| /* |
| * Board specific setup info |
| * |
| * (C) Copyright 2003 |
| * Texas Instruments, <www.ti.com> |
| * |
| * -- Some bits of code used from rrload's head_OMAP1510.s -- |
| * Copyright (C) 2002 RidgeRun, Inc. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #include <config.h> |
| #include <version.h> |
| |
| #if defined(CONFIG_OMAP1510) |
| #include <./configs/omap1510.h> |
| #endif |
| |
| #define OMAP1510_CLKS ((1<<EN_XORPCK)|(1<<EN_PERCK)|(1<<EN_TIMCK)|(1<<EN_GPIOCK)) |
| |
| |
| _TEXT_BASE: |
| .word CONFIG_SYS_TEXT_BASE /* sdram load addr from config.mk */ |
| |
| .globl lowlevel_init |
| lowlevel_init: |
| |
| /* |
| * Configure 1510 pins functions to match our board. |
| */ |
| ldr r0, REG_PULL_DWN_CTRL_0 |
| ldr r1, VAL_PULL_DWN_CTRL_0 |
| str r1, [r0] |
| ldr r0, REG_PULL_DWN_CTRL_1 |
| ldr r1, VAL_PULL_DWN_CTRL_1 |
| str r1, [r0] |
| ldr r0, REG_PULL_DWN_CTRL_2 |
| ldr r1, VAL_PULL_DWN_CTRL_2 |
| str r1, [r0] |
| ldr r0, REG_PULL_DWN_CTRL_3 |
| ldr r1, VAL_PULL_DWN_CTRL_3 |
| str r1, [r0] |
| ldr r0, REG_FUNC_MUX_CTRL_4 |
| ldr r1, VAL_FUNC_MUX_CTRL_4 |
| str r1, [r0] |
| ldr r0, REG_FUNC_MUX_CTRL_5 |
| ldr r1, VAL_FUNC_MUX_CTRL_5 |
| str r1, [r0] |
| ldr r0, REG_FUNC_MUX_CTRL_6 |
| ldr r1, VAL_FUNC_MUX_CTRL_6 |
| str r1, [r0] |
| ldr r0, REG_FUNC_MUX_CTRL_7 |
| ldr r1, VAL_FUNC_MUX_CTRL_7 |
| str r1, [r0] |
| ldr r0, REG_FUNC_MUX_CTRL_8 |
| ldr r1, VAL_FUNC_MUX_CTRL_8 |
| str r1, [r0] |
| ldr r0, REG_FUNC_MUX_CTRL_9 |
| ldr r1, VAL_FUNC_MUX_CTRL_9 |
| str r1, [r0] |
| ldr r0, REG_FUNC_MUX_CTRL_A |
| ldr r1, VAL_FUNC_MUX_CTRL_A |
| str r1, [r0] |
| ldr r0, REG_FUNC_MUX_CTRL_B |
| ldr r1, VAL_FUNC_MUX_CTRL_B |
| str r1, [r0] |
| ldr r0, REG_FUNC_MUX_CTRL_C |
| ldr r1, VAL_FUNC_MUX_CTRL_C |
| str r1, [r0] |
| ldr r0, REG_FUNC_MUX_CTRL_D |
| ldr r1, VAL_FUNC_MUX_CTRL_D |
| str r1, [r0] |
| ldr r0, REG_VOLTAGE_CTRL_0 |
| ldr r1, VAL_VOLTAGE_CTRL_0 |
| str r1, [r0] |
| ldr r0, REG_TEST_DBG_CTRL_0 |
| ldr r1, VAL_TEST_DBG_CTRL_0 |
| str r1, [r0] |
| ldr r0, REG_MOD_CONF_CTRL_0 |
| ldr r1, VAL_MOD_CONF_CTRL_0 |
| str r1, [r0] |
| |
| /* Move to 1510 mode */ |
| ldr r0, REG_COMP_MODE_CTRL_0 |
| ldr r1, VAL_COMP_MODE_CTRL_0 |
| str r1, [r0] |
| |
| /* Set up Traffic Ctlr*/ |
| ldr r0, REG_TC_IMIF_PRIO |
| mov r1, #0x0 |
| str r1, [r0] |
| ldr r0, REG_TC_EMIFS_PRIO |
| str r1, [r0] |
| ldr r0, REG_TC_EMIFF_PRIO |
| str r1, [r0] |
| |
| ldr r0, REG_TC_EMIFS_CONFIG |
| ldr r1, [r0] |
| bic r1, r1, #0x08 /* clear the global power-down enable PDE bit */ |
| bic r1, r1, #0x01 /* write protect flash by clearing the WP bit */ |
| str r1, [r0] /* EMIFS GlB Configuration. (value 0x12 most likely) */ |
| |
| /* Setup some clock domains */ |
| ldr r1, =OMAP1510_CLKS |
| ldr r0, REG_ARM_IDLECT2 |
| strh r1, [r0] /* CLKM, Clock domain control. */ |
| |
| mov r1, #0x01 /* PER_EN bit */ |
| ldr r0, REG_ARM_RSTCT2 |
| strh r1, [r0] /* CLKM; Peripheral reset. */ |
| |
| /* Set CLKM to Sync-Scalable */ |
| /* I supposidly need to enable the dsp clock before switching */ |
| mov r1, #0x1000 |
| ldr r0, REG_ARM_SYSST |
| strh r1, [r0] |
| mov r0, #0x400 |
| 1: |
| subs r0, r0, #0x1 /* wait for any bubbles to finish */ |
| bne 1b |
| |
| ldr r1, VAL_ARM_CKCTL /* use 12Mhz ref, PER must be <= 50Mhz so /2 */ |
| ldr r0, REG_ARM_CKCTL |
| strh r1, [r0] |
| |
| /* setup DPLL 1 */ |
| ldr r1, VAL_DPLL1_CTL |
| ldr r0, REG_DPLL1_CTL |
| strh r1, [r0] |
| ands r1, r1, #0x10 /* Check if PLL is enabled. */ |
| beq lock_end /* Do not look for lock if BYPASS selected */ |
| 2: |
| ldrh r1, [r0] |
| ands r1, r1, #0x01 /* Check the LOCK bit. */ |
| beq 2b /* ...loop until bit goes hi. */ |
| lock_end: |
| |
| /* Set memory timings corresponding to the new clock speed */ |
| |
| /* Check execution location to determine current execution location |
| * and branch to appropriate initialization code. |
| */ |
| mov r0, #0x10000000 /* Load physical SDRAM base. */ |
| mov r1, pc /* Get current execution location. */ |
| /* Zero all but top 6 bits of PC, as they alone detect whether an |
| * address is in the range 0x1000:0000-0x13ff:ffff, the 64M sized |
| * valid range for SDRAM on the OMAP 1510/5910. |
| */ |
| and r1, r1, #0xfc000000 |
| cmp r1, r0 /* Compare. */ |
| beq skip_sdram /* Skip over EMIF-fast initialization |
| * if running from SDRAM. |
| */ |
| |
| /* |
| * Delay for SDRAM initialization. |
| */ |
| mov r3, #0x1800 /* value should be checked */ |
| 3: |
| subs r3, r3, #0x1 /* Decrement count */ |
| bne 3b |
| |
| /* |
| * Set SDRAM control values. Disable refresh before MRS command. |
| */ |
| ldr r0, VAL_TC_EMIFF_SDRAM_CONFIG /* get good value */ |
| bic r3, r0, #0xC /* (BIT3|BIT2) ulConfig with auto-refresh disabled. */ |
| orr r3, r3, #0x8000000 /* (BIT27) Disable CLK when Power down or Self-Refresh */ |
| orr r3, r3, #0x4000000 /* BIT26 Power Down Enable */ |
| ldr r2, REG_TC_EMIFF_SDRAM_CONFIG /* Point to configuration register. */ |
| str r3, [r2] /* Store the passed value with AR disabled. */ |
| |
| ldr r1, VAL_TC_EMIFF_MRS /* get MRS value */ |
| ldr r2, REG_TC_EMIFF_MRS /* Point to MRS register. */ |
| str r1, [r2] /* Store the passed value.*/ |
| |
| ldr r2, REG_TC_EMIFF_SDRAM_CONFIG /* Point to configuration register. */ |
| str r0, [r2] /* Store the passed value. */ |
| |
| /* |
| * Delay for SDRAM initialization. |
| */ |
| mov r3, #0x1800 |
| 4: |
| subs r3, r3, #1 /* Decrement count. */ |
| bne 4b |
| |
| skip_sdram: |
| |
| /* slow interface */ |
| ldr r1, VAL_TC_EMIFS_CS0_CONFIG |
| ldr r0, REG_TC_EMIFS_CS0_CONFIG |
| str r1, [r0] /* Chip Select 0 */ |
| ldr r1, VAL_TC_EMIFS_CS1_CONFIG |
| ldr r0, REG_TC_EMIFS_CS1_CONFIG |
| str r1, [r0] /* Chip Select 1 */ |
| ldr r1, VAL_TC_EMIFS_CS2_CONFIG |
| ldr r0, REG_TC_EMIFS_CS2_CONFIG |
| str r1, [r0] /* Chip Select 2 */ |
| ldr r1, VAL_TC_EMIFS_CS3_CONFIG |
| ldr r0, REG_TC_EMIFS_CS3_CONFIG |
| str r1, [r0] /* Chip Select 3 */ |
| |
| /* Next, Enable the RS232 Line Drivers in the FPGA. */ |
| /* Also, power on the audio CODEC's amplifier here, */ |
| /* which will make a noise on the audio output. */ |
| /* This is done here instead of in the kernel so there */ |
| /* isn't a loud popping noise at the start of each */ |
| /* song. */ |
| /* Also, disable the CODEC's clocks. */ |
| /* omap1510-HelenP1 [specific] */ |
| |
| ldr r0, REG_FPGA_POWER |
| mov r1, #0 |
| ldr r2, REG_FPGA_DIP_SWITCH |
| ldrb r3, [r2] |
| cmp r3, #0x8 |
| movne r1, #0x62 /* Enable the RS232 Line Drivers in the EPLD */ |
| strb r1, [r0] |
| ldr r0, REG_FPGA_AUDIO |
| mov r1, #0x0 /* Disable sound driver (CODEC clocks) */ |
| strb r1, [r0] |
| |
| /* back to arch calling code */ |
| mov pc, lr |
| |
| /* the literal pools origin */ |
| .ltorg |
| |
| /* OMAP configuration registers */ |
| REG_FUNC_MUX_CTRL_0: /* 32 bits */ |
| .word 0xfffe1000 |
| REG_FUNC_MUX_CTRL_1: /* 32 bits */ |
| .word 0xfffe1004 |
| REG_FUNC_MUX_CTRL_2: /* 32 bits */ |
| .word 0xfffe1008 |
| REG_COMP_MODE_CTRL_0: /* 32 bits */ |
| .word 0xfffe100c |
| REG_FUNC_MUX_CTRL_3: /* 32 bits */ |
| .word 0xfffe1010 |
| REG_FUNC_MUX_CTRL_4: /* 32 bits */ |
| .word 0xfffe1014 |
| REG_FUNC_MUX_CTRL_5: /* 32 bits */ |
| .word 0xfffe1018 |
| REG_FUNC_MUX_CTRL_6: /* 32 bits */ |
| .word 0xfffe101c |
| REG_FUNC_MUX_CTRL_7: /* 32 bits */ |
| .word 0xfffe1020 |
| REG_FUNC_MUX_CTRL_8: /* 32 bits */ |
| .word 0xfffe1024 |
| REG_FUNC_MUX_CTRL_9: /* 32 bits */ |
| .word 0xfffe1028 |
| REG_FUNC_MUX_CTRL_A: /* 32 bits */ |
| .word 0xfffe102C |
| REG_FUNC_MUX_CTRL_B: /* 32 bits */ |
| .word 0xfffe1030 |
| REG_FUNC_MUX_CTRL_C: /* 32 bits */ |
| .word 0xfffe1034 |
| REG_FUNC_MUX_CTRL_D: /* 32 bits */ |
| .word 0xfffe1038 |
| REG_PULL_DWN_CTRL_0: /* 32 bits */ |
| .word 0xfffe1040 |
| REG_PULL_DWN_CTRL_1: /* 32 bits */ |
| .word 0xfffe1044 |
| REG_PULL_DWN_CTRL_2: /* 32 bits */ |
| .word 0xfffe1048 |
| REG_PULL_DWN_CTRL_3: /* 32 bits */ |
| .word 0xfffe104c |
| REG_VOLTAGE_CTRL_0: /* 32 bits */ |
| .word 0xfffe1060 |
| REG_TEST_DBG_CTRL_0: /* 32 bits */ |
| .word 0xfffe1070 |
| REG_MOD_CONF_CTRL_0: /* 32 bits */ |
| .word 0xfffe1080 |
| REG_TC_IMIF_PRIO: /* 32 bits */ |
| .word 0xfffecc00 |
| REG_TC_EMIFS_PRIO: /* 32 bits */ |
| .word 0xfffecc04 |
| REG_TC_EMIFF_PRIO: /* 32 bits */ |
| .word 0xfffecc08 |
| REG_TC_EMIFS_CONFIG: /* 32 bits */ |
| .word 0xfffecc0c |
| REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */ |
| .word 0xfffecc10 |
| REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */ |
| .word 0xfffecc14 |
| REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */ |
| .word 0xfffecc18 |
| REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */ |
| .word 0xfffecc1c |
| REG_TC_EMIFF_SDRAM_CONFIG: /* 32 bits */ |
| .word 0xfffecc20 |
| REG_TC_EMIFF_MRS: /* 32 bits */ |
| .word 0xfffecc24 |
| /* MPU clock/reset/power mode control registers */ |
| REG_ARM_CKCTL: /* 16 bits */ |
| .word 0xfffece00 |
| REG_ARM_IDLECT2: /* 16 bits */ |
| .word 0xfffece08 |
| REG_ARM_RSTCT2: /* 16 bits */ |
| .word 0xfffece14 |
| REG_ARM_SYSST: /* 16 bits */ |
| .word 0xfffece18 |
| /* DPLL control registers */ |
| REG_DPLL1_CTL: /* 16 bits */ |
| .word 0xfffecf00 |
| /* identification code register */ |
| REG_IDCODE: /* 32 bits */ |
| .word 0xfffed404 |
| |
| /* Innovator specific */ |
| REG_FPGA_LED_DIGIT: /* 8 bits (not used on Innovator) */ |
| .word 0x08000003 |
| REG_FPGA_POWER: /* 8 bits */ |
| .word 0x08000005 |
| REG_FPGA_AUDIO: /* 8 bits (not used on Innovator) */ |
| .word 0x0800000c |
| REG_FPGA_DIP_SWITCH: /* 8 bits (not used on Innovator) */ |
| .word 0x0800000e |
| |
| VAL_COMP_MODE_CTRL_0: |
| .word 0x0000eaef |
| VAL_FUNC_MUX_CTRL_4: |
| .word 0x00000000 |
| VAL_FUNC_MUX_CTRL_5: |
| .word 0x00000000 |
| VAL_FUNC_MUX_CTRL_6: |
| .word 0x00000001 |
| VAL_FUNC_MUX_CTRL_7: |
| .word 0x00000000 |
| VAL_FUNC_MUX_CTRL_8: |
| .word 0x10001200 |
| VAL_FUNC_MUX_CTRL_9: |
| .word 0x01201012 |
| VAL_FUNC_MUX_CTRL_A: |
| .word 0x00000248 |
| VAL_FUNC_MUX_CTRL_B: |
| .word 0x00000248 |
| VAL_FUNC_MUX_CTRL_C: |
| .word 0x09000000 |
| VAL_FUNC_MUX_CTRL_D: |
| .word 0x00000000 |
| VAL_PULL_DWN_CTRL_0: |
| .word 0x11a10000 |
| VAL_PULL_DWN_CTRL_1: |
| .word 0x2e047fff |
| VAL_PULL_DWN_CTRL_2: |
| .word 0xffd603a6 |
| VAL_PULL_DWN_CTRL_3: |
| .word 0x00003e03 |
| VAL_VOLTAGE_CTRL_0: |
| .word 0x00000007 |
| VAL_TEST_DBG_CTRL_0: |
| /* See Errata 4.13, This works around a SRAM bug, for chips below ES2.5 . |
| * This slows down internal SRAM accesses. |
| */ |
| .word 0x00000007 |
| VAL_MOD_CONF_CTRL_0: |
| .word 0x0b000008 |
| VAL_ARM_CKCTL: |
| .word 0x010f |
| VAL_DPLL1_CTL: |
| .word 0x2710 |
| VAL_TC_EMIFS_CS1_CONFIG_PRELIM: |
| .word 0x00001149 |
| VAL_TC_EMIFS_CS2_CONFIG_PRELIM: |
| .word 0x00004158 |
| VAL_TC_EMIFS_CS0_CONFIG: |
| .word 0x002130b0 |
| VAL_TC_EMIFS_CS1_CONFIG: |
| .word 0x0000f559 |
| VAL_TC_EMIFS_CS2_CONFIG: |
| .word 0x000055f0 |
| VAL_TC_EMIFS_CS3_CONFIG: |
| .word 0x00003331 |
| VAL_TC_EMIFF_SDRAM_CONFIG: |
| .word 0x010290fc |
| VAL_TC_EMIFF_MRS: |
| .word 0x00000027 |