include/configs/xilinx_zynqmp.h - platform/external/u-boot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Configuration for Xilinx ZynqMP
  * (C) Copyright 2014 - 2015 Xilinx, Inc.
  * Michal Simek <michal.simek@xilinx.com>
  *
  * Based on Configuration for Versatile Express
  */

 #ifndef __XILINX_ZYNQMP_H
 #define __XILINX_ZYNQMP_H

 #define CONFIG_REMAKE_ELF

 /* #define CONFIG_ARMV8_SWITCH_TO_EL1 */

 /* Generic Interrupt Controller Definitions */
 #define CONFIG_GICV2
 #define GICD_BASE	0xF9010000
 #define GICC_BASE	0xF9020000

 #ifndef CONFIG_SYS_MEMTEST_SCRATCH
 # define CONFIG_SYS_MEMTEST_SCRATCH	0x10800000
 #endif

 #ifndef CONFIG_NR_DRAM_BANKS
 # define CONFIG_NR_DRAM_BANKS		2
 #endif
 #define CONFIG_SYS_MEMTEST_START	0
 #define CONFIG_SYS_MEMTEST_END		1000

 #define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_TEXT_BASE

 /* Generic Timer Definitions - setup in EL3. Setup by ATF for other cases */
 #if !defined(COUNTER_FREQUENCY)
 # define COUNTER_FREQUENCY		100000000
 #endif

 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 0x2000000)

 /* Serial setup */
 #define CONFIG_ARM_DCC
 #define CONFIG_CPU_ARMV8

 #define CONFIG_SYS_BAUDRATE_TABLE \
 	{ 4800, 9600, 19200, 38400, 57600, 115200 }

 /* BOOTP options */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_MAY_FAIL

 #if defined(CONFIG_MMC_SDHCI_ZYNQ)
 # define CONFIG_SUPPORT_EMMC_BOOT
 #endif

 #ifdef CONFIG_NAND_ARASAN
 # define CONFIG_SYS_MAX_NAND_DEVICE	1
 # define CONFIG_SYS_NAND_ONFI_DETECTION
 # define CONFIG_MTD_DEVICE
 #endif

 #if defined(CONFIG_SPL_BUILD)
 #define CONFIG_ZYNQMP_PSU_INIT_ENABLED
 #endif

 /* Miscellaneous configurable options */
 #define CONFIG_SYS_LOAD_ADDR		0x8000000

 #if defined(CONFIG_ZYNQMP_USB)
 #define CONFIG_SYS_DFU_DATA_BUF_SIZE	0x1800000
 #define DFU_DEFAULT_POLL_TIMEOUT	300
 #define CONFIG_USB_CABLE_CHECK
 #define CONFIG_THOR_RESET_OFF
 #define DFU_ALT_INFO_RAM \
 	"dfu_ram_info=" \
 	"setenv dfu_alt_info " \
 	"Image ram $kernel_addr $kernel_size\\\\;" \
 	"system.dtb ram $fdt_addr $fdt_size\0" \
 	"dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \
 	"thor_ram=run dfu_ram_info && thordown 0 ram 0\0"

 #define DFU_ALT_INFO  \
 		DFU_ALT_INFO_RAM

 #ifndef CONFIG_SPL_BUILD
 # define PARTS_DEFAULT \
 	"partitions=uuid_disk=${uuid_gpt_disk};" \
 	"name=""boot"",size=16M,uuid=${uuid_gpt_boot};" \
 	"name=""Linux"",size=-M,uuid=${uuid_gpt_Linux}\0"
 #endif
 #endif

 #if !defined(DFU_ALT_INFO)
 # define DFU_ALT_INFO
 #endif

 #if !defined(PARTS_DEFAULT)
 # define PARTS_DEFAULT
 #endif

 /* Monitor Command Prompt */
 /* Console I/O Buffer Size */
 #define CONFIG_SYS_CBSIZE		2048
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
 #define CONFIG_PANIC_HANG
 #define CONFIG_SYS_MAXARGS		64

 /* Ethernet driver */
 #if defined(CONFIG_ZYNQ_GEM)
 # define CONFIG_MII
 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
 # define PHY_ANEG_TIMEOUT       20000
 #endif

 /* I2C */
 #if defined(CONFIG_SYS_I2C_ZYNQ)
 # define CONFIG_SYS_I2C
 #endif

 /* EEPROM */
 #ifdef CONFIG_ZYNQMP_EEPROM
 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
 # define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
 # define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
 # define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
 # define CONFIG_SYS_EEPROM_SIZE			(64 * 1024)
 #endif

 #ifdef CONFIG_SATA_CEVA
 #define CONFIG_SYS_SCSI_MAX_SCSI_ID	2
 #define CONFIG_SYS_SCSI_MAX_LUN		1
 #define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 					 CONFIG_SYS_SCSI_MAX_LUN)
 #endif

 #define CONFIG_SYS_BOOTM_LEN	(60 * 1024 * 1024)

 #define CONFIG_CLOCKS

 #define ENV_MEM_LAYOUT_SETTINGS \
 	"fdt_high=10000000\0" \
 	"initrd_high=10000000\0" \
 	"fdt_addr_r=0x40000000\0" \
 	"pxefile_addr_r=0x10000000\0" \
 	"kernel_addr_r=0x18000000\0" \
 	"scriptaddr=0x02000000\0" \
 	"ramdisk_addr_r=0x02100000\0" \

 #if defined(CONFIG_MMC_SDHCI_ZYNQ)
 # define BOOT_TARGET_DEVICES_MMC(func)	func(MMC, mmc, 0) func(MMC, mmc, 1)
 #else
 # define BOOT_TARGET_DEVICES_MMC(func)
 #endif

 #if defined(CONFIG_SATA_CEVA)
 # define BOOT_TARGET_DEVICES_SCSI(func)	func(SCSI, scsi, 0)
 #else
 # define BOOT_TARGET_DEVICES_SCSI(func)
 #endif

 #if defined(CONFIG_ZYNQMP_USB)
 # define BOOT_TARGET_DEVICES_USB(func)	func(USB, usb, 0) func(USB, usb, 1)
 #else
 # define BOOT_TARGET_DEVICES_USB(func)
 #endif

 #if defined(CONFIG_CMD_PXE) && defined(CONFIG_CMD_DHCP)
 # define BOOT_TARGET_DEVICES_PXE(func)	func(PXE, pxe, na)
 #else
 # define BOOT_TARGET_DEVICES_PXE(func)
 #endif

 #if defined(CONFIG_CMD_DHCP)
 # define BOOT_TARGET_DEVICES_DHCP(func)	func(DHCP, dhcp, na)
 #else
 # define BOOT_TARGET_DEVICES_DHCP(func)
 #endif

 #define BOOT_TARGET_DEVICES(func) \
 	BOOT_TARGET_DEVICES_MMC(func) \
 	BOOT_TARGET_DEVICES_USB(func) \
 	BOOT_TARGET_DEVICES_SCSI(func) \
 	BOOT_TARGET_DEVICES_PXE(func) \
 	BOOT_TARGET_DEVICES_DHCP(func)

 #include <config_distro_bootcmd.h>

 /* Initial environment variables */
 #ifndef CONFIG_EXTRA_ENV_SETTINGS
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	ENV_MEM_LAYOUT_SETTINGS \
 	BOOTENV \
 	DFU_ALT_INFO
 #endif

 /* SPL can't handle all huge variables - define just DFU */
 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_DFU_SUPPORT)
 #undef CONFIG_EXTRA_ENV_SETTINGS
 # define CONFIG_EXTRA_ENV_SETTINGS \
 	"dfu_alt_info_ram=uboot.bin ram 0x8000000 0x1000000;" \
 			  "atf-uboot.ub ram 0x10000000 0x1000000;" \
 			  "Image ram 0x80000 0x3f80000;" \
 			  "system.dtb ram 0x4000000 0x100000\0" \
 	"dfu_bufsiz=0x1000\0"
 #endif

 #define CONFIG_SPL_TEXT_BASE		0xfffc0000
 #define CONFIG_SPL_STACK		0xfffffffc
 #define CONFIG_SPL_MAX_SIZE		0x40000

 /* Just random location in OCM */
 #define CONFIG_SPL_BSS_START_ADDR	0x0
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000

 #if defined(CONFIG_SPL_SPI_FLASH_SUPPORT)
 # define CONFIG_SYS_SPI_KERNEL_OFFS	0x80000
 # define CONFIG_SYS_SPI_ARGS_OFFS	0xa0000
 # define CONFIG_SYS_SPI_ARGS_SIZE	0xa0000

 # define CONFIG_SYS_SPI_U_BOOT_OFFS	0x170000
 #endif

 /* u-boot is like dtb */
 #define CONFIG_SPL_FS_LOAD_ARGS_NAME	"u-boot.bin"
 #define CONFIG_SYS_SPL_ARGS_ADDR	0x8000000

 /* ATF is my kernel image */
 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME	"atf-uboot.ub"

 /* FIT load address for RAM boot */
 #define CONFIG_SPL_LOAD_FIT_ADDRESS	0x10000000

 /* MMC support */
 #ifdef CONFIG_MMC_SDHCI_ZYNQ
 # define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
 # define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR	0 /* unused */
 # define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS	0 /* unused */
 # define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR	0 /* unused */
 # define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME	"u-boot.img"
 #endif

 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_DFU_SUPPORT)
 # undef CONFIG_CMD_BOOTD
 # define CONFIG_SPL_ENV_SUPPORT
 # define CONFIG_SPL_HASH_SUPPORT
 # define CONFIG_ENV_MAX_ENTRIES	10
 #endif

 #define CONFIG_SYS_SPL_MALLOC_START	0x20000000
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000

 #ifdef CONFIG_SPL_SYS_MALLOC_SIMPLE
 # error "Disable CONFIG_SPL_SYS_MALLOC_SIMPLE. Full malloc needs to be used"
 #endif

 #define CONFIG_BOARD_EARLY_INIT_F

 #endif /* __XILINX_ZYNQMP_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Configuration for Xilinx ZynqMP
	* (C) Copyright 2014 - 2015 Xilinx, Inc.
	* Michal Simek <michal.simek@xilinx.com>
	*
	* Based on Configuration for Versatile Express
	*/

	#ifndef __XILINX_ZYNQMP_H
	#define __XILINX_ZYNQMP_H

	#define CONFIG_REMAKE_ELF

	/* #define CONFIG_ARMV8_SWITCH_TO_EL1 */

	/* Generic Interrupt Controller Definitions */
	#define CONFIG_GICV2
	#define GICD_BASE 0xF9010000
	#define GICC_BASE 0xF9020000

	#ifndef CONFIG_SYS_MEMTEST_SCRATCH
	# define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
	#endif

	#ifndef CONFIG_NR_DRAM_BANKS
	# define CONFIG_NR_DRAM_BANKS 2
	#endif
	#define CONFIG_SYS_MEMTEST_START 0
	#define CONFIG_SYS_MEMTEST_END 1000

	#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE

	/* Generic Timer Definitions - setup in EL3. Setup by ATF for other cases */
	#if !defined(COUNTER_FREQUENCY)
	# define COUNTER_FREQUENCY 100000000
	#endif

	/* Size of malloc() pool */
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 0x2000000)

	/* Serial setup */
	#define CONFIG_ARM_DCC
	#define CONFIG_CPU_ARMV8

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{ 4800, 9600, 19200, 38400, 57600, 115200 }

	/* BOOTP options */
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_MAY_FAIL

	#if defined(CONFIG_MMC_SDHCI_ZYNQ)
	# define CONFIG_SUPPORT_EMMC_BOOT
	#endif

	#ifdef CONFIG_NAND_ARASAN
	# define CONFIG_SYS_MAX_NAND_DEVICE 1
	# define CONFIG_SYS_NAND_ONFI_DETECTION
	# define CONFIG_MTD_DEVICE
	#endif

	#if defined(CONFIG_SPL_BUILD)
	#define CONFIG_ZYNQMP_PSU_INIT_ENABLED
	#endif

	/* Miscellaneous configurable options */
	#define CONFIG_SYS_LOAD_ADDR 0x8000000

	#if defined(CONFIG_ZYNQMP_USB)
	#define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x1800000
	#define DFU_DEFAULT_POLL_TIMEOUT 300
	#define CONFIG_USB_CABLE_CHECK
	#define CONFIG_THOR_RESET_OFF
	#define DFU_ALT_INFO_RAM \
	"dfu_ram_info=" \
	"setenv dfu_alt_info " \
	"Image ram $kernel_addr $kernel_size\\\\;" \
	"system.dtb ram $fdt_addr $fdt_size\0" \
	"dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \
	"thor_ram=run dfu_ram_info && thordown 0 ram 0\0"

	#define DFU_ALT_INFO \
	DFU_ALT_INFO_RAM

	#ifndef CONFIG_SPL_BUILD
	# define PARTS_DEFAULT \
	"partitions=uuid_disk=${uuid_gpt_disk};" \
	"name=""boot"",size=16M,uuid=${uuid_gpt_boot};" \
	"name=""Linux"",size=-M,uuid=${uuid_gpt_Linux}\0"
	#endif
	#endif

	#if !defined(DFU_ALT_INFO)
	# define DFU_ALT_INFO
	#endif

	#if !defined(PARTS_DEFAULT)
	# define PARTS_DEFAULT
	#endif

	/* Monitor Command Prompt */
	/* Console I/O Buffer Size */
	#define CONFIG_SYS_CBSIZE 2048
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
	#define CONFIG_PANIC_HANG
	#define CONFIG_SYS_MAXARGS 64

	/* Ethernet driver */
	#if defined(CONFIG_ZYNQ_GEM)
	# define CONFIG_MII
	# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
	# define PHY_ANEG_TIMEOUT 20000
	#endif

	/* I2C */
	#if defined(CONFIG_SYS_I2C_ZYNQ)
	# define CONFIG_SYS_I2C
	#endif

	/* EEPROM */
	#ifdef CONFIG_ZYNQMP_EEPROM
	# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
	# define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
	# define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
	# define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
	# define CONFIG_SYS_EEPROM_SIZE (64 * 1024)
	#endif

	#ifdef CONFIG_SATA_CEVA
	#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
	#define CONFIG_SYS_SCSI_MAX_LUN 1
	#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
	CONFIG_SYS_SCSI_MAX_LUN)
	#endif

	#define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024)

	#define CONFIG_CLOCKS

	#define ENV_MEM_LAYOUT_SETTINGS \
	"fdt_high=10000000\0" \
	"initrd_high=10000000\0" \
	"fdt_addr_r=0x40000000\0" \
	"pxefile_addr_r=0x10000000\0" \
	"kernel_addr_r=0x18000000\0" \
	"scriptaddr=0x02000000\0" \
	"ramdisk_addr_r=0x02100000\0" \

	#if defined(CONFIG_MMC_SDHCI_ZYNQ)
	# define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0) func(MMC, mmc, 1)
	#else
	# define BOOT_TARGET_DEVICES_MMC(func)
	#endif

	#if defined(CONFIG_SATA_CEVA)
	# define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
	#else
	# define BOOT_TARGET_DEVICES_SCSI(func)
	#endif

	#if defined(CONFIG_ZYNQMP_USB)
	# define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0) func(USB, usb, 1)
	#else
	# define BOOT_TARGET_DEVICES_USB(func)
	#endif

	#if defined(CONFIG_CMD_PXE) && defined(CONFIG_CMD_DHCP)
	# define BOOT_TARGET_DEVICES_PXE(func) func(PXE, pxe, na)
	#else
	# define BOOT_TARGET_DEVICES_PXE(func)
	#endif

	#if defined(CONFIG_CMD_DHCP)
	# define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na)
	#else
	# define BOOT_TARGET_DEVICES_DHCP(func)
	#endif

	#define BOOT_TARGET_DEVICES(func) \
	BOOT_TARGET_DEVICES_MMC(func) \
	BOOT_TARGET_DEVICES_USB(func) \
	BOOT_TARGET_DEVICES_SCSI(func) \
	BOOT_TARGET_DEVICES_PXE(func) \
	BOOT_TARGET_DEVICES_DHCP(func)

	#include <config_distro_bootcmd.h>

	/* Initial environment variables */
	#ifndef CONFIG_EXTRA_ENV_SETTINGS
	#define CONFIG_EXTRA_ENV_SETTINGS \
	ENV_MEM_LAYOUT_SETTINGS \
	BOOTENV \
	DFU_ALT_INFO
	#endif

	/* SPL can't handle all huge variables - define just DFU */
	#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_DFU_SUPPORT)
	#undef CONFIG_EXTRA_ENV_SETTINGS
	# define CONFIG_EXTRA_ENV_SETTINGS \
	"dfu_alt_info_ram=uboot.bin ram 0x8000000 0x1000000;" \
	"atf-uboot.ub ram 0x10000000 0x1000000;" \
	"Image ram 0x80000 0x3f80000;" \
	"system.dtb ram 0x4000000 0x100000\0" \
	"dfu_bufsiz=0x1000\0"
	#endif

	#define CONFIG_SPL_TEXT_BASE 0xfffc0000
	#define CONFIG_SPL_STACK 0xfffffffc
	#define CONFIG_SPL_MAX_SIZE 0x40000

	/* Just random location in OCM */
	#define CONFIG_SPL_BSS_START_ADDR 0x0
	#define CONFIG_SPL_BSS_MAX_SIZE 0x80000

	#if defined(CONFIG_SPL_SPI_FLASH_SUPPORT)
	# define CONFIG_SYS_SPI_KERNEL_OFFS 0x80000
	# define CONFIG_SYS_SPI_ARGS_OFFS 0xa0000
	# define CONFIG_SYS_SPI_ARGS_SIZE 0xa0000

	# define CONFIG_SYS_SPI_U_BOOT_OFFS 0x170000
	#endif

	/* u-boot is like dtb */
	#define CONFIG_SPL_FS_LOAD_ARGS_NAME "u-boot.bin"
	#define CONFIG_SYS_SPL_ARGS_ADDR 0x8000000

	/* ATF is my kernel image */
	#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "atf-uboot.ub"

	/* FIT load address for RAM boot */
	#define CONFIG_SPL_LOAD_FIT_ADDRESS 0x10000000

	/* MMC support */
	#ifdef CONFIG_MMC_SDHCI_ZYNQ
	# define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
	# define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0 /* unused */
	# define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0 /* unused */
	# define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0 /* unused */
	# define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
	#endif

	#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_DFU_SUPPORT)
	# undef CONFIG_CMD_BOOTD
	# define CONFIG_SPL_ENV_SUPPORT
	# define CONFIG_SPL_HASH_SUPPORT
	# define CONFIG_ENV_MAX_ENTRIES 10
	#endif

	#define CONFIG_SYS_SPL_MALLOC_START 0x20000000
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000

	#ifdef CONFIG_SPL_SYS_MALLOC_SIMPLE
	# error "Disable CONFIG_SPL_SYS_MALLOC_SIMPLE. Full malloc needs to be used"
	#endif

	#define CONFIG_BOARD_EARLY_INIT_F

	#endif /* __XILINX_ZYNQMP_H */