| /* |
| * (C) Copyright 2013 |
| * Heiko Schocher, DENX Software Engineering, hs@denx.de. |
| * |
| * Based on: |
| * Copyright (c) 2011 IDS GmbH, Germany |
| * Sergej Stepanov <ste@ids.de> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| */ |
| #define CONFIG_MPC831x |
| #define CONFIG_MPC8313 |
| |
| #define CONFIG_FSL_ELBC |
| |
| #define CONFIG_MISC_INIT_R |
| |
| #define CONFIG_BOOT_RETRY_TIME 900 |
| #define CONFIG_BOOT_RETRY_MIN 30 |
| #define CONFIG_RESET_TO_RETRY |
| |
| #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ |
| #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN |
| |
| #define CONFIG_SYS_IMMR 0xF0000000 |
| |
| #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ |
| #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ |
| |
| /* |
| * Hardware Reset Configuration Word |
| * if CLKIN is 66.000MHz, then |
| * CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz |
| */ |
| #define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\ |
| HRCWL_DDR_TO_SCB_CLK_2X1 |\ |
| HRCWL_CSB_TO_CLKIN_2X1 |\ |
| HRCWL_CORE_TO_CSB_2X1) |
| |
| #define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST |\ |
| HRCWH_CORE_ENABLE |\ |
| HRCWH_FROM_0XFFF00100 |\ |
| HRCWH_BOOTSEQ_DISABLE |\ |
| HRCWH_SW_WATCHDOG_DISABLE |\ |
| HRCWH_ROM_LOC_LOCAL_8BIT |\ |
| HRCWH_RL_EXT_LEGACY |\ |
| HRCWH_TSEC1M_IN_MII |\ |
| HRCWH_TSEC2M_IN_MII |\ |
| HRCWH_BIG_ENDIAN) |
| |
| #define CONFIG_SYS_SICRH 0x00000000 |
| #define CONFIG_SYS_SICRL (SICRL_LBC | SICRL_SPI_D) |
| |
| #define CONFIG_HWCONFIG |
| |
| #define CONFIG_SYS_HID0_INIT 0x000000000 |
| #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK |\ |
| HID0_ENABLE_INSTRUCTION_CACHE |\ |
| HID0_DISABLE_DYNAMIC_POWER_MANAGMENT) |
| |
| #define CONFIG_SYS_HID2 (HID2_HBE | 0x00020000) |
| |
| /* |
| * Definitions for initial stack pointer and data area (in DCACHE ) |
| */ |
| #define CONFIG_SYS_INIT_RAM_LOCK |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in DPRAM */ |
| #define CONFIG_SYS_GBL_DATA_SIZE 0x100 |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \ |
| - CONFIG_SYS_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /* |
| * Local Bus LCRR and LBCR regs |
| */ |
| #define CONFIG_SYS_LCRR_EADC LCRR_EADC_1 |
| #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 |
| #define CONFIG_SYS_LBC_LBCR (0x00040000 |\ |
| (0xFF << LBCR_BMT_SHIFT) |\ |
| 0xF) |
| |
| #define CONFIG_SYS_LBC_MRTPR 0x20000000 |
| |
| /* |
| * Internal Definitions |
| */ |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_SYS_DDR_BASE 0x00000000 |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE |
| #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE |
| |
| /* |
| * Manually set up DDR parameters, |
| * as this board has not the SPD connected to I2C. |
| */ |
| #define CONFIG_SYS_DDR_SIZE 256 /* MB */ |
| #define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN |\ |
| 0x00010000 |\ |
| CSCONFIG_ROW_BIT_13 |\ |
| CSCONFIG_COL_BIT_10) |
| |
| #define CONFIG_SYS_DDR_CONFIG_256 (CONFIG_SYS_DDR_CONFIG | \ |
| CSCONFIG_BANK_BIT_3) |
| |
| #define CONFIG_SYS_DDR_TIMING_3 (1 << 16) /* ext refrec */ |
| #define CONFIG_SYS_DDR_TIMING_0 ((3 << TIMING_CFG0_RWT_SHIFT) |\ |
| (3 << TIMING_CFG0_WRT_SHIFT) |\ |
| (3 << TIMING_CFG0_RRT_SHIFT) |\ |
| (3 << TIMING_CFG0_WWT_SHIFT) |\ |
| (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\ |
| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\ |
| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ |
| (2 << TIMING_CFG0_MRS_CYC_SHIFT)) |
| #define CONFIG_SYS_DDR_TIMING_1 ((4 << TIMING_CFG1_PRETOACT_SHIFT) |\ |
| (12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\ |
| (4 << TIMING_CFG1_ACTTORW_SHIFT) |\ |
| (7 << TIMING_CFG1_CASLAT_SHIFT) |\ |
| (4 << TIMING_CFG1_REFREC_SHIFT) |\ |
| (4 << TIMING_CFG1_WRREC_SHIFT) |\ |
| (2 << TIMING_CFG1_ACTTOACT_SHIFT) |\ |
| (2 << TIMING_CFG1_WRTORD_SHIFT)) |
| #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\ |
| (5 << TIMING_CFG2_CPO_SHIFT) |\ |
| (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\ |
| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\ |
| (0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\ |
| (1 << TIMING_CFG2_CKE_PLS_SHIFT) |\ |
| (6 << TIMING_CFG2_FOUR_ACT_SHIFT)) |
| |
| #define CONFIG_SYS_DDR_INTERVAL ((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\ |
| (0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) |
| |
| #define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN |\ |
| SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\ |
| SDRAM_CFG_DBW_32 |\ |
| SDRAM_CFG_SDRAM_TYPE_DDR2) |
| |
| #define CONFIG_SYS_SDRAM_CFG2 0x00401000 |
| #define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) |\ |
| (0x0242 << SDRAM_MODE_SD_SHIFT)) |
| #define CONFIG_SYS_DDR_MODE_2 0x00000000 |
| #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075 |
| #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN |\ |
| DDRCDR_PZ_NOMZ |\ |
| DDRCDR_NZ_NOMZ |\ |
| DDRCDR_ODT |\ |
| DDRCDR_M_ODR |\ |
| DDRCDR_Q_DRN) |
| |
| /* |
| * on-board devices |
| */ |
| #define CONFIG_TSEC1 |
| #define CONFIG_TSEC2 |
| #define CONFIG_HARD_SPI |
| |
| /* |
| * NOR FLASH setup |
| */ |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT |
| #define CONFIG_FLASH_SHOW_PROGRESS 50 |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE |
| |
| #define CONFIG_SYS_FLASH_BASE 0xFF800000 |
| #define CONFIG_SYS_FLASH_SIZE 8 |
| #define CONFIG_SYS_FLASH_PROTECTION |
| |
| #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 |
| |
| #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\ |
| BR_PS_8 |\ |
| BR_MS_GPCM |\ |
| BR_V) |
| |
| #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\ |
| OR_GPCM_SCY_10 |\ |
| OR_GPCM_EHTR |\ |
| OR_GPCM_TRLX |\ |
| OR_GPCM_CSNT |\ |
| OR_GPCM_EAD) |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 |
| #define CONFIG_SYS_MAX_FLASH_SECT 128 |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 |
| |
| /* |
| * NAND FLASH setup |
| */ |
| #define CONFIG_SYS_NAND_BASE 0xE1000000 |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_MAX_CHIPS 1 |
| #define CONFIG_NAND_FSL_ELBC |
| #define CONFIG_SYS_NAND_PAGE_SIZE (2048) |
| #define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) |
| #define NAND_CACHE_PAGES 64 |
| |
| #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE |
| #define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E |
| #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM |
| #define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM |
| |
| #define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_NAND_BASE) |\ |
| (2<<BR_DECC_SHIFT) |\ |
| BR_PS_8 |\ |
| BR_MS_FCM |\ |
| BR_V) |
| |
| #define CONFIG_SYS_OR1_PRELIM (0xFFFF8000 |\ |
| OR_FCM_PGS |\ |
| OR_FCM_CSCT |\ |
| OR_FCM_CST |\ |
| OR_FCM_CHT |\ |
| OR_FCM_SCY_4 |\ |
| OR_FCM_TRLX |\ |
| OR_FCM_EHTR |\ |
| OR_FCM_RST) |
| |
| /* |
| * MRAM setup |
| */ |
| #define CONFIG_SYS_MRAM_BASE 0xE2000000 |
| #define CONFIG_SYS_MRAM_SIZE 0x20000 /* 128 Kb */ |
| #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_MRAM_BASE |
| #define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 /* 128 Kb */ |
| |
| #define CONFIG_SYS_OR_TIMING_MRAM |
| |
| #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_MRAM_BASE |\ |
| BR_PS_8 |\ |
| BR_MS_GPCM |\ |
| BR_V) |
| |
| #define CONFIG_SYS_OR2_PRELIM 0xFFFE0C74 |
| |
| /* |
| * CPLD setup |
| */ |
| #define CONFIG_SYS_CPLD_BASE 0xE3000000 |
| #define CONFIG_SYS_CPLD_SIZE 0x8000 |
| #define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_CPLD_BASE |
| #define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000E |
| |
| #define CONFIG_SYS_OR_TIMING_MRAM |
| |
| #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_CPLD_BASE |\ |
| BR_PS_8 |\ |
| BR_MS_GPCM |\ |
| BR_V) |
| |
| #define CONFIG_SYS_OR3_PRELIM 0xFFFF8814 |
| |
| /* |
| * HW-Watchdog |
| */ |
| #define CONFIG_WATCHDOG 1 |
| #define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF |
| |
| /* |
| * I2C setup |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_FSL |
| #define CONFIG_SYS_FSL_I2C_SPEED 400000 |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 |
| #define CONFIG_RTC_PCF8563 |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x51 |
| |
| /* |
| * SPI setup |
| */ |
| #ifdef CONFIG_HARD_SPI |
| #define CONFIG_SYS_GPIO1_PRELIM |
| #define CONFIG_SYS_GPIO1_DIR 0x00000001 |
| #define CONFIG_SYS_GPIO1_DAT 0x00000001 |
| #endif |
| |
| /* |
| * Ethernet setup |
| */ |
| #ifdef CONFIG_TSEC1 |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_TSEC1_NAME "TSEC0" |
| #define CONFIG_SYS_TSEC1_OFFSET 0x24000 |
| #define TSEC1_PHY_ADDR 0x1 |
| #define TSEC1_FLAGS TSEC_GIGABIT |
| #define TSEC1_PHYIDX 0 |
| #endif |
| |
| #ifdef CONFIG_TSEC2 |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_TSEC2_NAME "TSEC1" |
| #define CONFIG_SYS_TSEC2_OFFSET 0x25000 |
| #define TSEC2_PHY_ADDR 0x3 |
| #define TSEC2_FLAGS TSEC_GIGABIT |
| #define TSEC2_PHYIDX 0 |
| #endif |
| #define CONFIG_ETHPRIME "TSEC1" |
| |
| /* |
| * Serial Port |
| */ |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) |
| #define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2) |
| |
| #define CONFIG_HAS_FSL_DR_USB |
| #define CONFIG_SYS_SCCR_USBDRCM 3 |
| |
| /* |
| * BAT's |
| */ |
| #define CONFIG_HIGH_BATS |
| |
| /* DDR @ 0x00000000 */ |
| #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE |\ |
| BATL_PP_10) |
| #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE |\ |
| BATU_BL_256M |\ |
| BATU_VS |\ |
| BATU_VP) |
| #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L |
| #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U |
| |
| /* Initial RAM @ 0xFD000000 */ |
| #define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR |\ |
| BATL_PP_10 |\ |
| BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR |\ |
| BATU_BL_256K |\ |
| BATU_VS |\ |
| BATU_VP) |
| #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L |
| #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U |
| |
| /* FLASH @ 0xFF800000 */ |
| #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE |\ |
| BATL_PP_10 |\ |
| BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE |\ |
| BATU_BL_8M |\ |
| BATU_VS |\ |
| BATU_VP) |
| #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE |\ |
| BATL_PP_10 |\ |
| BATL_CACHEINHIBIT |\ |
| BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U |
| |
| #define CONFIG_SYS_IBAT3L (0) |
| #define CONFIG_SYS_IBAT3U (0) |
| #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L |
| #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U |
| |
| #define CONFIG_SYS_IBAT4L (0) |
| #define CONFIG_SYS_IBAT4U (0) |
| #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L |
| #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U |
| |
| /* IMMRBAR @ 0xF0000000 */ |
| #define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR |\ |
| BATL_PP_10 |\ |
| BATL_CACHEINHIBIT |\ |
| BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR |\ |
| BATU_BL_128M |\ |
| BATU_VS |\ |
| BATU_VP) |
| #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L |
| #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U |
| |
| /* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */ |
| #define CONFIG_SYS_IBAT6L (0xE0000000 |\ |
| BATL_PP_10 |\ |
| BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT6U (0xE0000000 |\ |
| BATU_BL_256M |\ |
| BATU_VS |\ |
| BATU_VP) |
| #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L |
| #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U |
| |
| #define CONFIG_SYS_IBAT7L (0) |
| #define CONFIG_SYS_IBAT7U (0) |
| #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L |
| #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U |
| |
| /* |
| * U-Boot environment setup |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| |
| /* |
| * The reserved memory |
| */ |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_MONITOR_LEN (768 * 1024) |
| #define CONFIG_SYS_MALLOC_LEN (8 * 1024 * 1024) |
| |
| /* |
| * Environment Configuration |
| */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ |
| + CONFIG_SYS_MONITOR_LEN) |
| #define CONFIG_ENV_SIZE 0x20000 |
| #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) |
| |
| #define CONFIG_NETDEV eth1 |
| #define CONFIG_HOSTNAME "ids8313" |
| #define CONFIG_ROOTPATH "/opt/eldk-4.2/ppc_6xx" |
| #define CONFIG_BOOTFILE "ids8313/uImage" |
| #define CONFIG_UBOOTPATH "ids8313/u-boot.bin" |
| #define CONFIG_FDTFILE "ids8313/ids8313.dtb" |
| #define CONFIG_LOADADDR 0x400000 |
| #define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo" |
| |
| /* Initial Memory map for Linux*/ |
| #define CONFIG_SYS_BOOTMAPSZ (256 << 20) |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_CBSIZE 1024 |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00001000 |
| #define CONFIG_SYS_MEMTEST_END 0x00C00000 |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x100000 |
| #define CONFIG_MII |
| #define CONFIG_LOADS_ECHO |
| #define CONFIG_TIMESTAMP |
| #define CONFIG_PREBOOT "echo;" \ |
| "echo Type \\\"run nfsboot\\\" " \ |
| "to mount root filesystem over NFS;echo" |
| #define CONFIG_BOOTCOMMAND "run boot_cramfs" |
| #undef CONFIG_SYS_LOADS_BAUD_CHANGE |
| |
| #define CONFIG_JFFS2_NAND |
| #define CONFIG_JFFS2_DEV "0" |
| |
| /* mtdparts command line support */ |
| #define CONFIG_FLASH_CFI_MTD |
| #define CONFIG_MTD_DEVICE |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=" __stringify(CONFIG_NETDEV) "\0" \ |
| "ethprime=TSEC1\0" \ |
| "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ |
| "tftpflash=tftpboot ${loadaddr} ${uboot}; " \ |
| "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ |
| " +${filesize}; " \ |
| "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ |
| " +${filesize}; " \ |
| "cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \ |
| " ${filesize}; " \ |
| "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ |
| " +${filesize}; " \ |
| "cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \ |
| " ${filesize}\0" \ |
| "console=ttyS0\0" \ |
| "fdtaddr=0x780000\0" \ |
| "kernel_addr=ff800000\0" \ |
| "fdtfile=" __stringify(CONFIG_FDTFILE) "\0" \ |
| "setbootargs=setenv bootargs " \ |
| "root=${rootdev} rw console=${console}," \ |
| "${baudrate} ${othbootargs}\0" \ |
| "setipargs=setenv bootargs root=${rootdev} rw " \ |
| "nfsroot=${serverip}:${rootpath} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:" \ |
| "${netmask}:${hostname}:${netdev}:off " \ |
| "console=${console},${baudrate} ${othbootargs}\0" \ |
| "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ |
| "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \ |
| "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \ |
| "\0" |
| |
| #define CONFIG_NFSBOOTCOMMAND \ |
| "setenv rootdev /dev/nfs;" \ |
| "run setipargs;run addmtd;" \ |
| "tftp ${loadaddr} ${bootfile};" \ |
| "tftp ${fdtaddr} ${fdtfile};" \ |
| "fdt addr ${fdtaddr};" \ |
| "bootm ${loadaddr} - ${fdtaddr}" |
| |
| /* UBI Support */ |
| #define CONFIG_MTD_PARTITIONS |
| |
| #endif /* __CONFIG_H */ |