| /* |
| * (C) Copyright 2004, Psyent Corporation <www.psyent.com> |
| * Scott McNutt <smcnutt@psyent.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /*------------------------------------------------------------------------ |
| * BOARD/CPU |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_PK1C20 1 /* PK1C20 board */ |
| #define CONFIG_SYS_CLK_FREQ 50000000 /* 50 MHz core clk */ |
| |
| #define CONFIG_SYS_RESET_ADDR 0x00000000 /* Hard-reset address */ |
| #define CONFIG_SYS_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/ |
| #define CONFIG_SYS_NIOS_SYSID_BASE 0x021208b8 /* System id address */ |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/ |
| |
| /*------------------------------------------------------------------------ |
| * CACHE -- the following will support II/s and II/f. The II/s does not |
| * have dcache, so the cache instructions will behave as NOPs. |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_ICACHE_SIZE 4096 /* 4 KByte total */ |
| #define CONFIG_SYS_ICACHELINE_SIZE 32 /* 32 bytes/line */ |
| #define CONFIG_SYS_DCACHE_SIZE 2048 /* 2 KByte (II/f) */ |
| #define CONFIG_SYS_DCACHELINE_SIZE 4 /* 4 bytes/line (II/f) */ |
| |
| /*------------------------------------------------------------------------ |
| * MEMORY BASE ADDRESSES |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_FLASH_BASE 0x00000000 /* FLASH base addr */ |
| #define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */ |
| #define CONFIG_SYS_SDRAM_BASE 0x01000000 /* SDRAM base addr */ |
| #define CONFIG_SYS_SDRAM_SIZE 0x01000000 /* 16 MByte */ |
| #define CONFIG_SYS_SRAM_BASE 0x02000000 /* SRAM base addr */ |
| #define CONFIG_SYS_SRAM_SIZE 0x00100000 /* 1 MB (only 1M mapped)*/ |
| |
| /*------------------------------------------------------------------------ |
| * MEMORY ORGANIZATION |
| * -Monitor at top. |
| * -The heap is placed below the monitor. |
| * -Global data is placed below the heap. |
| * -The stack is placed below global data (&grows down). |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 128k */ |
| #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) |
| |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_MALLOC_BASE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /*------------------------------------------------------------------------ |
| * FLASH (AM29LV065D) |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_MAX_FLASH_SECT 128 /* Max # sects per bank */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max # of flash banks */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */ |
| #define CONFIG_SYS_FLASH_WORD_SIZE unsigned char /* flash word size */ |
| |
| /*------------------------------------------------------------------------ |
| * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above |
| * CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the |
| * reset address, no? This will keep the environment in user region |
| * of flash. NOTE: the monitor length must be multiple of sector size |
| * (which is common practice). |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_ENV_IS_IN_FLASH 1 /* Environment in flash */ |
| #define CONFIG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */ |
| #define CONFIG_ENV_OVERWRITE /* Serial change Ok */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_RESET_ADDR + CONFIG_SYS_MONITOR_LEN) |
| |
| /*------------------------------------------------------------------------ |
| * CONSOLE |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_ALTERA_UART 1 /* Use altera uart */ |
| #if defined(CONFIG_ALTERA_JTAG_UART) |
| #define CONFIG_SYS_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */ |
| #else |
| #define CONFIG_SYS_NIOS_CONSOLE 0x02120840 /* UART base addr */ |
| #endif |
| |
| #define CONFIG_SYS_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */ |
| #define CONFIG_BAUDRATE 115200 /* Initial baudrate */ |
| #define CONFIG_SYS_BAUDRATE_TABLE {115200} /* It's fixed ;-) */ |
| |
| #define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* Suppress console info*/ |
| |
| /*------------------------------------------------------------------------ |
| * EPCS Device -- wne CONFIG_SYS_NIOS_EPCSBASE is defined code/commands for |
| * epcs device access is enabled. The base address is the epcs |
| * _register_ base address, NOT THE ADDRESS OF THE MEMORY BLOCK. |
| * The register base is currently at offset 0x600 from the memory base. |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_NIOS_EPCSBASE 0x02100200 /* EPCS register base */ |
| |
| /*------------------------------------------------------------------------ |
| * DEBUG |
| *----------------------------------------------------------------------*/ |
| #undef CONFIG_ROM_STUBS /* Stubs not in ROM */ |
| |
| /*------------------------------------------------------------------------ |
| * TIMEBASE -- |
| * |
| * The high res timer defaults to 1 msec. Since it includes the period |
| * registers, the interrupt frequency can be reduced using TMRCNT. |
| * If the default period is acceptable, TMRCNT can be left undefined. |
| * TMRMS represents the desired mecs per tick (msecs per interrupt). |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_HZ 1000 /* Always 1000 */ |
| #define CONFIG_SYS_LOW_RES_TIMER |
| #define CONFIG_SYS_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */ |
| #define CONFIG_SYS_NIOS_TMRIRQ 3 /* Timer IRQ num */ |
| #define CONFIG_SYS_NIOS_TMRMS 10 /* Desired period */ |
| #define CONFIG_SYS_NIOS_TMRCNT \ |
| (CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000)) |
| |
| /*------------------------------------------------------------------------ |
| * STATUS LED -- Provides a simple blinking led. For Nios2 each board |
| * must implement its own led routines -- leds are, after all, |
| * board-specific, no? |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */ |
| #define CONFIG_STATUS_LED /* Enable status driver */ |
| #define CONFIG_BOARD_SPECIFIC_LED |
| |
| #define STATUS_LED_BIT 1 /* Bit-0 on PIO */ |
| #define STATUS_LED_STATE 1 /* Blinking */ |
| #define STATUS_LED_PERIOD (500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec */ |
| |
| /*------------------------------------------------------------------------ |
| * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ... |
| * and really doesn't need any additional clutter. So I choose the lazy |
| * way out to avoid changes there -- define the base address to ensure |
| * cache bypass so there's no need to monkey with inx/outx macros. |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */ |
| #define CONFIG_SMC91111 /* Using SMC91c111 */ |
| #undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */ |
| #define CONFIG_SMC_USE_32_BIT /* 32-bit interface */ |
| |
| #define CONFIG_ETHADDR 08:00:3e:26:0a:5b |
| #define CONFIG_NETMASK 255.255.255.0 |
| #define CONFIG_IPADDR 192.168.2.21 |
| #define CONFIG_SERVERIP 192.168.2.16 |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| |
| #define CONFIG_CMD_BDI |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_ECHO |
| #define CONFIG_CMD_SAVEENV |
| #define CONFIG_CMD_FLASH |
| #define CONFIG_CMD_IMI |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_LOADS |
| #define CONFIG_CMD_LOADB |
| #define CONFIG_CMD_MEMORY |
| #define CONFIG_CMD_MISC |
| #define CONFIG_CMD_NET |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_RUN |
| #define CONFIG_CMD_SAVES |
| |
| |
| /*------------------------------------------------------------------------ |
| * COMPACT FLASH |
| *----------------------------------------------------------------------*/ |
| #if defined(CONFIG_CMD_IDE) |
| #define CONFIG_IDE_PREINIT /* Implement id_preinit */ |
| #define CONFIG_SYS_IDE_MAXBUS 1 /* 1 IDE bus */ |
| #define CONFIG_SYS_IDE_MAXDEVICE 1 /* 1 drive per IDE bus */ |
| |
| #define CONFIG_SYS_ATA_BASE_ADDR 0x00900800 /* ATA base addr */ |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 /* IDE0 offset */ |
| #define CONFIG_SYS_ATA_DATA_OFFSET 0x0040 /* Data IO offset */ |
| #define CONFIG_SYS_ATA_REG_OFFSET 0x0040 /* Register offset */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 /* Alternate reg offset */ |
| #define CONFIG_SYS_ATA_STRIDE 4 /* Width betwix addrs */ |
| #define CONFIG_DOS_PARTITION |
| |
| /* Board-specific cf regs */ |
| #define CONFIG_SYS_CF_PRESENT 0x00900880 /* CF Present PIO base */ |
| #define CONFIG_SYS_CF_POWER 0x00900890 /* CF Power FET PIO base*/ |
| #define CONFIG_SYS_CF_ATASEL 0x009008a0 /* CF ATASEL PIO base */ |
| |
| #endif |
| |
| /*------------------------------------------------------------------------ |
| * JFFS2 |
| *----------------------------------------------------------------------*/ |
| #if defined(CONFIG_CMD_JFFS2) |
| #define CONFIG_SYS_JFFS_CUSTOM_PART /* board defined part */ |
| #endif |
| |
| /*------------------------------------------------------------------------ |
| * MISC |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_LONGHELP /* Provide extended help*/ |
| #define CONFIG_SYS_PROMPT "==> " /* Command prompt */ |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */ |
| #define CONFIG_SYS_MAXARGS 16 /* Max command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg buf size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */ |
| #define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE /* Default load address */ |
| #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE /* Start addr for test */ |
| #define CONFIG_SYS_MEMTEST_END CONFIG_SYS_INIT_SP - 0x00020000 |
| |
| #define CONFIG_SYS_HUSH_PARSER |
| |
| #endif /* __CONFIG_H */ |