| /* |
| * Copyright (C) 2010 Andreas Bießmann <biessmann.devel@googlemail.com> |
| * |
| * based on previous work by |
| * |
| * Ulf Samuelsson <ulf@atmel.com> |
| * Rick Bronson <rick@efn.org> |
| * |
| * Configuration settings for the AT91RM9200EK board. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __AT91RM9200EK_CONFIG_H__ |
| #define __AT91RM9200EK_CONFIG_H__ |
| |
| #include <linux/sizes.h> |
| |
| /* |
| * set some initial configurations depending on configure target |
| * |
| * at91rm9200ek_config -> boot from 0x0 in NOR Flash at CS0 |
| * at91rm9200ek_ram_config -> continue booting from 0x20100000 in RAM; lowlevel |
| * initialisation was done by some preloader |
| */ |
| #ifdef CONFIG_RAMBOOT |
| #define CONFIG_SKIP_LOWLEVEL_INIT |
| #define CONFIG_SYS_TEXT_BASE 0x20100000 |
| #else |
| #define CONFIG_SYS_TEXT_BASE 0x10000000 |
| #endif |
| |
| /* |
| * AT91C_XTAL_CLOCK is the frequency of external xtal in hertz |
| * AT91C_MAIN_CLOCK is the frequency of PLLA output |
| * AT91C_MASTER_CLOCK is the peripherial clock |
| * CONFIG_SYS_HZ_CLOCK is the value for CCR in tc0 (divider 2 is implicitely |
| * set in arch/arm/cpu/arm920t/at91/timer.c) |
| * CONFIG_SYS_HZ is the tick rate for timer tc0 |
| */ |
| #define AT91C_XTAL_CLOCK 18432000 |
| #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 |
| #define AT91C_MAIN_CLOCK ((AT91C_XTAL_CLOCK / 4) * 39) |
| #define AT91C_MASTER_CLOCK (AT91C_MAIN_CLOCK / 3 ) |
| #define CONFIG_SYS_HZ_CLOCK (AT91C_MASTER_CLOCK / 2) |
| |
| /* CPU configuration */ |
| #define CONFIG_AT91RM9200 |
| #define CONFIG_AT91RM9200EK |
| #define CONFIG_CPUAT91 |
| #define USE_920T_MMU |
| |
| #include <asm/hardware.h> /* needed for port definitions */ |
| |
| #define CONFIG_CMDLINE_TAG |
| #define CONFIG_SETUP_MEMORY_TAGS |
| #define CONFIG_INITRD_TAG |
| |
| #define CONFIG_BOARD_EARLY_INIT_F |
| |
| /* |
| * Memory Configuration |
| */ |
| #define CONFIG_NR_DRAM_BANKS 1 |
| #define CONFIG_SYS_SDRAM_BASE 0x20000000 |
| #define CONFIG_SYS_SDRAM_SIZE SZ_32M |
| |
| #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE |
| #define CONFIG_SYS_MEMTEST_END \ |
| (CONFIG_SYS_MEMTEST_START + CONFIG_SYS_SDRAM_SIZE - SZ_256K) |
| |
| /* |
| * LowLevel Init |
| */ |
| #ifndef CONFIG_SKIP_LOWLEVEL_INIT |
| #define CONFIG_SYS_USE_MAIN_OSCILLATOR |
| /* flash */ |
| #define CONFIG_SYS_EBI_CFGR_VAL 0x00000000 |
| #define CONFIG_SYS_SMC_CSR0_VAL 0x00003284 /* 16bit, 2 TDF, 4 WS */ |
| |
| /* clocks */ |
| #define CONFIG_SYS_PLLAR_VAL 0x20263E04 /* 179.712000 MHz for PCK */ |
| #define CONFIG_SYS_PLLBR_VAL 0x10483E0E /* 48.054857 MHz (divider by 2 for USB) */ |
| /* PCK/3 = MCK Master Clock = 59.904000MHz from PLLA */ |
| #define CONFIG_SYS_MCKR_VAL 0x00000202 |
| |
| /* sdram */ |
| #define CONFIG_SYS_PIOC_ASR_VAL 0xFFFF0000 /* Configure PIOC as peripheral (D16/D31) */ |
| #define CONFIG_SYS_PIOC_BSR_VAL 0x00000000 |
| #define CONFIG_SYS_PIOC_PDR_VAL 0xFFFF0000 |
| #define CONFIG_SYS_EBI_CSA_VAL 0x00000002 /* CS1=CONFIG_SYS_SDRAM */ |
| #define CONFIG_SYS_SDRC_CR_VAL 0x2188c155 /* set up the CONFIG_SYS_SDRAM */ |
| #define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE /* address of the SDRAM */ |
| #define CONFIG_SYS_SDRAM1 (CONFIG_SYS_SDRAM_BASE+0x80) |
| #define CONFIG_SYS_SDRAM_VAL 0x00000000 /* value written to CONFIG_SYS_SDRAM */ |
| #define CONFIG_SYS_SDRC_MR_VAL 0x00000002 /* Precharge All */ |
| #define CONFIG_SYS_SDRC_MR_VAL1 0x00000004 /* refresh */ |
| #define CONFIG_SYS_SDRC_MR_VAL2 0x00000003 /* Load Mode Register */ |
| #define CONFIG_SYS_SDRC_MR_VAL3 0x00000000 /* Normal Mode */ |
| #define CONFIG_SYS_SDRC_TR_VAL 0x000002E0 /* Write refresh rate */ |
| #endif /* CONFIG_SKIP_LOWLEVEL_INIT */ |
| |
| /* |
| * Hardware drivers |
| */ |
| /* |
| * Choose a USART for serial console |
| * CONFIG_DBGU is DBGU unit on J10 |
| * CONFIG_USART1 is USART1 on J14 |
| */ |
| #define CONFIG_ATMEL_USART |
| #define CONFIG_USART_BASE ATMEL_BASE_DBGU |
| #define CONFIG_USART_ID 0/* ignored in arm */ |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| /* |
| * Command line configuration. |
| */ |
| |
| /* |
| * Network Driver Setting |
| */ |
| #define CONFIG_DRIVER_AT91EMAC |
| #define CONFIG_SYS_RX_ETH_BUFFER 16 |
| #define CONFIG_RMII |
| #define CONFIG_MII |
| |
| /* |
| * NOR Flash |
| */ |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_BASE 0x10000000 |
| #define PHYS_FLASH_1 CONFIG_SYS_FLASH_BASE |
| #define PHYS_FLASH_SIZE SZ_8M |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 |
| #define CONFIG_SYS_FLASH_PROTECTION |
| |
| /* |
| * USB Config |
| */ |
| #define CONFIG_USB_ATMEL 1 |
| #define CONFIG_USB_ATMEL_CLK_SEL_PLLB |
| #define CONFIG_USB_OHCI_NEW 1 |
| #define CONFIG_USB_KEYBOARD 1 |
| #define CONFIG_USB_STORAGE 1 |
| #define CONFIG_DOS_PARTITION 1 |
| |
| #define CONFIG_SYS_USB_OHCI_CPU_INIT 1 |
| #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_USB_HOST_BASE |
| #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91rm9200" |
| #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 |
| |
| /* |
| * Environment Settings |
| */ |
| #define CONFIG_ENV_IS_IN_FLASH |
| |
| /* |
| * after u-boot.bin |
| */ |
| #define CONFIG_ENV_ADDR \ |
| (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) |
| #define CONFIG_ENV_SIZE SZ_64K /* sectors are 64K here */ |
| /* The following #defines are needed to get flash environment right */ |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_MONITOR_LEN SZ_256K |
| |
| /* |
| * Boot option |
| */ |
| #define CONFIG_BOOTDELAY 3 |
| |
| /* default load address */ |
| #define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE + SZ_16M |
| #define CONFIG_ENV_OVERWRITE |
| |
| /* |
| * Shell Settings |
| */ |
| #define CONFIG_CMDLINE_EDITING |
| #define CONFIG_SYS_LONGHELP |
| #define CONFIG_AUTO_COMPLETE |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| /* Print Buffer Size */ |
| #define CONFIG_SYS_PBSIZE \ |
| (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) |
| |
| /* |
| * Size of malloc() pool |
| */ |
| #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + SZ_128K, \ |
| SZ_4K) |
| |
| #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_4K \ |
| - GENERATED_GBL_DATA_SIZE) |
| |
| #endif /* __AT91RM9200EK_CONFIG_H__ */ |