor at beginning of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
#define CONFIG_ENV_SECT_SIZE (128 * 1024)
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
CONFIG_SYS_MONITOR_LEN)
/*
* CFI FLASH driver setup
*/
#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */
#define CONFIG_FLASH_CFI_DRIVER
/* A non-standard buffered write algorithm */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* faster */
#define CONFIG_SYS_FLASH_PROTECTION /* Use hardware sector protection */
/*
* NAND FLASH driver setup
*/
#define CONFIG_NAND_MXC_V1_1
#define CONFIG_MXC_NAND_REGS_BASE (NFC_BASE_ADDR)
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE (NFC_BASE_ADDR)
#define CONFIG_MXC_NAND_HWECC
#define CONFIG_SYS_NAND_LARGEPAGE
#define CONFIG_SYS_NAND_ONFI_DETECTION
/*
* Default environment and default scripts
* to update uboot and load kernel
*/
#define CONFIG_HOSTNAME "woodburn"
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip_sta=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \
"addip=if test -n ${ipdyn};then run addip_dyn;" \
"else run addip_sta;fi\0" \
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
"addtty=setenv bootargs ${bootargs}" \
" console=ttymxc0,${baudrate}\0" \
"addmisc=setenv bootargs ${bootargs} ${misc}\0" \
"loadaddr=80800000\0" \
"kernel_addr_r=80800000\0" \
"hostname=" CONFIG_HOSTNAME "\0" \
"bootfile=" CONFIG_HOSTNAME "/uImage\0" \
"ramdisk_file=" CONFIG_HOSTNAME "/uRamdisk\0" \
"flash_self=run ramargs addip addtty addmtd addmisc;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
"bootm ${kernel_addr}\0" \
"net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
"run nfsargs addip addtty addmtd addmisc;" \
"bootm ${kernel_addr_r}\0" \
"net_self_load=tftp ${kernel_addr_r} ${bootfile};" \
"tftp ${ramdisk_addr_r} ${ramdisk_file};\0" \
"net_self=if run net_self_load;then " \
"run ramargs addip addtty addmtd addmisc;" \
"bootm ${kernel_addr_r} ${ramdisk_addr_r};" \
"else echo Images not loades;fi\0" \
"u-boot=" CONFIG_HOSTNAME "/u-boot.bin\0" \
"load=tftp ${loadaddr} ${u-boot}\0" \
"uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0" \
"update=protect off ${uboot_addr} +80000;" \
"erase ${uboot_addr} +80000;" \
"cp.b ${loadaddr} ${uboot_addr} ${filesize}\0" \
"upd=if run load;then echo Updating u-boot;if run update;" \
"then echo U-Boot updated;" \
"else echo Error updating u-boot !;" \
"echo Board without bootloader !!;" \
"fi;" \
"else echo U-Boot not downloaded..exiting;fi\0" \
"bootcmd=run net_nfs\0"
#endif /* __CONFIG_H */