blob: 9ba7258572fcdf25cc112ae2ecc45b814aababd7 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2017, 2019-2021 NXP
* Copyright 2015 Freescale Semiconductor
*/
#ifndef __LS2_QDS_H
#define __LS2_QDS_H
#include "ls2080a_common.h"
#ifdef CONFIG_FSL_QSPI
#define CONFIG_SYS_I2C_IFDR_DIV 0x7e
#endif
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
#define COUNTER_FREQUENCY_REAL (get_board_sys_clk()/4)
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#define SPD_EEPROM_ADDRESS1 0x51
#define SPD_EEPROM_ADDRESS2 0x52
#define SPD_EEPROM_ADDRESS3 0x53
#define SPD_EEPROM_ADDRESS4 0x54
#define SPD_EEPROM_ADDRESS5 0x55
#define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */
#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
#define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024)
#define CONFIG_SYS_NOR0_CSPR \
(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
CSPR_PORT_SIZE_16 | \
CSPR_MSEL_NOR | \
CSPR_V)
#define CONFIG_SYS_NOR0_CSPR_EARLY \
(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \
CSPR_PORT_SIZE_16 | \
CSPR_MSEL_NOR | \
CSPR_V)
#define CONFIG_SYS_NOR1_CSPR \
(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS) | \
CSPR_PORT_SIZE_16 | \
CSPR_MSEL_NOR | \
CSPR_V)
#define CONFIG_SYS_NOR1_CSPR_EARLY \
(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS_EARLY) | \
CSPR_PORT_SIZE_16 | \
CSPR_MSEL_NOR | \
CSPR_V)
#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12)
#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
FTIM0_NOR_TEADC(0x5) | \
FTIM0_NOR_TEAHC(0x5))
#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
FTIM1_NOR_TRAD_NOR(0x1a) |\
FTIM1_NOR_TSEQRAD_NOR(0x13))
#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
FTIM2_NOR_TCH(0x4) | \
FTIM2_NOR_TWPH(0x0E) | \
FTIM2_NOR_TWP(0x1c))
#define CONFIG_SYS_NOR_FTIM3 0x04000000
#define CONFIG_SYS_IFC_CCR 0x01000000
#ifdef CONFIG_MTD_NOR_FLASH
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\
CONFIG_SYS_FLASH_BASE + 0x40000000}
#endif
#define CONFIG_SYS_NAND_MAX_ECCPOS 256
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
| CSPR_MSEL_NAND /* MSEL = NAND */ \
| CSPR_V)
#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
| CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
| CSOR_NAND_PGS_2K /* Page Size = 2K */ \
| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
FTIM0_NAND_TWP(0x18) | \
FTIM0_NAND_TWCHT(0x07) | \
FTIM0_NAND_TWH(0x0a))
#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
FTIM1_NAND_TWBE(0x39) | \
FTIM1_NAND_TRR(0x0e) | \
FTIM1_NAND_TRP(0x18))
#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
FTIM2_NAND_TREH(0x0a) | \
FTIM2_NAND_TWHRE(0x1e))
#define CONFIG_SYS_NAND_FTIM3 0x0
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
#define QIXIS_LBMAP_SWITCH 0x06
#define QIXIS_LBMAP_MASK 0x0f
#define QIXIS_LBMAP_SHIFT 0
#define QIXIS_LBMAP_DFLTBANK 0x00
#define QIXIS_LBMAP_ALTBANK 0x04
#define QIXIS_LBMAP_NAND 0x09
#define QIXIS_LBMAP_SD 0x00
#define QIXIS_LBMAP_QSPI 0x0f
#define QIXIS_RST_CTL_RESET 0x31
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
#define QIXIS_RCW_SRC_NAND 0x107
#define QIXIS_RCW_SRC_SD 0x40
#define QIXIS_RCW_SRC_QSPI 0x62
#define QIXIS_RST_FORCE_MEM 0x01
#define CONFIG_SYS_CSPR3_EXT (0x0)
#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
| CSPR_PORT_SIZE_8 \
| CSPR_MSEL_GPCM \
| CSPR_V)
#define CONFIG_SYS_CSPR3_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
| CSPR_PORT_SIZE_8 \
| CSPR_MSEL_GPCM \
| CSPR_V)
#define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024)
#define CONFIG_SYS_CSOR3 CSOR_GPCM_ADM_SHIFT(12)
/* QIXIS Timing parameters for IFC CS3 */
#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
FTIM0_GPCM_TEADC(0x0e) | \
FTIM0_GPCM_TEAHC(0x0e))
#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
FTIM1_GPCM_TRAD(0x3f))
#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0xf) | \
FTIM2_GPCM_TCH(0xf) | \
FTIM2_GPCM_TWP(0x3E))
#define CONFIG_SYS_CS3_FTIM3 0x0
#if defined(CONFIG_SPL)
#if defined(CONFIG_NAND_BOOT)
#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR_EARLY
#define CONFIG_SYS_CSPR1_FINAL CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR_EARLY
#define CONFIG_SYS_CSPR2_FINAL CONFIG_SYS_NOR1_CSPR
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK_EARLY
#define CONFIG_SYS_AMASK2_FINAL CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
#define CONFIG_SYS_NAND_U_BOOT_SIZE (640 * 1024)
#endif
#else
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR_EARLY
#define CONFIG_SYS_CSPR1_FINAL CONFIG_SYS_NOR1_CSPR
#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK_EARLY
#define CONFIG_SYS_AMASK1_FINAL CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
#endif
/* Debug Server firmware */
#define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
#define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL
#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
/*
* I2C
*/
#define I2C_MUX_PCA_ADDR 0x77
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/
/* I2C bus multiplexer */
#define I2C_MUX_CH_DEFAULT 0x8
/* SPI */
/*
* Verify QSPI when boot from NAND, QIXIS brdcfg9 need configure.
* If boot from on-board NAND, ISO1 = 1, ISO2 = 0, IBOOT = 0
* If boot from IFCCard NAND, ISO1 = 0, ISO2 = 0, IBOOT = 1
*/
#define FSL_QIXIS_BRDCFG9_QSPI 0x1
/*
* RTC configuration
*/
#define RTC
#define CONFIG_RTC_DS3231 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
/* EEPROM */
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
#define CONFIG_FSL_MEMAC
/* Initial environment variables */
#undef CONFIG_EXTRA_ENV_SETTINGS
#ifdef CONFIG_NXP_ESBC
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"loadaddr=0x80100000\0" \
"kernel_addr=0x100000\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x581000000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"mcmemsize=0x40000000\0" \
"mcinitcmd=esbc_validate 0x580640000;" \
"esbc_validate 0x580680000;" \
"fsl_mc start mc 0x580a00000" \
" 0x580e00000 \0"
#else
#ifdef CONFIG_TFABOOT
#define SD_MC_INIT_CMD \
"mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
"mmc read 0x80e00000 0x7000 0x800;" \
"fsl_mc start mc 0x80a00000 0x80e00000\0"
#define IFC_MC_INIT_CMD \
"fsl_mc start mc 0x580a00000" \
" 0x580e00000 \0"
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"loadaddr=0x80100000\0" \
"loadaddr_sd=0x90100000\0" \
"kernel_addr=0x581000000\0" \
"kernel_addr_sd=0x8000\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x581000000\0" \
"kernel_start_sd=0x8000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"kernel_size_sd=0x14000\0" \
"load_addr=0xa0000000\0" \
"kernelheader_addr=0x580600000\0" \
"kernelheader_addr_r=0x80200000\0" \
"kernelheader_size=0x40000\0" \
"BOARD=ls2088aqds\0" \
"mcmemsize=0x70000000 \0" \
"scriptaddr=0x80000000\0" \
"scripthdraddr=0x80080000\0" \
IFC_MC_INIT_CMD \
BOOTENV \
"boot_scripts=ls2088aqds_boot.scr\0" \
"boot_script_hdr=hdr_ls2088aqds_bs.out\0" \
"scan_dev_for_boot_part=" \
"part list ${devtype} ${devnum} devplist; " \
"env exists devplist || setenv devplist 1; " \
"for distro_bootpart in ${devplist}; do " \
"if fstype ${devtype} " \
"${devnum}:${distro_bootpart} " \
"bootfstype; then " \
"run scan_dev_for_boot; " \
"fi; " \
"done\0" \
"boot_a_script=" \
"load ${devtype} ${devnum}:${distro_bootpart} " \
"${scriptaddr} ${prefix}${script}; " \
"env exists secureboot && load ${devtype} " \
"${devnum}:${distro_bootpart} " \
"${scripthdraddr} ${prefix}${boot_script_hdr} " \
"&& esbc_validate ${scripthdraddr};" \
"source ${scriptaddr}\0" \
"nor_bootcmd=echo Trying load from nor..;" \
"cp.b $kernel_addr $load_addr " \
"$kernel_size ; env exists secureboot && " \
"cp.b $kernelheader_addr $kernelheader_addr_r " \
"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
"bootm $load_addr#$BOARD\0" \
"sd_bootcmd=echo Trying load from SD ..;" \
"mmcinfo; mmc read $load_addr " \
"$kernel_addr_sd $kernel_size_sd && " \
"bootm $load_addr#$BOARD\0"
#elif defined(CONFIG_SD_BOOT)
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"loadaddr=0x90100000\0" \
"kernel_addr=0x800\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x8000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x14000\0" \
"mcinitcmd=mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
"mmc read 0x80e00000 0x7000 0x800;" \
"fsl_mc start mc 0x80a00000 0x80e00000\0" \
"mcmemsize=0x70000000 \0"
#else
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"loadaddr=0x80100000\0" \
"kernel_addr=0x100000\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x581000000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"mcmemsize=0x40000000\0" \
"mcinitcmd=fsl_mc start mc 0x580a00000" \
" 0x580e00000 \0"
#endif /* CONFIG_TFABOOT */
#endif /* CONFIG_NXP_ESBC */
#ifdef CONFIG_TFABOOT
#define BOOT_TARGET_DEVICES(func) \
func(USB, usb, 0) \
func(MMC, mmc, 0) \
func(SCSI, scsi, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#define SD_BOOTCOMMAND \
"env exists mcinitcmd && env exists secureboot "\
"&& mmcinfo && mmc read $load_addr 0x3600 0x800 " \
"&& esbc_validate $load_addr; " \
"env exists mcinitcmd && run mcinitcmd " \
"&& mmc read 0x80d00000 0x6800 0x800 " \
"&& fsl_mc lazyapply dpl 0x80d00000; " \
"run distro_bootcmd;run sd_bootcmd; " \
"env exists secureboot && esbc_halt;"
#define IFC_NOR_BOOTCOMMAND \
"env exists mcinitcmd && env exists secureboot "\
"&& esbc_validate 0x5806C0000; env exists mcinitcmd "\
"&& fsl_mc lazyapply dpl 0x580d00000;" \
"run distro_bootcmd;run nor_bootcmd; " \
"env exists secureboot && esbc_halt;"
#endif
#if defined(CONFIG_FSL_MC_ENET)
#define CONFIG_FSL_MEMAC
#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
#define SGMII_CARD_PORT2_PHY_ADDR 0x1d
#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
#define XQSGMII_CARD_PHY1_PORT0_ADDR 0x0
#define XQSGMII_CARD_PHY1_PORT1_ADDR 0x1
#define XQSGMII_CARD_PHY1_PORT2_ADDR 0x2
#define XQSGMII_CARD_PHY1_PORT3_ADDR 0x3
#define XQSGMII_CARD_PHY2_PORT0_ADDR 0x4
#define XQSGMII_CARD_PHY2_PORT1_ADDR 0x5
#define XQSGMII_CARD_PHY2_PORT2_ADDR 0x6
#define XQSGMII_CARD_PHY2_PORT3_ADDR 0x7
#define XQSGMII_CARD_PHY3_PORT0_ADDR 0x8
#define XQSGMII_CARD_PHY3_PORT1_ADDR 0x9
#define XQSGMII_CARD_PHY3_PORT2_ADDR 0xa
#define XQSGMII_CARD_PHY3_PORT3_ADDR 0xb
#define XQSGMII_CARD_PHY4_PORT0_ADDR 0xc
#define XQSGMII_CARD_PHY4_PORT1_ADDR 0xd
#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
#endif
#include <asm/fsl_secure_boot.h>
#endif /* __LS2_QDS_H */