include/configs/lx2160a_common.h - platform/external/u-boot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2018-2021 NXP
  */

 #ifndef __LX2_COMMON_H
 #define __LX2_COMMON_H

 #include <asm/arch/stream_id_lsch3.h>
 #include <asm/arch/config.h>
 #include <asm/arch/soc.h>

 #define CONFIG_REMAKE_ELF
 #define CONFIG_FSL_LAYERSCAPE
 #define CONFIG_GICV3
 #define CONFIG_FSL_TZPC_BP147
 #define CONFIG_FSL_MEMAC

 #define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_FLASH_BASE		0x20000000

 #define CONFIG_SKIP_LOWLEVEL_INIT

 /* DDR */
 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
 #define CONFIG_SYS_FSL_DDR_INTLV_256B	/* force 256 byte interleaving */
 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_SYS_DDR_SDRAM_BASE		0x80000000UL
 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
 #define CONFIG_SYS_DDR_BLOCK2_BASE		0x2080000000ULL
 #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS	2
 #define CONFIG_SYS_SDRAM_SIZE			0x200000000UL
 #define CONFIG_DDR_SPD
 #define CONFIG_DDR_ECC
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 #define SPD_EEPROM_ADDRESS1		0x51
 #define SPD_EEPROM_ADDRESS2		0x52
 #define SPD_EEPROM_ADDRESS3		0x53
 #define SPD_EEPROM_ADDRESS4		0x54
 #define SPD_EEPROM_ADDRESS5		0x55
 #define SPD_EEPROM_ADDRESS6		0x56
 #define SPD_EEPROM_ADDRESS		SPD_EEPROM_ADDRESS1
 #define CONFIG_SYS_SPD_BUS_NUM		0	/* SPD on I2C bus 0 */
 #define CONFIG_DIMM_SLOTS_PER_CTLR	2
 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
 #define CONFIG_FSL_DDR_BIST	/* enable built-in memory test */
 #define CONFIG_SYS_MONITOR_LEN		(936 * 1024)

 /* Miscellaneous configurable options */
 #define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)

 /* SMP Definitinos  */
 #define CPU_RELEASE_ADDR		secondary_boot_addr

 /* Generic Timer Definitions */
 /*
  * This is not an accurate number. It is used in start.S. The frequency
  * will be udpated later when get_bus_freq(0) is available.
  */

 #define COUNTER_FREQUENCY		25000000	/* 25MHz */

 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2048 * 1024)

 /* Serial Port */
 #define CONFIG_PL01X_SERIAL
 #define CONFIG_PL011_CLOCK		(get_bus_freq(0) / 4)
 #define CONFIG_SYS_SERIAL0		0x21c0000
 #define CONFIG_SYS_SERIAL1		0x21d0000
 #define CONFIG_SYS_SERIAL2		0x21e0000
 #define CONFIG_SYS_SERIAL3		0x21f0000
 /*below might needs to be removed*/
 #define CONFIG_PL01x_PORTS		{(void *)CONFIG_SYS_SERIAL0, \
 					(void *)CONFIG_SYS_SERIAL1, \
 					(void *)CONFIG_SYS_SERIAL2, \
 					(void *)CONFIG_SYS_SERIAL3 }
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

 /* MC firmware */
 #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH		0x20000
 #define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET	0x00F00000
 #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH		0x20000
 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET	0x00F20000
 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS	5000

 /* Define phy_reset function to boot the MC based on mcinitcmd.
  * This happens late enough to properly fixup u-boot env MAC addresses.
  */
 #define CONFIG_RESET_PHY_R

 /*
  * Carve out a DDR region which will not be used by u-boot/Linux
  *
  * It will be used by MC and Debug Server. The MC region must be
  * 512MB aligned, so the min size to hide is 512MB.
  */
 #ifdef CONFIG_FSL_MC_ENET
 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE	(256UL * 1024 * 1024)
 #endif

 /* I2C bus multiplexer */
 #define I2C_MUX_PCA_ADDR_PRI		0x77 /* Primary Mux*/
 #define I2C_MUX_CH_DEFAULT		0x8

 /* RTC */
 #define RTC
 #define CONFIG_SYS_I2C_RTC_ADDR		0x51  /* Channel 3*/

 /* EEPROM */
 #define CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM		0
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5

 /* Qixis */
 #define CONFIG_FSL_QIXIS
 #define CONFIG_QIXIS_I2C_ACCESS
 #define CONFIG_SYS_I2C_FPGA_ADDR		0x66

 /* PCI */
 #ifdef CONFIG_PCI
 #define CONFIG_SYS_PCI_64BIT
 #define CONFIG_PCI_SCAN_SHOW
 #endif

 /* SATA */

 #ifdef CONFIG_SCSI
 #define CONFIG_SCSI_AHCI_PLAT
 #define CONFIG_SYS_SATA1		AHCI_BASE_ADDR1
 #define CONFIG_SYS_SATA2		AHCI_BASE_ADDR2
 #define CONFIG_SYS_SCSI_MAX_SCSI_ID	1
 #define CONFIG_SYS_SCSI_MAX_LUN		1
 #define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 					CONFIG_SYS_SCSI_MAX_LUN)
 #endif

 /* USB */
 #ifdef CONFIG_USB_HOST
 #define CONFIG_HAS_FSL_XHCI_USB
 #ifndef CONFIG_TARGET_LX2162AQDS
 #define CONFIG_USB_MAX_CONTROLLER_COUNT	2
 #endif
 #endif

 /* GPIO */
 #ifdef CONFIG_DM_GPIO
 #ifndef CONFIG_MPC8XXX_GPIO
 #define CONFIG_MPC8XXX_GPIO
 #endif
 #endif

 #ifndef __ASSEMBLY__
 unsigned long get_board_sys_clk(void);
 unsigned long get_board_ddr_clk(void);
 #endif

 #define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
 #define CONFIG_DDR_CLK_FREQ		get_board_ddr_clk()
 #define COUNTER_FREQUENCY_REAL		(CONFIG_SYS_CLK_FREQ / 4)

 #define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE		128

 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE /* Boot args buffer */
 #define CONFIG_SYS_MAXARGS		64	/* max command args */

 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */

 /* Initial environment variables */
 #define XSPI_MC_INIT_CMD				\
 	"sf probe 0:0 && "				\
 	"sf read 0x80640000 0x640000 0x80000 && "	\
 	"env exists secureboot && "			\
 	"esbc_validate 0x80640000 && "			\
 	"esbc_validate 0x80680000; "			\
 	"sf read 0x80a00000 0xa00000 0x300000 && "	\
 	"sf read 0x80e00000 0xe00000 0x100000; "	\
 	"fsl_mc start mc 0x80a00000 0x80e00000\0"

 #define SD_MC_INIT_CMD				\
 	"mmc read 0x80a00000 0x5000 0x1200;"	\
 	"mmc read 0x80e00000 0x7000 0x800;"	\
 	"env exists secureboot && "		\
 	"mmc read 0x80640000 0x3200 0x20 && "	\
 	"mmc read 0x80680000 0x3400 0x20 && "	\
 	"esbc_validate 0x80640000 && "		\
 	"esbc_validate 0x80680000 ;"		\
 	"fsl_mc start mc 0x80a00000 0x80e00000\0"

 #define SD2_MC_INIT_CMD				\
 	"mmc dev 1; mmc read 0x80a00000 0x5000 0x1200;"	\
 	"mmc read 0x80e00000 0x7000 0x800;"	\
 	"env exists secureboot && "		\
 	"mmc read 0x80640000 0x3200 0x20 && "	\
 	"mmc read 0x80680000 0x3400 0x20 && "	\
 	"esbc_validate 0x80640000 && "		\
 	"esbc_validate 0x80680000 ;"		\
 	"fsl_mc start mc 0x80a00000 0x80e00000\0"

 #define EXTRA_ENV_SETTINGS			\
 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
 	"ramdisk_addr=0x800000\0"		\
 	"ramdisk_size=0x2000000\0"		\
 	"fdt_high=0xa0000000\0"			\
 	"initrd_high=0xffffffffffffffff\0"	\
 	"fdt_addr=0x64f00000\0"			\
 	"kernel_start=0x1000000\0"		\
 	"kernelheader_start=0x600000\0"		\
 	"scriptaddr=0x80000000\0"		\
 	"scripthdraddr=0x80080000\0"		\
 	"fdtheader_addr_r=0x80100000\0"		\
 	"kernelheader_addr_r=0x80200000\0"	\
 	"kernel_addr_r=0x81000000\0"		\
 	"kernelheader_size=0x40000\0"		\
 	"fdt_addr_r=0x90000000\0"		\
 	"load_addr=0xa0000000\0"		\
 	"kernel_size=0x2800000\0"		\
 	"kernel_addr_sd=0x8000\0"		\
 	"kernelhdr_addr_sd=0x3000\0"            \
 	"kernel_size_sd=0x14000\0"              \
 	"kernelhdr_size_sd=0x20\0"              \
 	"console=ttyAMA0,38400n8\0"		\
 	BOOTENV					\
 	"mcmemsize=0x70000000\0"		\
 	XSPI_MC_INIT_CMD				\
 	"scan_dev_for_boot_part="		\
 		"part list ${devtype} ${devnum} devplist; "	\
 		"env exists devplist || setenv devplist 1; "	\
 		"for distro_bootpart in ${devplist}; do "	\
 			"if fstype ${devtype} "			\
 				"${devnum}:${distro_bootpart} "	\
 				"bootfstype; then "		\
 				"run scan_dev_for_boot; "	\
 			"fi; "					\
 		"done\0"					\
 	"boot_a_script="					\
 		"load ${devtype} ${devnum}:${distro_bootpart} "	\
 			"${scriptaddr} ${prefix}${script}; "	\
 		"env exists secureboot && load ${devtype} "	\
 			"${devnum}:${distro_bootpart} "		\
 			"${scripthdraddr} ${prefix}${boot_script_hdr} "	\
 			"&& esbc_validate ${scripthdraddr};"	\
 		"source ${scriptaddr}\0"

 #define XSPI_NOR_BOOTCOMMAND						\
 			"sf probe 0:0; "				\
 			"sf read 0x806c0000 0x6c0000 0x40000; "		\
 			"env exists mcinitcmd && env exists secureboot"	\
 			" && esbc_validate 0x806c0000; "		\
 			"sf read 0x80d00000 0xd00000 0x100000; "	\
 			"env exists mcinitcmd && "			\
 			"fsl_mc lazyapply dpl 0x80d00000; "		\
 			"run distro_bootcmd;run xspi_bootcmd; "		\
 			"env exists secureboot && esbc_halt;"

 #define SD_BOOTCOMMAND						\
 		"env exists mcinitcmd && mmcinfo; "		\
 		"mmc read 0x80d00000 0x6800 0x800; "		\
 		"env exists mcinitcmd && env exists secureboot "	\
 		" && mmc read 0x806C0000 0x3600 0x20 "		\
 		"&& esbc_validate 0x806C0000;env exists mcinitcmd "	\
 		"&& fsl_mc lazyapply dpl 0x80d00000;"		\
 		"run distro_bootcmd;run sd_bootcmd;"		\
 		"env exists secureboot && esbc_halt;"

 #define SD2_BOOTCOMMAND						\
 		"mmc dev 1; env exists mcinitcmd && mmcinfo; "	\
 		"mmc read 0x80d00000 0x6800 0x800; "		\
 		"env exists mcinitcmd && env exists secureboot "	\
 		" && mmc read 0x806C0000 0x3600 0x20 "		\
 		"&& esbc_validate 0x806C0000;env exists mcinitcmd "	\
 		"&& fsl_mc lazyapply dpl 0x80d00000;"		\
 		"run distro_bootcmd;run sd2_bootcmd;"		\
 		"env exists secureboot && esbc_halt;"

 #define BOOT_TARGET_DEVICES(func) \
 	func(USB, usb, 0) \
 	func(MMC, mmc, 0) \
 	func(MMC, mmc, 1) \
 	func(SCSI, scsi, 0) \
 	func(DHCP, dhcp, na)
 #include <config_distro_bootcmd.h>

 #endif /* __LX2_COMMON_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright 2018-2021 NXP
	*/

	#ifndef __LX2_COMMON_H
	#define __LX2_COMMON_H

	#include <asm/arch/stream_id_lsch3.h>
	#include <asm/arch/config.h>
	#include <asm/arch/soc.h>

	#define CONFIG_REMAKE_ELF
	#define CONFIG_FSL_LAYERSCAPE
	#define CONFIG_GICV3
	#define CONFIG_FSL_TZPC_BP147
	#define CONFIG_FSL_MEMAC

	#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_FLASH_BASE 0x20000000

	#define CONFIG_SKIP_LOWLEVEL_INIT

	/* DDR */
	#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
	#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */
	#define CONFIG_VERY_BIG_RAM
	#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
	#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
	#define CONFIG_SYS_DDR_BLOCK2_BASE 0x2080000000ULL
	#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2
	#define CONFIG_SYS_SDRAM_SIZE 0x200000000UL
	#define CONFIG_DDR_SPD
	#define CONFIG_DDR_ECC
	#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
	#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
	#define SPD_EEPROM_ADDRESS1 0x51
	#define SPD_EEPROM_ADDRESS2 0x52
	#define SPD_EEPROM_ADDRESS3 0x53
	#define SPD_EEPROM_ADDRESS4 0x54
	#define SPD_EEPROM_ADDRESS5 0x55
	#define SPD_EEPROM_ADDRESS6 0x56
	#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
	#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */
	#define CONFIG_DIMM_SLOTS_PER_CTLR 2
	#define CONFIG_CHIP_SELECTS_PER_CTRL 4
	#define CONFIG_FSL_DDR_BIST /* enable built-in memory test */
	#define CONFIG_SYS_MONITOR_LEN (936 * 1024)

	/* Miscellaneous configurable options */
	#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)

	/* SMP Definitinos */
	#define CPU_RELEASE_ADDR secondary_boot_addr

	/* Generic Timer Definitions */
	/*
	* This is not an accurate number. It is used in start.S. The frequency
	* will be udpated later when get_bus_freq(0) is available.
	*/

	#define COUNTER_FREQUENCY 25000000 /* 25MHz */

	/* Size of malloc() pool */
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024)

	/* Serial Port */
	#define CONFIG_PL01X_SERIAL
	#define CONFIG_PL011_CLOCK (get_bus_freq(0) / 4)
	#define CONFIG_SYS_SERIAL0 0x21c0000
	#define CONFIG_SYS_SERIAL1 0x21d0000
	#define CONFIG_SYS_SERIAL2 0x21e0000
	#define CONFIG_SYS_SERIAL3 0x21f0000
	/below might needs to be removed/
	#define CONFIG_PL01x_PORTS {(void *)CONFIG_SYS_SERIAL0, \
	(void *)CONFIG_SYS_SERIAL1, \
	(void *)CONFIG_SYS_SERIAL2, \
	(void *)CONFIG_SYS_SERIAL3 }
	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }

	/* MC firmware */
	#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
	#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
	#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
	#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
	#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000

	/* Define phy_reset function to boot the MC based on mcinitcmd.
	* This happens late enough to properly fixup u-boot env MAC addresses.
	*/
	#define CONFIG_RESET_PHY_R

	/*
	* Carve out a DDR region which will not be used by u-boot/Linux
	*
	* It will be used by MC and Debug Server. The MC region must be
	* 512MB aligned, so the min size to hide is 512MB.
	*/
	#ifdef CONFIG_FSL_MC_ENET
	#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (256UL * 1024 * 1024)
	#endif

	/* I2C bus multiplexer */
	#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/
	#define I2C_MUX_CH_DEFAULT 0x8

	/* RTC */
	#define RTC
	#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/

	/* EEPROM */
	#define CONFIG_ID_EEPROM
	#define CONFIG_SYS_I2C_EEPROM_NXID
	#define CONFIG_SYS_EEPROM_BUS_NUM 0
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5

	/* Qixis */
	#define CONFIG_FSL_QIXIS
	#define CONFIG_QIXIS_I2C_ACCESS
	#define CONFIG_SYS_I2C_FPGA_ADDR 0x66

	/* PCI */
	#ifdef CONFIG_PCI
	#define CONFIG_SYS_PCI_64BIT
	#define CONFIG_PCI_SCAN_SHOW
	#endif

	/* SATA */

	#ifdef CONFIG_SCSI
	#define CONFIG_SCSI_AHCI_PLAT
	#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
	#define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2
	#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
	#define CONFIG_SYS_SCSI_MAX_LUN 1
	#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
	CONFIG_SYS_SCSI_MAX_LUN)
	#endif

	/* USB */
	#ifdef CONFIG_USB_HOST
	#define CONFIG_HAS_FSL_XHCI_USB
	#ifndef CONFIG_TARGET_LX2162AQDS
	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
	#endif
	#endif

	/* GPIO */
	#ifdef CONFIG_DM_GPIO
	#ifndef CONFIG_MPC8XXX_GPIO
	#define CONFIG_MPC8XXX_GPIO
	#endif
	#endif

	#ifndef __ASSEMBLY__
	unsigned long get_board_sys_clk(void);
	unsigned long get_board_ddr_clk(void);
	#endif

	#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
	#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
	#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ / 4)

	#define CONFIG_HWCONFIG
	#define HWCONFIG_BUFFER_SIZE 128

	/* Monitor Command Prompt */
	#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
	sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
	#define CONFIG_SYS_MAXARGS 64 /* max command args */

	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */

	/* Initial environment variables */
	#define XSPI_MC_INIT_CMD \
	"sf probe 0:0 && " \
	"sf read 0x80640000 0x640000 0x80000 && " \
	"env exists secureboot && " \
	"esbc_validate 0x80640000 && " \
	"esbc_validate 0x80680000; " \
	"sf read 0x80a00000 0xa00000 0x300000 && " \
	"sf read 0x80e00000 0xe00000 0x100000; " \
	"fsl_mc start mc 0x80a00000 0x80e00000\0"

	#define SD_MC_INIT_CMD \
	"mmc read 0x80a00000 0x5000 0x1200;" \
	"mmc read 0x80e00000 0x7000 0x800;" \
	"env exists secureboot && " \
	"mmc read 0x80640000 0x3200 0x20 && " \
	"mmc read 0x80680000 0x3400 0x20 && " \
	"esbc_validate 0x80640000 && " \
	"esbc_validate 0x80680000 ;" \
	"fsl_mc start mc 0x80a00000 0x80e00000\0"

	#define SD2_MC_INIT_CMD \
	"mmc dev 1; mmc read 0x80a00000 0x5000 0x1200;" \
	"mmc read 0x80e00000 0x7000 0x800;" \
	"env exists secureboot && " \
	"mmc read 0x80640000 0x3200 0x20 && " \
	"mmc read 0x80680000 0x3400 0x20 && " \
	"esbc_validate 0x80640000 && " \
	"esbc_validate 0x80680000 ;" \
	"fsl_mc start mc 0x80a00000 0x80e00000\0"

	#define EXTRA_ENV_SETTINGS \
	"hwconfig=fsl_ddr:bank_intlv=auto\0" \
	"ramdisk_addr=0x800000\0" \
	"ramdisk_size=0x2000000\0" \
	"fdt_high=0xa0000000\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"fdt_addr=0x64f00000\0" \
	"kernel_start=0x1000000\0" \
	"kernelheader_start=0x600000\0" \
	"scriptaddr=0x80000000\0" \
	"scripthdraddr=0x80080000\0" \
	"fdtheader_addr_r=0x80100000\0" \
	"kernelheader_addr_r=0x80200000\0" \
	"kernel_addr_r=0x81000000\0" \
	"kernelheader_size=0x40000\0" \
	"fdt_addr_r=0x90000000\0" \
	"load_addr=0xa0000000\0" \
	"kernel_size=0x2800000\0" \
	"kernel_addr_sd=0x8000\0" \
	"kernelhdr_addr_sd=0x3000\0" \
	"kernel_size_sd=0x14000\0" \
	"kernelhdr_size_sd=0x20\0" \
	"console=ttyAMA0,38400n8\0" \
	BOOTENV \
	"mcmemsize=0x70000000\0" \
	XSPI_MC_INIT_CMD \
	"scan_dev_for_boot_part=" \
	"part list ${devtype} ${devnum} devplist; " \
	"env exists devplist \|\| setenv devplist 1; " \
	"for distro_bootpart in ${devplist}; do " \
	"if fstype ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"bootfstype; then " \
	"run scan_dev_for_boot; " \
	"fi; " \
	"done\0" \
	"boot_a_script=" \
	"load ${devtype} ${devnum}:${distro_bootpart} " \
	"${scriptaddr} ${prefix}${script}; " \
	"env exists secureboot && load ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"${scripthdraddr} ${prefix}${boot_script_hdr} " \
	"&& esbc_validate ${scripthdraddr};" \
	"source ${scriptaddr}\0"

	#define XSPI_NOR_BOOTCOMMAND \
	"sf probe 0:0; " \
	"sf read 0x806c0000 0x6c0000 0x40000; " \
	"env exists mcinitcmd && env exists secureboot" \
	" && esbc_validate 0x806c0000; " \
	"sf read 0x80d00000 0xd00000 0x100000; " \
	"env exists mcinitcmd && " \
	"fsl_mc lazyapply dpl 0x80d00000; " \
	"run distro_bootcmd;run xspi_bootcmd; " \
	"env exists secureboot && esbc_halt;"

	#define SD_BOOTCOMMAND \
	"env exists mcinitcmd && mmcinfo; " \
	"mmc read 0x80d00000 0x6800 0x800; " \
	"env exists mcinitcmd && env exists secureboot " \
	" && mmc read 0x806C0000 0x3600 0x20 " \
	"&& esbc_validate 0x806C0000;env exists mcinitcmd " \
	"&& fsl_mc lazyapply dpl 0x80d00000;" \
	"run distro_bootcmd;run sd_bootcmd;" \
	"env exists secureboot && esbc_halt;"

	#define SD2_BOOTCOMMAND \
	"mmc dev 1; env exists mcinitcmd && mmcinfo; " \
	"mmc read 0x80d00000 0x6800 0x800; " \
	"env exists mcinitcmd && env exists secureboot " \
	" && mmc read 0x806C0000 0x3600 0x20 " \
	"&& esbc_validate 0x806C0000;env exists mcinitcmd " \
	"&& fsl_mc lazyapply dpl 0x80d00000;" \
	"run distro_bootcmd;run sd2_bootcmd;" \
	"env exists secureboot && esbc_halt;"

	#define BOOT_TARGET_DEVICES(func) \
	func(USB, usb, 0) \
	func(MMC, mmc, 0) \
	func(MMC, mmc, 1) \
	func(SCSI, scsi, 0) \
	func(DHCP, dhcp, na)
	#include <config_distro_bootcmd.h>

	#endif /* __LX2_COMMON_H */