include/configs/ls1028a_common.h

/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright 2019 NXP
 */

#ifndef __L1028A_COMMON_H
#define __L1028A_COMMON_H

#define CONFIG_REMAKE_ELF
#define CONFIG_FSL_LAYERSCAPE
#define CONFIG_MP

#include <asm/arch/stream_id_lsch3.h>
#include <asm/arch/config.h>
#include <asm/arch/soc.h>

/* Link Definitions */
#define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_TEXT_BASE

#define CONFIG_SKIP_LOWLEVEL_INIT

#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000UL
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_DDR_BLOCK2_BASE	0x2080000000ULL
#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS	1

#define CONFIG_CMD_MEMTEST
#define CONFIG_SYS_MEMTEST_START        0x80000000
#define CONFIG_SYS_MEMTEST_END          0x9fffffff

/*
 * SMP Definitinos
 */
#define CPU_RELEASE_ADDR		secondary_boot_func

/* Generic Timer Definitions */
#define COUNTER_FREQUENCY		25000000	/* 25MHz */

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2048 * 1024)

/* I2C */
#ifndef CONFIG_DM_I2C
#define CONFIG_SYS_I2C
#endif

/* Serial Port */
#define CONFIG_CONS_INDEX       1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0) / 2)

#define CONFIG_BAUDRATE			115200
#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)

/* Physical Memory Map */
#define CONFIG_CHIP_SELECTS_PER_CTRL	4

#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE		128

/* Allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE

#define BOOT_TARGET_DEVICES(func) \
	func(MMC, mmc, 0) \
	func(MMC, mmc, 1) \
	func(USB, usb, 0)
#include <config_distro_bootcmd.h>

/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS		\
	"board=ls1028ardb\0"			\
	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
	"ramdisk_addr=0x800000\0"		\
	"ramdisk_size=0x2000000\0"		\
	"fdt_high=0xffffffffffffffff\0"		\
	"initrd_high=0xffffffffffffffff\0"	\
	"fdt_addr=0x00f00000\0"                 \
	"kernel_addr=0x01000000\0"              \
	"scriptaddr=0x80000000\0"               \
	"scripthdraddr=0x80080000\0"		\
	"fdtheader_addr_r=0x80100000\0"         \
	"kernelheader_addr_r=0x80200000\0"      \
	"load_addr=0xa0000000\0"            \
	"kernel_addr_r=0x81000000\0"            \
	"fdt_addr_r=0x90000000\0"               \
	"ramdisk_addr_r=0xa0000000\0"           \
	"kernel_start=0x1000000\0"		\
	"kernelheader_start=0x800000\0"		\
	"kernel_load=0xa0000000\0"		\
	"kernel_size=0x2800000\0"		\
	"kernelheader_size=0x40000\0"		\
	"kernel_addr_sd=0x8000\0"		\
	"kernel_size_sd=0x14000\0"		\
	"kernelhdr_addr_sd=0x4000\0"		\
	"kernelhdr_size_sd=0x10\0"		\
	"console=ttyS0,115200\0"                \
	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"	\
	BOOTENV					\
	"boot_scripts=ls1028ardb_boot.scr\0"    \
	"boot_script_hdr=hdr_ls1028ardb_bs.out\0"	\
	"scan_dev_for_boot_part="               \
		"part list ${devtype} ${devnum} devplist; "   \
		"env exists devplist || setenv devplist 1; "  \
		"for distro_bootpart in ${devplist}; do "     \
		  "if fstype ${devtype} "                  \
			"${devnum}:${distro_bootpart} "      \
			"bootfstype; then "                  \
			"run scan_dev_for_boot; "            \
		  "fi; "                                   \
		"done\0"                                   \
	"scan_dev_for_boot="				  \
		"echo Scanning ${devtype} "		  \
				"${devnum}:${distro_bootpart}...; "  \
		"for prefix in ${boot_prefixes}; do "	  \
			"run scan_dev_for_scripts; "	  \
		"done;"					  \
		"\0"					  \
	"boot_a_script="				  \
		"load ${devtype} ${devnum}:${distro_bootpart} "  \
			"${scriptaddr} ${prefix}${script}; "    \
		"env exists secureboot && load ${devtype} "     \
			"${devnum}:${distro_bootpart} "		\
			"${scripthdraddr} ${prefix}${boot_script_hdr} " \
			"&& esbc_validate ${scripthdraddr};"    \
		"source ${scriptaddr}\0"	  \
	"xspi_bootcmd=echo Trying load from FlexSPI flash ...;" \
		"sf probe 0:0 && sf read $load_addr " \
		"$kernel_start $kernel_size ; env exists secureboot &&" \
		"sf read $kernelheader_addr_r $kernelheader_start " \
		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
		" bootm $load_addr#$board\0" \
	"xspi_hdploadcmd=echo Trying load HDP firmware from FlexSPI...;" \
		"sf probe 0:0 && sf read $load_addr 0x940000 0x30000 " \
		"&& hdp load $load_addr 0x2000\0"			\
	"sd_bootcmd=echo Trying load from SD ...;" \
		"mmcinfo; mmc read $load_addr "		\
		"$kernel_addr_sd $kernel_size_sd && "	\
		"env exists secureboot && mmc read $kernelheader_addr_r " \
		"$kernelhdr_addr_sd $kernelhdr_size_sd "		\
		" && esbc_validate ${kernelheader_addr_r};"	\
		"bootm $load_addr#$board\0"		\
	"sd_hdploadcmd=echo Trying load HDP firmware from SD..;"        \
		"mmcinfo;mmc read $load_addr 0x4a00 0x200 "             \
		"&& hdp load $load_addr 0x2000\0"	\
	"emmc_bootcmd=echo Trying load from EMMC ..;"	\
		"mmcinfo; mmc dev 1; mmc read $load_addr "		\
		"$kernel_addr_sd $kernel_size_sd && "	\
		"env exists secureboot && mmc read $kernelheader_addr_r " \
		"$kernelhdr_addr_sd $kernelhdr_size_sd "		\
		" && esbc_validate ${kernelheader_addr_r};"	\
		"bootm $load_addr#$board\0"			\
	"emmc_hdploadcmd=echo Trying load HDP firmware from EMMC..;"      \
		"mmc dev 1;mmcinfo;mmc read $load_addr 0x4a00 0x200 "	\
		"&& hdp load $load_addr 0x2000\0"

#undef CONFIG_BOOTCOMMAND

#define XSPI_NOR_BOOTCOMMAND	\
	"run xspi_hdploadcmd; run distro_bootcmd; run xspi_bootcmd; " \
	"env exists secureboot && esbc_halt;;"
#define SD_BOOTCOMMAND	\
	"run sd_hdploadcmd; run distro_bootcmd;run sd_bootcmd; " \
	"env exists secureboot && esbc_halt;"
#define SD2_BOOTCOMMAND	\
	"run emmc_hdploadcmd; run distro_bootcmd;run emmc_bootcmd; " \
	"env exists secureboot && esbc_halt;"

/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
					sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE /* Boot args buffer */

#ifndef CONFIG_CMDLINE_EDITING
#define CONFIG_CMDLINE_EDITING		1
#endif

#define CONFIG_SYS_MAXARGS		64	/* max command args */

#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */

/*  MMC  */
#ifdef CONFIG_MMC
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
#endif

#define CONFIG_SYS_MMC_ENV_DEV         0
#define OCRAM_NONSECURE_SIZE		0x00010000
#define CONFIG_SYS_FSL_QSPI_BASE	0x20000000

#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE

/* I2C bus multiplexer */
#define I2C_MUX_PCA_ADDR_PRI            0x77 /* Primary Mux*/
#define I2C_MUX_CH_DEFAULT              0x8

/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM		0
#define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5

#ifdef CONFIG_NXP_ESBC
#include <asm/fsl_secure_boot.h>
#endif

/* Ethernet */
/* smallest ENETC BD ring has 8 entries */
#define CONFIG_SYS_RX_ETH_BUFFER		8

#endif /* __L1028A_COMMON_H */