blob: d2d20269ba07ea1df40071dc9ab010c2482f67d3 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2019 NXP
* Copyright 2020 Linaro
*/
#include <common.h>
#include <command.h>
#include <cpu_func.h>
#include <hang.h>
#include <image.h>
#include <init.h>
#include <log.h>
#include <spl.h>
#include <asm/io.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx8mm_pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <asm/mach-imx/gpio.h>
#include <asm/arch/ddr.h>
#include <dm/uclass.h>
#include <dm/device.h>
#include <dm/uclass-internal.h>
#include <dm/device-internal.h>
#include <power/pmic.h>
#include <power/bd71837.h>
#include "ddr/ddr.h"
DECLARE_GLOBAL_DATA_PTR;
int spl_board_boot_device(enum boot_device boot_dev_spl)
{
switch (boot_dev_spl) {
case SD2_BOOT:
case MMC2_BOOT:
return BOOT_DEVICE_MMC1;
case SD3_BOOT:
case MMC3_BOOT:
return BOOT_DEVICE_MMC2;
default:
return BOOT_DEVICE_NONE;
}
}
#define I2C_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PE)
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
struct i2c_pads_info i2c_pad_info1 = {
.scl = {
.i2c_mode = IMX8MM_PAD_I2C2_SCL_I2C2_SCL | PC,
.gpio_mode = IMX8MM_PAD_I2C2_SCL_GPIO5_IO16 | PC,
.gp = IMX_GPIO_NR(5, 16),
},
.sda = {
.i2c_mode = IMX8MM_PAD_I2C2_SDA_I2C2_SDA | PC,
.gpio_mode = IMX8MM_PAD_I2C2_SDA_GPIO5_IO17 | PC,
.gp = IMX_GPIO_NR(5, 17),
},
};
static void spl_dram_init(void)
{
spl_dram_init_compulab();
}
void spl_board_init(void)
{
puts("Normal Boot\n");
}
#ifdef CONFIG_SPL_LOAD_FIT
int board_fit_config_name_match(const char *name)
{
/* Just empty function now - can't decide what to choose */
debug("%s: %s\n", __func__, name);
return 0;
}
#endif
static int power_init_board(void)
{
struct udevice *dev;
int ret;
ret = pmic_get("pmic@4b", &dev);
if (ret == -ENODEV) {
puts("No pmic\n");
return 0;
}
if (ret != 0)
return ret;
/* decrease RESET key long push time from the default 10s to 10ms */
pmic_reg_write(dev, BD718XX_PWRONCONFIG1, 0x0);
/* unlock the PMIC regs */
pmic_reg_write(dev, BD718XX_REGLOCK, 0x1);
/* increase VDD_SOC to typical value 0.85v before first DRAM access */
pmic_reg_write(dev, BD718XX_BUCK1_VOLT_RUN, 0x0f);
/* increase VDD_DRAM to 0.975v for 3Ghz DDR */
pmic_reg_write(dev, BD718XX_1ST_NODVS_BUCK_VOLT, 0x83);
/* increase NVCC_DRAM_1V2 to 1.2v for DDR4 */
pmic_reg_write(dev, BD718XX_4TH_NODVS_BUCK_VOLT, 0x28);
/* lock the PMIC regs */
pmic_reg_write(dev, BD718XX_REGLOCK, 0x11);
return 0;
}
void board_init_f(ulong dummy)
{
struct udevice *dev;
int ret;
arch_cpu_init();
init_uart_clk(2);
timer_init();
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
ret = spl_early_init();
if (ret) {
debug("spl_early_init() failed: %d\n", ret);
hang();
}
preloader_console_init();
ret = uclass_get_device_by_name(UCLASS_CLK,
"clock-controller@30380000",
&dev);
if (ret < 0) {
printf("Failed to find clock node. Check device tree\n");
hang();
}
enable_tzc380();
setup_i2c(1, 100000, 0x7f, &i2c_pad_info1);
power_init_board();
/* DDR initialization */
spl_dram_init();
board_init_r(NULL, 0);
}