include/configs/ls1046a_common.h - platform/external/u-boot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2016 Freescale Semiconductor
  * Copyright 2019-2021 NXP
  */

 #ifndef __LS1046A_COMMON_H
 #define __LS1046A_COMMON_H

 /* SPL build */
 #ifdef CONFIG_SPL_BUILD
 #define SPL_NO_QBMAN
 #define SPL_NO_FMAN
 #define SPL_NO_ENV
 #define SPL_NO_MISC
 #define SPL_NO_QSPI
 #define SPL_NO_USB
 #define SPL_NO_SATA
 #endif
 #if defined(CONFIG_SPL_BUILD) && \
 	(defined(CONFIG_NAND_BOOT) || defined(CONFIG_QSPI_BOOT))
 #define SPL_NO_MMC
 #endif
 #if defined(CONFIG_SPL_BUILD)		&& \
 	!defined(CONFIG_SPL_FSL_LS_PPA)
 #define SPL_NO_IFC
 #endif

 #define CONFIG_REMAKE_ELF
 #define CONFIG_GICV2

 #include <asm/arch/config.h>
 #include <asm/arch/stream_id_lsch2.h>

 /* Link Definitions */
 #ifdef CONFIG_TFABOOT
 #define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_TEXT_BASE
 #else
 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
 #endif

 #define CONFIG_SKIP_LOWLEVEL_INIT

 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000
 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_SYS_DDR_BLOCK2_BASE      0x880000000ULL

 #define CPU_RELEASE_ADDR               secondary_boot_addr

 /* Generic Timer Definitions */
 #define COUNTER_FREQUENCY		25000000	/* 25MHz */

 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 1024 * 1024)

 /* Serial Port */
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())

 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

 /* SD boot SPL */
 #ifdef CONFIG_SD_BOOT
 #define CONFIG_SPL_MAX_SIZE		0x1f000		/* 124 KiB */
 #define CONFIG_SPL_STACK		0x10020000
 #define CONFIG_SPL_PAD_TO		0x21000		/* 132 KiB */
 #define CONFIG_SPL_BSS_START_ADDR	0x8f000000
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000
 #define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
 					CONFIG_SPL_BSS_MAX_SIZE)
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000

 #ifdef CONFIG_NXP_ESBC
 #define CONFIG_U_BOOT_HDR_SIZE				(16 << 10)
 /*
  * HDR would be appended at end of image and copied to DDR along
  * with U-Boot image. Here u-boot max. size is 512K. So if binary
  * size increases then increase this size in case of secure boot as
  * it uses raw u-boot image instead of fit image.
  */
 #define CONFIG_SYS_MONITOR_LEN		(0x100000 + CONFIG_U_BOOT_HDR_SIZE)
 #else
 #define CONFIG_SYS_MONITOR_LEN		0x100000
 #endif /* ifdef CONFIG_NXP_ESBC */
 #endif

 #if defined(CONFIG_QSPI_BOOT) && defined(CONFIG_SPL)
 #define CONFIG_SPL_TARGET		"spl/u-boot-spl.pbl"
 #define CONFIG_SPL_MAX_SIZE		0x1f000
 #define CONFIG_SPL_STACK		0x10020000
 #define CONFIG_SPL_PAD_TO		0x20000
 #define CONFIG_SPL_BSS_START_ADDR	0x8f000000
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000
 #define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
 					CONFIG_SPL_BSS_MAX_SIZE)
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
 #define CONFIG_SYS_MONITOR_LEN		0x100000
 #endif

 /* NAND SPL */
 #ifdef CONFIG_NAND_BOOT
 #define CONFIG_SPL_PBL_PAD
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 #define CONFIG_SPL_ENV_SUPPORT
 #define CONFIG_SPL_WATCHDOG_SUPPORT
 #define CONFIG_SPL_I2C_SUPPORT
 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT

 #define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
 #define CONFIG_SPL_MAX_SIZE		0x17000		/* 90 KiB */
 #define CONFIG_SPL_STACK		0x1001f000
 #define CONFIG_SYS_NAND_U_BOOT_DST	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE

 #define CONFIG_SPL_BSS_START_ADDR	0x8f000000
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000
 #define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
 					CONFIG_SPL_BSS_MAX_SIZE)
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
 #define CONFIG_SYS_MONITOR_LEN		0xa0000
 #endif

 /* GPIO */
 #ifdef CONFIG_DM_GPIO
 #ifndef CONFIG_MPC8XXX_GPIO
 #define CONFIG_MPC8XXX_GPIO
 #endif
 #endif

 /* I2C */
 #if !CONFIG_IS_ENABLED(DM_I2C)
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
 #define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
 #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
 #define CONFIG_SYS_I2C_MXC_I2C4		/* enable I2C bus 4 */
 #else
 #define CONFIG_I2C_SET_DEFAULT_BUS_NUM
 #define CONFIG_I2C_DEFAULT_BUS_NUMBER 0
 #endif

 /* PCIe */
 #define CONFIG_PCIE1		/* PCIE controller 1 */
 #define CONFIG_PCIE2		/* PCIE controller 2 */
 #define CONFIG_PCIE3		/* PCIE controller 3 */

 #ifdef CONFIG_PCI
 #define CONFIG_PCI_SCAN_SHOW
 #endif

 /* SATA */
 #ifndef SPL_NO_SATA
 #define CONFIG_SCSI_AHCI_PLAT

 #define CONFIG_SYS_SATA				AHCI_BASE_ADDR

 #define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
 #define CONFIG_SYS_SCSI_MAX_LUN			1
 #define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 						CONFIG_SYS_SCSI_MAX_LUN)
 #endif

 /* FMan ucode */
 #ifndef SPL_NO_FMAN
 #define CONFIG_SYS_DPAA_FMAN
 #ifdef CONFIG_SYS_DPAA_FMAN
 #define CONFIG_SYS_FM_MURAM_SIZE	0x60000
 #endif

 #ifdef CONFIG_TFABOOT
 #define CONFIG_SYS_FMAN_FW_ADDR		0x900000
 #else
 #ifdef CONFIG_SD_BOOT
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 18432(0x4800).
  */
 #define CONFIG_SYS_FMAN_FW_ADDR		(512 * 0x4800)
 #elif defined(CONFIG_QSPI_BOOT)
 #define CONFIG_SYS_FMAN_FW_ADDR		0x40900000
 #elif defined(CONFIG_NAND_BOOT)
 #define CONFIG_SYS_FMAN_FW_ADDR		(36 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #else
 #define CONFIG_SYS_FMAN_FW_ADDR		0x60900000
 #endif
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 #endif

 /* Miscellaneous configurable options */
 #define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)

 #define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE		128

 #ifndef CONFIG_SPL_BUILD
 #define BOOT_TARGET_DEVICES(func) \
 	func(SCSI, scsi, 0) \
 	func(MMC, mmc, 0) \
 	func(USB, usb, 0) \
 	func(DHCP, dhcp, na)
 #include <config_distro_bootcmd.h>
 #endif

 #if defined(CONFIG_TARGET_LS1046AFRWY)
 #define LS1046A_BOOT_SRC_AND_HDR\
 	"boot_scripts=ls1046afrwy_boot.scr\0"	\
 	"boot_script_hdr=hdr_ls1046afrwy_bs.out\0"
 #elif defined(CONFIG_TARGET_LS1046AQDS)
 #define LS1046A_BOOT_SRC_AND_HDR\
 	"boot_scripts=ls1046aqds_boot.scr\0"	\
 	"boot_script_hdr=hdr_ls1046aqds_bs.out\0"
 #else
 #define LS1046A_BOOT_SRC_AND_HDR\
 	"boot_scripts=ls1046ardb_boot.scr\0"	\
 	"boot_script_hdr=hdr_ls1046ardb_bs.out\0"
 #endif
 #ifndef SPL_NO_MISC
 /* Initial environment variables */
 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
 	"ramdisk_addr=0x800000\0"		\
 	"ramdisk_size=0x2000000\0"		\
 	"bootm_size=0x10000000\0"		\
 	"fdt_addr=0x64f00000\0"                 \
 	"kernel_addr=0x61000000\0"              \
 	"scriptaddr=0x80000000\0"               \
 	"scripthdraddr=0x80080000\0"		\
 	"fdtheader_addr_r=0x80100000\0"         \
 	"kernelheader_addr_r=0x80200000\0"      \
 	"load_addr=0xa0000000\0"            \
 	"kernel_addr_r=0x81000000\0"            \
 	"fdt_addr_r=0x90000000\0"               \
 	"ramdisk_addr_r=0xa0000000\0"           \
 	"kernel_start=0x1000000\0"		\
 	"kernelheader_start=0x600000\0"		\
 	"kernel_load=0xa0000000\0"		\
 	"kernel_size=0x2800000\0"		\
 	"kernelheader_size=0x40000\0"		\
 	"kernel_addr_sd=0x8000\0"		\
 	"kernel_size_sd=0x14000\0"		\
 	"kernelhdr_addr_sd=0x3000\0"		\
 	"kernelhdr_size_sd=0x10\0"		\
 	"console=ttyS0,115200\0"                \
 	 CONFIG_MTDPARTS_DEFAULT "\0"		\
 	BOOTENV					\
 	LS1046A_BOOT_SRC_AND_HDR		\
 	"scan_dev_for_boot_part="               \
 		"part list ${devtype} ${devnum} devplist; "   \
 		"env exists devplist || setenv devplist 1; "  \
 		"for distro_bootpart in ${devplist}; do "     \
 		  "if fstype ${devtype} "                  \
 			"${devnum}:${distro_bootpart} "      \
 			"bootfstype; then "                  \
 			"run scan_dev_for_boot; "            \
 		  "fi; "                                   \
 		"done\0"                                   \
 	"boot_a_script="				  \
 		"load ${devtype} ${devnum}:${distro_bootpart} "  \
 			"${scriptaddr} ${prefix}${script}; "    \
 		"env exists secureboot && load ${devtype} "     \
 			"${devnum}:${distro_bootpart} "		\
 			"${scripthdraddr} ${prefix}${boot_script_hdr}; " \
 			"env exists secureboot "	\
 			"&& esbc_validate ${scripthdraddr};"	\
 		"source ${scriptaddr}\0"	  \
 	"qspi_bootcmd=echo Trying load from qspi..;"      \
 		"sf probe && sf read $load_addr "         \
 		"$kernel_start $kernel_size; env exists secureboot "	\
 		"&& sf read $kernelheader_addr_r $kernelheader_start "	\
 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 		"bootm $load_addr#$board\0"		\
 	"nand_bootcmd=echo Trying load from nand..;"      \
 		"nand info; nand read $load_addr "         \
 		"$kernel_start $kernel_size; env exists secureboot "	\
 		"&& nand read $kernelheader_addr_r $kernelheader_start " \
 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 		"bootm $load_addr#$board\0"		\
 	"nor_bootcmd=echo Trying load from nor..;"	\
 		"cp.b $kernel_addr $load_addr "		\
 		"$kernel_size; env exists secureboot "	\
 		"&& cp.b $kernelheader_addr $kernelheader_addr_r "	\
 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 		"bootm $load_addr#$board\0"	\
 	"sd_bootcmd=echo Trying load from SD ..;"	\
 		"mmcinfo; mmc read $load_addr "		\
 		"$kernel_addr_sd $kernel_size_sd && "	\
 		"env exists secureboot && mmc read $kernelheader_addr_r "		\
 		"$kernelhdr_addr_sd $kernelhdr_size_sd "		\
 		" && esbc_validate ${kernelheader_addr_r};"	\
 		"bootm $load_addr#$board\0"

 #endif

 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */

 #define CONFIG_SYS_MAXARGS		64	/* max command args */

 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */

 #include <asm/arch/soc.h>

 #endif /* __LS1046A_COMMON_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright 2016 Freescale Semiconductor
	* Copyright 2019-2021 NXP
	*/

	#ifndef __LS1046A_COMMON_H
	#define __LS1046A_COMMON_H

	/* SPL build */
	#ifdef CONFIG_SPL_BUILD
	#define SPL_NO_QBMAN
	#define SPL_NO_FMAN
	#define SPL_NO_ENV
	#define SPL_NO_MISC
	#define SPL_NO_QSPI
	#define SPL_NO_USB
	#define SPL_NO_SATA
	#endif
	#if defined(CONFIG_SPL_BUILD) && \
	(defined(CONFIG_NAND_BOOT) \|\| defined(CONFIG_QSPI_BOOT))
	#define SPL_NO_MMC
	#endif
	#if defined(CONFIG_SPL_BUILD) && \
	!defined(CONFIG_SPL_FSL_LS_PPA)
	#define SPL_NO_IFC
	#endif

	#define CONFIG_REMAKE_ELF
	#define CONFIG_GICV2

	#include <asm/arch/config.h>
	#include <asm/arch/stream_id_lsch2.h>

	/* Link Definitions */
	#ifdef CONFIG_TFABOOT
	#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
	#else
	#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
	#endif

	#define CONFIG_SKIP_LOWLEVEL_INIT

	#define CONFIG_VERY_BIG_RAM
	#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
	#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
	#define CONFIG_SYS_DDR_BLOCK2_BASE 0x880000000ULL

	#define CPU_RELEASE_ADDR secondary_boot_addr

	/* Generic Timer Definitions */
	#define COUNTER_FREQUENCY 25000000 /* 25MHz */

	/* Size of malloc() pool */
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024)

	/* Serial Port */
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK (get_serial_clock())

	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }

	/* SD boot SPL */
	#ifdef CONFIG_SD_BOOT
	#define CONFIG_SPL_MAX_SIZE 0x1f000 /* 124 KiB */
	#define CONFIG_SPL_STACK 0x10020000
	#define CONFIG_SPL_PAD_TO 0x21000 /* 132 KiB */
	#define CONFIG_SPL_BSS_START_ADDR 0x8f000000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
	#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
	CONFIG_SPL_BSS_MAX_SIZE)
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000

	#ifdef CONFIG_NXP_ESBC
	#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
	/*
	* HDR would be appended at end of image and copied to DDR along
	* with U-Boot image. Here u-boot max. size is 512K. So if binary
	* size increases then increase this size in case of secure boot as
	* it uses raw u-boot image instead of fit image.
	*/
	#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
	#else
	#define CONFIG_SYS_MONITOR_LEN 0x100000
	#endif /* ifdef CONFIG_NXP_ESBC */
	#endif

	#if defined(CONFIG_QSPI_BOOT) && defined(CONFIG_SPL)
	#define CONFIG_SPL_TARGET "spl/u-boot-spl.pbl"
	#define CONFIG_SPL_MAX_SIZE 0x1f000
	#define CONFIG_SPL_STACK 0x10020000
	#define CONFIG_SPL_PAD_TO 0x20000
	#define CONFIG_SPL_BSS_START_ADDR 0x8f000000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
	#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
	CONFIG_SPL_BSS_MAX_SIZE)
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
	#define CONFIG_SYS_MONITOR_LEN 0x100000
	#endif

	/* NAND SPL */
	#ifdef CONFIG_NAND_BOOT
	#define CONFIG_SPL_PBL_PAD
	#define CONFIG_SPL_LIBCOMMON_SUPPORT
	#define CONFIG_SPL_LIBGENERIC_SUPPORT
	#define CONFIG_SPL_ENV_SUPPORT
	#define CONFIG_SPL_WATCHDOG_SUPPORT
	#define CONFIG_SPL_I2C_SUPPORT
	#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT

	#define CONFIG_SPL_NAND_SUPPORT
	#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
	#define CONFIG_SPL_MAX_SIZE 0x17000 /* 90 KiB */
	#define CONFIG_SPL_STACK 0x1001f000
	#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE

	#define CONFIG_SPL_BSS_START_ADDR 0x8f000000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
	#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
	CONFIG_SPL_BSS_MAX_SIZE)
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
	#define CONFIG_SYS_MONITOR_LEN 0xa0000
	#endif

	/* GPIO */
	#ifdef CONFIG_DM_GPIO
	#ifndef CONFIG_MPC8XXX_GPIO
	#define CONFIG_MPC8XXX_GPIO
	#endif
	#endif

	/* I2C */
	#if !CONFIG_IS_ENABLED(DM_I2C)
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
	#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
	#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
	#define CONFIG_SYS_I2C_MXC_I2C4 /* enable I2C bus 4 */
	#else
	#define CONFIG_I2C_SET_DEFAULT_BUS_NUM
	#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0
	#endif

	/* PCIe */
	#define CONFIG_PCIE1 /* PCIE controller 1 */
	#define CONFIG_PCIE2 /* PCIE controller 2 */
	#define CONFIG_PCIE3 /* PCIE controller 3 */

	#ifdef CONFIG_PCI
	#define CONFIG_PCI_SCAN_SHOW
	#endif

	/* SATA */
	#ifndef SPL_NO_SATA
	#define CONFIG_SCSI_AHCI_PLAT

	#define CONFIG_SYS_SATA AHCI_BASE_ADDR

	#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
	#define CONFIG_SYS_SCSI_MAX_LUN 1
	#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
	CONFIG_SYS_SCSI_MAX_LUN)
	#endif

	/* FMan ucode */
	#ifndef SPL_NO_FMAN
	#define CONFIG_SYS_DPAA_FMAN
	#ifdef CONFIG_SYS_DPAA_FMAN
	#define CONFIG_SYS_FM_MURAM_SIZE 0x60000
	#endif

	#ifdef CONFIG_TFABOOT
	#define CONFIG_SYS_FMAN_FW_ADDR 0x900000
	#else
	#ifdef CONFIG_SD_BOOT
	/*
	* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
	* about 1MB (2048 blocks), Env is stored after the image, and the env size is
	* 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 18432(0x4800).
	*/
	#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x4800)
	#elif defined(CONFIG_QSPI_BOOT)
	#define CONFIG_SYS_FMAN_FW_ADDR 0x40900000
	#elif defined(CONFIG_NAND_BOOT)
	#define CONFIG_SYS_FMAN_FW_ADDR (36 * CONFIG_SYS_NAND_BLOCK_SIZE)
	#else
	#define CONFIG_SYS_FMAN_FW_ADDR 0x60900000
	#endif
	#endif
	#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
	#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
	#endif

	/* Miscellaneous configurable options */
	#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)

	#define CONFIG_HWCONFIG
	#define HWCONFIG_BUFFER_SIZE 128

	#ifndef CONFIG_SPL_BUILD
	#define BOOT_TARGET_DEVICES(func) \
	func(SCSI, scsi, 0) \
	func(MMC, mmc, 0) \
	func(USB, usb, 0) \
	func(DHCP, dhcp, na)
	#include <config_distro_bootcmd.h>
	#endif

	#if defined(CONFIG_TARGET_LS1046AFRWY)
	#define LS1046A_BOOT_SRC_AND_HDR\
	"boot_scripts=ls1046afrwy_boot.scr\0" \
	"boot_script_hdr=hdr_ls1046afrwy_bs.out\0"
	#elif defined(CONFIG_TARGET_LS1046AQDS)
	#define LS1046A_BOOT_SRC_AND_HDR\
	"boot_scripts=ls1046aqds_boot.scr\0" \
	"boot_script_hdr=hdr_ls1046aqds_bs.out\0"
	#else
	#define LS1046A_BOOT_SRC_AND_HDR\
	"boot_scripts=ls1046ardb_boot.scr\0" \
	"boot_script_hdr=hdr_ls1046ardb_bs.out\0"
	#endif
	#ifndef SPL_NO_MISC
	/* Initial environment variables */
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"hwconfig=fsl_ddr:bank_intlv=auto\0" \
	"ramdisk_addr=0x800000\0" \
	"ramdisk_size=0x2000000\0" \
	"bootm_size=0x10000000\0" \
	"fdt_addr=0x64f00000\0" \
	"kernel_addr=0x61000000\0" \
	"scriptaddr=0x80000000\0" \
	"scripthdraddr=0x80080000\0" \
	"fdtheader_addr_r=0x80100000\0" \
	"kernelheader_addr_r=0x80200000\0" \
	"load_addr=0xa0000000\0" \
	"kernel_addr_r=0x81000000\0" \
	"fdt_addr_r=0x90000000\0" \
	"ramdisk_addr_r=0xa0000000\0" \
	"kernel_start=0x1000000\0" \
	"kernelheader_start=0x600000\0" \
	"kernel_load=0xa0000000\0" \
	"kernel_size=0x2800000\0" \
	"kernelheader_size=0x40000\0" \
	"kernel_addr_sd=0x8000\0" \
	"kernel_size_sd=0x14000\0" \
	"kernelhdr_addr_sd=0x3000\0" \
	"kernelhdr_size_sd=0x10\0" \
	"console=ttyS0,115200\0" \
	CONFIG_MTDPARTS_DEFAULT "\0" \
	BOOTENV \
	LS1046A_BOOT_SRC_AND_HDR \
	"scan_dev_for_boot_part=" \
	"part list ${devtype} ${devnum} devplist; " \
	"env exists devplist \|\| setenv devplist 1; " \
	"for distro_bootpart in ${devplist}; do " \
	"if fstype ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"bootfstype; then " \
	"run scan_dev_for_boot; " \
	"fi; " \
	"done\0" \
	"boot_a_script=" \
	"load ${devtype} ${devnum}:${distro_bootpart} " \
	"${scriptaddr} ${prefix}${script}; " \
	"env exists secureboot && load ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"${scripthdraddr} ${prefix}${boot_script_hdr}; " \
	"env exists secureboot " \
	"&& esbc_validate ${scripthdraddr};" \
	"source ${scriptaddr}\0" \
	"qspi_bootcmd=echo Trying load from qspi..;" \
	"sf probe && sf read $load_addr " \
	"$kernel_start $kernel_size; env exists secureboot " \
	"&& sf read $kernelheader_addr_r $kernelheader_start " \
	"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
	"bootm $load_addr#$board\0" \
	"nand_bootcmd=echo Trying load from nand..;" \
	"nand info; nand read $load_addr " \
	"$kernel_start $kernel_size; env exists secureboot " \
	"&& nand read $kernelheader_addr_r $kernelheader_start " \
	"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
	"bootm $load_addr#$board\0" \
	"nor_bootcmd=echo Trying load from nor..;" \
	"cp.b $kernel_addr $load_addr " \
	"$kernel_size; env exists secureboot " \
	"&& cp.b $kernelheader_addr $kernelheader_addr_r " \
	"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
	"bootm $load_addr#$board\0" \
	"sd_bootcmd=echo Trying load from SD ..;" \
	"mmcinfo; mmc read $load_addr " \
	"$kernel_addr_sd $kernel_size_sd && " \
	"env exists secureboot && mmc read $kernelheader_addr_r " \
	"$kernelhdr_addr_sd $kernelhdr_size_sd " \
	" && esbc_validate ${kernelheader_addr_r};" \
	"bootm $load_addr#$board\0"

	#endif

	/* Monitor Command Prompt */
	#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */

	#define CONFIG_SYS_MAXARGS 64 /* max command args */

	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */

	#include <asm/arch/soc.h>

	#endif /* __LS1046A_COMMON_H */