| // SPDX-License-Identifier: GPL-2.0+ OR X11 |
| /* |
| * NXP ls1028a SOC common device tree source |
| * |
| * Copyright 2019-2020 NXP |
| * |
| */ |
| |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| |
| / { |
| compatible = "fsl,ls1028a"; |
| interrupt-parent = <&gic>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| sysclk: sysclk { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <100000000>; |
| clock-output-names = "sysclk"; |
| }; |
| |
| gic: interrupt-controller@6000000 { |
| compatible = "arm,gic-v3"; |
| reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */ |
| <0x0 0x06040000 0 0x40000>; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0xf) | |
| IRQ_TYPE_LEVEL_LOW)>; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | |
| IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | |
| IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | |
| IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | |
| IRQ_TYPE_LEVEL_LOW)>; |
| }; |
| |
| soc: soc { |
| compatible = "simple-bus"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| clockgen: clocking@1300000 { |
| compatible = "fsl,ls1028a-clockgen"; |
| reg = <0x0 0x1300000 0x0 0xa0000>; |
| #clock-cells = <2>; |
| clocks = <&sysclk>; |
| }; |
| |
| i2c0: i2c@2000000 { |
| compatible = "fsl,vf610-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x2000000 0x0 0x10000>; |
| interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "i2c"; |
| clocks = <&clockgen 4 0>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@2010000 { |
| compatible = "fsl,vf610-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x2010000 0x0 0x10000>; |
| interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "i2c"; |
| clocks = <&clockgen 4 0>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@2020000 { |
| compatible = "fsl,vf610-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x2020000 0x0 0x10000>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "i2c"; |
| clocks = <&clockgen 4 0>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@2030000 { |
| compatible = "fsl,vf610-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x2030000 0x0 0x10000>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "i2c"; |
| clocks = <&clockgen 4 0>; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@2040000 { |
| compatible = "fsl,vf610-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x2040000 0x0 0x10000>; |
| interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "i2c"; |
| clocks = <&clockgen 4 0>; |
| status = "disabled"; |
| }; |
| |
| i2c5: i2c@2050000 { |
| compatible = "fsl,vf610-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x2050000 0x0 0x10000>; |
| interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "i2c"; |
| clocks = <&clockgen 4 0>; |
| status = "disabled"; |
| }; |
| |
| i2c6: i2c@2060000 { |
| compatible = "fsl,vf610-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x2060000 0x0 0x10000>; |
| interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "i2c"; |
| clocks = <&clockgen 4 0>; |
| status = "disabled"; |
| }; |
| |
| i2c7: i2c@2070000 { |
| compatible = "fsl,vf610-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x2070000 0x0 0x10000>; |
| interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "i2c"; |
| clocks = <&clockgen 4 0>; |
| status = "disabled"; |
| }; |
| |
| fspi: flexspi@20c0000 { |
| compatible = "nxp,lx2160a-fspi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x20c0000 0x0 0x10000>, |
| <0x0 0x20000000 0x0 0x10000000>; |
| reg-names = "fspi_base", "fspi_mmap"; |
| clocks = <&clockgen 4 3>, <&clockgen 4 3>; |
| clock-names = "fspi_en", "fspi"; |
| interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| dspi0: dspi@2100000 { |
| compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x2100000 0x0 0x10000>; |
| interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "dspi"; |
| clocks = <&clockgen 4 0>; |
| spi-num-chipselects = <5>; |
| litte-endian; |
| status = "disabled"; |
| }; |
| |
| dspi1: dspi@2110000 { |
| compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x2110000 0x0 0x10000>; |
| interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "dspi"; |
| clocks = <&clockgen 4 0>; |
| spi-num-chipselects = <5>; |
| little-endian; |
| status = "disabled"; |
| }; |
| |
| dspi2: dspi@2120000 { |
| compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x2120000 0x0 0x10000>; |
| interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "dspi"; |
| clocks = <&clockgen 4 0>; |
| spi-num-chipselects = <5>; |
| little-endian; |
| status = "disabled"; |
| }; |
| |
| esdhc: esdhc@2140000 { |
| compatible = "fsl,esdhc"; |
| reg = <0x0 0x2140000 0x0 0x10000>; |
| interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; |
| big-endian; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| esdhc1: esdhc@2150000 { |
| compatible = "fsl,esdhc"; |
| reg = <0x0 0x2150000 0x0 0x10000>; |
| interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; |
| big-endian; |
| non-removable; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| duart0: serial@21c0500 { |
| device_type = "serial"; |
| compatible = "fsl,ns16550", "ns16550a"; |
| reg = <0x0 0x21c0500 0x0 0x100>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| duart1: serial@21c0600 { |
| device_type = "serial"; |
| compatible = "fsl,ns16550", "ns16550a"; |
| reg = <0x0 0x21c0600 0x0 0x100>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| lpuart0: serial@2260000 { |
| compatible = "fsl,ls1028a-lpuart"; |
| reg = <0x0 0x2260000 0x0 0x1000>; |
| interrupts = <0 232 0x4>; |
| clocks = <&sysclk>; |
| clock-names = "ipg"; |
| status = "disabled"; |
| }; |
| |
| lpuart1: serial@2270000 { |
| compatible = "fsl,ls1028a-lpuart"; |
| reg = <0x0 0x2270000 0x0 0x1000>; |
| interrupts = <0 233 0x4>; |
| clocks = <&sysclk>; |
| clock-names = "ipg"; |
| status = "disabled"; |
| }; |
| |
| lpuart2: serial@2280000 { |
| compatible = "fsl,ls1028a-lpuart"; |
| reg = <0x0 0x2280000 0x0 0x1000>; |
| interrupts = <0 234 0x4>; |
| clocks = <&sysclk>; |
| clock-names = "ipg"; |
| status = "disabled"; |
| }; |
| |
| lpuart3: serial@2290000 { |
| compatible = "fsl,ls1028a-lpuart"; |
| reg = <0x0 0x2290000 0x0 0x1000>; |
| interrupts = <0 235 0x4>; |
| clocks = <&sysclk>; |
| clock-names = "ipg"; |
| status = "disabled"; |
| }; |
| |
| lpuart4: serial@22a0000 { |
| compatible = "fsl,ls1028a-lpuart"; |
| reg = <0x0 0x22a0000 0x0 0x1000>; |
| interrupts = <0 236 0x4>; |
| clocks = <&sysclk>; |
| clock-names = "ipg"; |
| status = "disabled"; |
| }; |
| |
| lpuart5: serial@22b0000 { |
| compatible = "fsl,ls1028a-lpuart"; |
| reg = <0x0 0x22b0000 0x0 0x1000>; |
| interrupts = <0 237 0x4>; |
| clocks = <&sysclk>; |
| clock-names = "ipg"; |
| status = "disabled"; |
| }; |
| |
| gpio1: gpio@2300000 { |
| compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; |
| reg = <0x0 0x2300000 0x0 0x10000>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| little-endian; |
| }; |
| |
| gpio2: gpio@2310000 { |
| compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; |
| reg = <0x0 0x2310000 0x0 0x10000>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| little-endian; |
| }; |
| |
| gpio3: gpio@2320000 { |
| compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; |
| reg = <0x0 0x2320000 0x0 0x10000>; |
| interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| little-endian; |
| }; |
| |
| usb0: usb3@3100000 { |
| compatible = "fsl,ls1028a-dwc3", "snps,dwc3"; |
| reg = <0x0 0x3100000 0x0 0x10000>; |
| interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; |
| dr_mode = "host"; |
| status = "disabled"; |
| }; |
| |
| usb1: usb3@3110000 { |
| compatible = "fsl,ls1028a-dwc3", "snps,dwc3"; |
| reg = <0x0 0x3110000 0x0 0x10000>; |
| interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; |
| dr_mode = "host"; |
| status = "disabled"; |
| }; |
| |
| sata: sata@3200000 { |
| compatible = "fsl,ls1028a-ahci"; |
| reg = <0x0 0x3200000 0x0 0x10000 /* ccsr sata base */ |
| 0x7 0x100520 0x0 0x4>; /* ecc sata addr*/ |
| reg-names = "ahci", "sata-ecc"; |
| interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| pcie1: pcie@3400000 { |
| compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie"; |
| reg = <0x00 0x03400000 0x0 0x80000 |
| 0x00 0x03480000 0x0 0x40000 /* lut registers */ |
| 0x00 0x034c0000 0x0 0x40000 /* pf controls registers */ |
| 0x80 0x00000000 0x0 0x20000>; /* configuration space */ |
| reg-names = "dbi", "lut", "ctrl", "config"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| num-lanes = <4>; |
| bus-range = <0x0 0xff>; |
| ranges = <0x81000000 0x0 0x00000000 0x80 0x00020000 0x0 0x00010000 /* downstream I/O */ |
| 0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ |
| }; |
| |
| pcie2: pcie@3500000 { |
| compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie"; |
| reg = <0x00 0x03500000 0x0 0x80000 |
| 0x00 0x03580000 0x0 0x40000 /* lut registers */ |
| 0x00 0x035c0000 0x0 0x40000 /* pf controls registers */ |
| 0x88 0x00000000 0x0 0x20000>; /* configuration space */ |
| reg-names = "dbi", "lut", "ctrl", "config"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| num-lanes = <4>; |
| bus-range = <0x0 0xff>; |
| ranges = <0x81000000 0x0 0x00000000 0x88 0x00020000 0x0 0x00010000 /* downstream I/O */ |
| 0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ |
| }; |
| |
| cluster1_core0_watchdog: wdt@c000000 { |
| compatible = "arm,sp805", "arm,primecell"; |
| reg = <0x0 0xc000000 0x0 0x1000>; |
| }; |
| |
| pcie@1f0000000 { |
| compatible = "pci-host-ecam-generic"; |
| /* ECAM bus 0, HW has more space reserved but not populated */ |
| bus-range = <0x0 0x0>; |
| reg = <0x01 0xf0000000 0x0 0x100000>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| ranges = <0x82000000 0x0 0x00000000 0x1 0xf8000000 0x0 0x160000>; |
| |
| enetc_port0: pci@0,0 { |
| reg = <0x000000 0 0 0 0>; |
| status = "disabled"; |
| }; |
| |
| enetc_port1: pci@0,1 { |
| reg = <0x000100 0 0 0 0>; |
| status = "disabled"; |
| }; |
| |
| enetc_port2: pci@0,2 { |
| reg = <0x000200 0 0 0 0>; |
| status = "disabled"; |
| phy-mode = "internal"; |
| |
| fixed-link { |
| speed = <2500>; |
| full-duplex; |
| }; |
| }; |
| |
| enetc_mdio_pf3: pci@0,3 { |
| #address-cells=<0>; |
| #size-cells=<1>; |
| reg = <0x000300 0 0 0 0>; |
| status = "disabled"; |
| |
| fixed-link { |
| speed = <1000>; |
| full-duplex; |
| }; |
| }; |
| |
| mscc_felix: pci@0,5 { |
| reg = <0x000500 0 0 0 0>; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| mscc_felix_port0: port@0 { |
| reg = <0>; |
| status = "disabled"; |
| }; |
| |
| mscc_felix_port1: port@1 { |
| reg = <1>; |
| status = "disabled"; |
| }; |
| |
| mscc_felix_port2: port@2 { |
| reg = <2>; |
| status = "disabled"; |
| }; |
| |
| mscc_felix_port3: port@3 { |
| reg = <3>; |
| status = "disabled"; |
| }; |
| |
| mscc_felix_port4: port@4 { |
| reg = <4>; |
| phy-mode = "internal"; |
| status = "disabled"; |
| |
| fixed-link { |
| speed = <2500>; |
| full-duplex; |
| }; |
| }; |
| |
| mscc_felix_port5: port@5 { |
| reg = <5>; |
| phy-mode = "internal"; |
| status = "disabled"; |
| |
| fixed-link { |
| speed = <1000>; |
| full-duplex; |
| }; |
| |
| }; |
| }; |
| }; |
| |
| enetc_port3: pci@0,6 { |
| reg = <0x000600 0 0 0 0>; |
| status = "disabled"; |
| phy-mode = "internal"; |
| }; |
| }; |
| }; |
| }; |