include/configs/uniphier.h - platform/external/u-boot - Gitiles

 /*
  * Copyright (C) 2012-2015 Panasonic Corporation
  *   Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 /* U-boot - Common settings for UniPhier Family */

 #ifndef __CONFIG_UNIPHIER_COMMON_H__
 #define __CONFIG_UNIPHIER_COMMON_H__

 #if defined(CONFIG_MACH_PH1_PRO4)
 #define CONFIG_DDR_NUM_CH0 2
 #define CONFIG_DDR_NUM_CH1 2

 /* Physical start address of SDRAM */
 #define CONFIG_SDRAM0_BASE	0x80000000
 #define CONFIG_SDRAM0_SIZE	0x20000000
 #define CONFIG_SDRAM1_BASE	0xa0000000
 #define CONFIG_SDRAM1_SIZE	0x20000000
 #endif

 #if defined(CONFIG_MACH_PH1_LD4)
 #define CONFIG_DDR_NUM_CH0 1
 #define CONFIG_DDR_NUM_CH1 1

 /* Physical start address of SDRAM */
 #define CONFIG_SDRAM0_BASE	0x80000000
 #define CONFIG_SDRAM0_SIZE	0x10000000
 #define CONFIG_SDRAM1_BASE	0x90000000
 #define CONFIG_SDRAM1_SIZE	0x10000000
 #endif

 #if defined(CONFIG_MACH_PH1_SLD8)
 #define CONFIG_DDR_NUM_CH0 1
 #define CONFIG_DDR_NUM_CH1 1

 /* Physical start address of SDRAM */
 #define CONFIG_SDRAM0_BASE	0x80000000
 #define CONFIG_SDRAM0_SIZE	0x10000000
 #define CONFIG_SDRAM1_BASE	0x90000000
 #define CONFIG_SDRAM1_SIZE	0x10000000
 #endif

 #define CONFIG_I2C_EEPROM
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  10

 /*
  * Support card address map
  */
 #if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
 # define CONFIG_SUPPORT_CARD_BASE	0x03f00000
 # define CONFIG_SUPPORT_CARD_ETHER_BASE	(CONFIG_SUPPORT_CARD_BASE + 0x00000000)
 # define CONFIG_SUPPORT_CARD_LED_BASE	(CONFIG_SUPPORT_CARD_BASE + 0x00090000)
 # define CONFIG_SUPPORT_CARD_UART_BASE	(CONFIG_SUPPORT_CARD_BASE + 0x000b0000)
 #endif

 #if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
 # define CONFIG_SUPPORT_CARD_BASE	0x08000000
 # define CONFIG_SUPPORT_CARD_ETHER_BASE	(CONFIG_SUPPORT_CARD_BASE + 0x00000000)
 # define CONFIG_SUPPORT_CARD_LED_BASE	(CONFIG_SUPPORT_CARD_BASE + 0x00401630)
 # define CONFIG_SUPPORT_CARD_UART_BASE	(CONFIG_SUPPORT_CARD_BASE + 0x00200000)
 #endif

 #ifdef CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_COM1		CONFIG_SUPPORT_CARD_UART_BASE
 #define CONFIG_SYS_NS16550_CLK		12288000
 #define CONFIG_SYS_NS16550_REG_SIZE	-2
 #endif

 /* TODO: move to Kconfig and device tree */
 #if 0
 #define CONFIG_SYS_NS16550_SERIAL
 #endif

 #define CONFIG_SMC911X

 #define CONFIG_SMC911X_BASE		CONFIG_SUPPORT_CARD_ETHER_BASE
 #define CONFIG_SMC911X_32_BIT

 /*-----------------------------------------------------------------------
  * MMU and Cache Setting
  *----------------------------------------------------------------------*/

 /* Comment out the following to enable L1 cache */
 /* #define CONFIG_SYS_ICACHE_OFF */
 /* #define CONFIG_SYS_DCACHE_OFF */

 #define CONFIG_SYS_CACHELINE_SIZE	32

 /* Comment out the following to enable L2 cache */
 #define CONFIG_UNIPHIER_L2CACHE_ON

 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO
 #define CONFIG_MISC_INIT_F
 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_EARLY_INIT_R
 #define CONFIG_BOARD_LATE_INIT

 #define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)

 #define CONFIG_TIMESTAMP

 /* FLASH related */
 #define CONFIG_MTD_DEVICE

 /*
  * uncomment the following to disable FLASH related code.
  */
 /* #define CONFIG_SYS_NO_FLASH */

 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI

 #define CONFIG_SYS_MAX_FLASH_SECT	256
 #define CONFIG_SYS_MONITOR_BASE		0
 #define CONFIG_SYS_FLASH_BASE		0

 /*
  * flash_toggle does not work for out supoort card.
  * We need to use flash_status_poll.
  */
 #define CONFIG_SYS_CFI_FLASH_STATUS_POLL

 #define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */

 #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2

 /* serial console configuration */
 #define CONFIG_BAUDRATE			115200

 #define CONFIG_SYS_GENERIC_BOARD

 #if !defined(CONFIG_SPL_BUILD)
 #define CONFIG_USE_ARCH_MEMSET
 #define CONFIG_USE_ARCH_MEMCPY
 #endif

 #define CONFIG_SYS_LONGHELP		/* undef to save memory */

 #define CONFIG_CMDLINE_EDITING		/* add command line history	*/
 #define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size */
 /* Print Buffer Size */
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS		16	/* max number of command */
 /* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)

 #define CONFIG_CONS_INDEX		1

 /*
  * For NAND booting the environment is embedded in the U-Boot image. Please take
  * look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
  */
 /* #define CONFIG_ENV_IS_IN_NAND */
 #define CONFIG_ENV_IS_NOWHERE
 #define CONFIG_ENV_SIZE				0x2000
 #define CONFIG_ENV_OFFSET			0x0
 /* #define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */

 /* Time clock 1MHz */
 #define CONFIG_SYS_TIMER_RATE			1000000

 /*
  * By default, ARP timeout is 5 sec.
  * The first ARP request does not seem to work.
  * So we need to retry ARP request anyway.
  * We want to shrink the interval until the second ARP request.
  */
 #define CONFIG_ARP_TIMEOUT	500UL  /* 0.5 msec */

 #define CONFIG_SYS_MAX_NAND_DEVICE			1
 #define CONFIG_SYS_NAND_MAX_CHIPS			2
 #define CONFIG_SYS_NAND_ONFI_DETECTION

 #define CONFIG_NAND_DENALI_ECC_SIZE			1024

 #define CONFIG_SYS_NAND_REGS_BASE			0x68100000
 #define CONFIG_SYS_NAND_DATA_BASE			0x68000000

 #define CONFIG_SYS_NAND_BASE		(CONFIG_SYS_NAND_DATA_BASE + 0x10)

 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 #define CONFIG_SYS_NAND_BAD_BLOCK_POS			0

 /* USB */
 #define CONFIG_USB_MAX_CONTROLLER_COUNT		2
 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS	4
 #define CONFIG_CMD_FAT
 #define CONFIG_FAT_WRITE
 #define CONFIG_DOS_PARTITION

 /* memtest works on */
 #define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x01000000)

 #define CONFIG_BOOTDELAY			3
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 #define CONFIG_AUTOBOOT_KEYED			1
 #define CONFIG_AUTOBOOT_PROMPT	\
 	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
 #define CONFIG_AUTOBOOT_DELAY_STR		"d"
 #define CONFIG_AUTOBOOT_STOP_STR		" "

 /*
  * Network Configuration
  */
 #define CONFIG_ETHADDR			00:21:83:24:00:00
 #define CONFIG_SERVERIP			192.168.11.1
 #define CONFIG_IPADDR			192.168.11.10
 #define CONFIG_GATEWAYIP		192.168.11.1
 #define CONFIG_NETMASK			255.255.255.0

 #define CONFIG_LOADADDR			0x84000000
 #define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
 #define CONFIG_BOOTFILE			"fit.itb"

 #define CONFIG_CMDLINE_EDITING		/* add command line history	*/

 #define CONFIG_BOOTCOMMAND		"run $bootmode"

 #define CONFIG_ROOTPATH			"/nfs/root/path"
 #define CONFIG_NFSBOOTCOMMAND						\
 	"setenv bootargs $bootargs root=/dev/nfs rw "			\
 	"nfsroot=$serverip:$rootpath "					\
 	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \
 	"tftpboot; bootm;"

 #define CONFIG_BOOTARGS		" user_debug=0x1f init=/sbin/init"

 #define	CONFIG_EXTRA_ENV_SETTINGS		\
 	"netdev=eth0\0"				\
 	"image_offset=0x00080000\0"		\
 	"image_size=0x00f00000\0"		\
 	"verify=n\0"				\
 	"nandupdate=nand erase 0 0x100000 &&"				\
 		   "tftpboot u-boot-spl.bin &&"				\
 		   "nand write $loadaddr 0 0x10000 &&"			\
 		   "tftpboot u-boot-dtb.img &&"				\
 		   "nand write $loadaddr 0x10000 0xf0000\0"		\
 	"norboot=run add_default_bootargs &&"				\
 		"bootm $image_offset\0"					\
 	"nandboot=run add_default_bootargs &&"				\
 		 "nand read $loadaddr $image_offset $image_size &&"	\
 		 "bootm\0"						\
 	"add_default_bootargs=setenv bootargs $bootargs"		\
 		" console=ttyS0,$baudrate\0"				\

 /* Open Firmware flat tree */
 #define CONFIG_OF_LIBFDT

 #define CONFIG_HAVE_ARM_SECURE

 /* Memory Size & Mapping */
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SDRAM0_BASE

 #if CONFIG_SDRAM0_BASE + CONFIG_SDRAM0_SIZE >= CONFIG_SDRAM1_BASE
 /* Thre is no memory hole */
 #define CONFIG_NR_DRAM_BANKS		1
 #define CONFIG_SYS_SDRAM_SIZE	(CONFIG_SDRAM0_SIZE + CONFIG_SDRAM1_SIZE)
 #else
 #define CONFIG_NR_DRAM_BANKS		2
 #define CONFIG_SYS_SDRAM_SIZE	(CONFIG_SDRAM0_SIZE)
 #endif

 #define CONFIG_SYS_TEXT_BASE		0x84000000

 #if defined(CONFIG_MACH_PH1_LD4) || defined(CONFIG_MACH_PH1_SLD8)
 #define CONFIG_SPL_TEXT_BASE		0x00040000
 #endif
 #if defined(CONFIG_MACH_PH1_PRO4)
 #define CONFIG_SPL_TEXT_BASE		0x00100000
 #endif

 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_SKIP_LOWLEVEL_INIT
 #endif

 #define CONFIG_SYS_SPL_MALLOC_START	(0x0ff00000)
 #define CONFIG_SYS_SPL_MALLOC_SIZE	(0x00004000)

 #ifdef CONFIG_SPL_BUILD
 #define CONFIG_SYS_INIT_SP_ADDR		(0x0ff08000)
 #else
 #define CONFIG_SYS_INIT_SP_ADDR		((CONFIG_SYS_TEXT_BASE) - 0x00001000)
 #endif

 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_NAND_SUPPORT

 #define CONFIG_SPL_LIBCOMMON_SUPPORT	/* for mem_malloc_init */
 #define CONFIG_SPL_LIBGENERIC_SUPPORT

 #define CONFIG_SPL_BOARD_INIT

 #define CONFIG_SYS_NAND_U_BOOT_OFFS		0x10000

 #endif /* __CONFIG_UNIPHIER_COMMON_H__ */
	/*
	* Copyright (C) 2012-2015 Panasonic Corporation
	* Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	/* U-boot - Common settings for UniPhier Family */

	#ifndef __CONFIG_UNIPHIER_COMMON_H__
	#define __CONFIG_UNIPHIER_COMMON_H__

	#if defined(CONFIG_MACH_PH1_PRO4)
	#define CONFIG_DDR_NUM_CH0 2
	#define CONFIG_DDR_NUM_CH1 2

	/* Physical start address of SDRAM */
	#define CONFIG_SDRAM0_BASE 0x80000000
	#define CONFIG_SDRAM0_SIZE 0x20000000
	#define CONFIG_SDRAM1_BASE 0xa0000000
	#define CONFIG_SDRAM1_SIZE 0x20000000
	#endif

	#if defined(CONFIG_MACH_PH1_LD4)
	#define CONFIG_DDR_NUM_CH0 1
	#define CONFIG_DDR_NUM_CH1 1

	/* Physical start address of SDRAM */
	#define CONFIG_SDRAM0_BASE 0x80000000
	#define CONFIG_SDRAM0_SIZE 0x10000000
	#define CONFIG_SDRAM1_BASE 0x90000000
	#define CONFIG_SDRAM1_SIZE 0x10000000
	#endif

	#if defined(CONFIG_MACH_PH1_SLD8)
	#define CONFIG_DDR_NUM_CH0 1
	#define CONFIG_DDR_NUM_CH1 1

	/* Physical start address of SDRAM */
	#define CONFIG_SDRAM0_BASE 0x80000000
	#define CONFIG_SDRAM0_SIZE 0x10000000
	#define CONFIG_SDRAM1_BASE 0x90000000
	#define CONFIG_SDRAM1_SIZE 0x10000000
	#endif

	#define CONFIG_I2C_EEPROM
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10

	/*
	* Support card address map
	*/
	#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
	# define CONFIG_SUPPORT_CARD_BASE 0x03f00000
	# define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
	# define CONFIG_SUPPORT_CARD_LED_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00090000)
	# define CONFIG_SUPPORT_CARD_UART_BASE (CONFIG_SUPPORT_CARD_BASE + 0x000b0000)
	#endif

	#if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
	# define CONFIG_SUPPORT_CARD_BASE 0x08000000
	# define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
	# define CONFIG_SUPPORT_CARD_LED_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00401630)
	# define CONFIG_SUPPORT_CARD_UART_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00200000)
	#endif

	#ifdef CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550
	#define CONFIG_SYS_NS16550_COM1 CONFIG_SUPPORT_CARD_UART_BASE
	#define CONFIG_SYS_NS16550_CLK 12288000
	#define CONFIG_SYS_NS16550_REG_SIZE -2
	#endif

	/* TODO: move to Kconfig and device tree */
	#if 0
	#define CONFIG_SYS_NS16550_SERIAL
	#endif

	#define CONFIG_SMC911X

	#define CONFIG_SMC911X_BASE CONFIG_SUPPORT_CARD_ETHER_BASE
	#define CONFIG_SMC911X_32_BIT

	/*-----------------------------------------------------------------------
	* MMU and Cache Setting
	----------------------------------------------------------------------/

	/* Comment out the following to enable L1 cache */
	/* #define CONFIG_SYS_ICACHE_OFF */
	/* #define CONFIG_SYS_DCACHE_OFF */

	#define CONFIG_SYS_CACHELINE_SIZE 32

	/* Comment out the following to enable L2 cache */
	#define CONFIG_UNIPHIER_L2CACHE_ON

	#define CONFIG_DISPLAY_CPUINFO
	#define CONFIG_DISPLAY_BOARDINFO
	#define CONFIG_MISC_INIT_F
	#define CONFIG_BOARD_EARLY_INIT_F
	#define CONFIG_BOARD_EARLY_INIT_R
	#define CONFIG_BOARD_LATE_INIT

	#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)

	#define CONFIG_TIMESTAMP

	/* FLASH related */
	#define CONFIG_MTD_DEVICE

	/*
	* uncomment the following to disable FLASH related code.
	*/
	/* #define CONFIG_SYS_NO_FLASH */

	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_FLASH_CFI

	#define CONFIG_SYS_MAX_FLASH_SECT 256
	#define CONFIG_SYS_MONITOR_BASE 0
	#define CONFIG_SYS_FLASH_BASE 0

	/*
	* flash_toggle does not work for out supoort card.
	* We need to use flash_status_poll.
	*/
	#define CONFIG_SYS_CFI_FLASH_STATUS_POLL

	#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */

	#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2

	/* serial console configuration */
	#define CONFIG_BAUDRATE 115200

	#define CONFIG_SYS_GENERIC_BOARD

	#if !defined(CONFIG_SPL_BUILD)
	#define CONFIG_USE_ARCH_MEMSET
	#define CONFIG_USE_ARCH_MEMCPY
	#endif

	#define CONFIG_SYS_LONGHELP /* undef to save memory */

	#define CONFIG_CMDLINE_EDITING /* add command line history */
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	/* Print Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_MAXARGS 16 /* max number of command */
	/* Boot Argument Buffer Size */
	#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)

	#define CONFIG_CONS_INDEX 1

	/*
	* For NAND booting the environment is embedded in the U-Boot image. Please take
	* look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
	*/
	/* #define CONFIG_ENV_IS_IN_NAND */
	#define CONFIG_ENV_IS_NOWHERE
	#define CONFIG_ENV_SIZE 0x2000
	#define CONFIG_ENV_OFFSET 0x0
	/* #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */

	/* Time clock 1MHz */
	#define CONFIG_SYS_TIMER_RATE 1000000

	/*
	* By default, ARP timeout is 5 sec.
	* The first ARP request does not seem to work.
	* So we need to retry ARP request anyway.
	* We want to shrink the interval until the second ARP request.
	*/
	#define CONFIG_ARP_TIMEOUT 500UL /* 0.5 msec */

	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_SYS_NAND_MAX_CHIPS 2
	#define CONFIG_SYS_NAND_ONFI_DETECTION

	#define CONFIG_NAND_DENALI_ECC_SIZE 1024

	#define CONFIG_SYS_NAND_REGS_BASE 0x68100000
	#define CONFIG_SYS_NAND_DATA_BASE 0x68000000

	#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_DATA_BASE + 0x10)

	#define CONFIG_SYS_NAND_USE_FLASH_BBT
	#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0

	/* USB */
	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
	#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 4
	#define CONFIG_CMD_FAT
	#define CONFIG_FAT_WRITE
	#define CONFIG_DOS_PARTITION

	/* memtest works on */
	#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
	#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01000000)

	#define CONFIG_BOOTDELAY 3
	#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
	#define CONFIG_AUTOBOOT_KEYED 1
	#define CONFIG_AUTOBOOT_PROMPT \
	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
	#define CONFIG_AUTOBOOT_DELAY_STR "d"
	#define CONFIG_AUTOBOOT_STOP_STR " "

	/*
	* Network Configuration
	*/
	#define CONFIG_ETHADDR 00:21:83:24:00:00
	#define CONFIG_SERVERIP 192.168.11.1
	#define CONFIG_IPADDR 192.168.11.10
	#define CONFIG_GATEWAYIP 192.168.11.1
	#define CONFIG_NETMASK 255.255.255.0

	#define CONFIG_LOADADDR 0x84000000
	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
	#define CONFIG_BOOTFILE "fit.itb"

	#define CONFIG_CMDLINE_EDITING /* add command line history */

	#define CONFIG_BOOTCOMMAND "run $bootmode"

	#define CONFIG_ROOTPATH "/nfs/root/path"
	#define CONFIG_NFSBOOTCOMMAND \
	"setenv bootargs $bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \
	"tftpboot; bootm;"

	#define CONFIG_BOOTARGS " user_debug=0x1f init=/sbin/init"

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"image_offset=0x00080000\0" \
	"image_size=0x00f00000\0" \
	"verify=n\0" \
	"nandupdate=nand erase 0 0x100000 &&" \
	"tftpboot u-boot-spl.bin &&" \
	"nand write $loadaddr 0 0x10000 &&" \
	"tftpboot u-boot-dtb.img &&" \
	"nand write $loadaddr 0x10000 0xf0000\0" \
	"norboot=run add_default_bootargs &&" \
	"bootm $image_offset\0" \
	"nandboot=run add_default_bootargs &&" \
	"nand read $loadaddr $image_offset $image_size &&" \
	"bootm\0" \
	"add_default_bootargs=setenv bootargs $bootargs" \
	" console=ttyS0,$baudrate\0" \

	/* Open Firmware flat tree */
	#define CONFIG_OF_LIBFDT

	#define CONFIG_HAVE_ARM_SECURE

	/* Memory Size & Mapping */
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SDRAM0_BASE

	#if CONFIG_SDRAM0_BASE + CONFIG_SDRAM0_SIZE >= CONFIG_SDRAM1_BASE
	/* Thre is no memory hole */
	#define CONFIG_NR_DRAM_BANKS 1
	#define CONFIG_SYS_SDRAM_SIZE (CONFIG_SDRAM0_SIZE + CONFIG_SDRAM1_SIZE)
	#else
	#define CONFIG_NR_DRAM_BANKS 2
	#define CONFIG_SYS_SDRAM_SIZE (CONFIG_SDRAM0_SIZE)
	#endif

	#define CONFIG_SYS_TEXT_BASE 0x84000000

	#if defined(CONFIG_MACH_PH1_LD4) \|\| defined(CONFIG_MACH_PH1_SLD8)
	#define CONFIG_SPL_TEXT_BASE 0x00040000
	#endif
	#if defined(CONFIG_MACH_PH1_PRO4)
	#define CONFIG_SPL_TEXT_BASE 0x00100000
	#endif

	#ifndef CONFIG_SPL_BUILD
	#define CONFIG_SKIP_LOWLEVEL_INIT
	#endif

	#define CONFIG_SYS_SPL_MALLOC_START (0x0ff00000)
	#define CONFIG_SYS_SPL_MALLOC_SIZE (0x00004000)

	#ifdef CONFIG_SPL_BUILD
	#define CONFIG_SYS_INIT_SP_ADDR (0x0ff08000)
	#else
	#define CONFIG_SYS_INIT_SP_ADDR ((CONFIG_SYS_TEXT_BASE) - 0x00001000)
	#endif

	#define CONFIG_SPL_FRAMEWORK
	#define CONFIG_SPL_NAND_SUPPORT

	#define CONFIG_SPL_LIBCOMMON_SUPPORT /* for mem_malloc_init */
	#define CONFIG_SPL_LIBGENERIC_SUPPORT

	#define CONFIG_SPL_BOARD_INIT

	#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x10000

	#endif /* __CONFIG_UNIPHIER_COMMON_H__ */