| CONFIG_PPC=y |
| CONFIG_SYS_IMMR=0xFFE00000 |
| CONFIG_SYS_TEXT_BASE=0x11001000 |
| CONFIG_SYS_MALLOC_LEN=0x100000 |
| CONFIG_ENV_SIZE=0x20000 |
| CONFIG_ENV_OFFSET=0x100000 |
| CONFIG_DEFAULT_DEVICE_TREE="p1020rdb-pd" |
| CONFIG_SPL_TEXT_BASE=0xFF800000 |
| CONFIG_SPL_SERIAL=y |
| CONFIG_TPL_TEXT_BASE=0xF8F81000 |
| CONFIG_TPL_LIBCOMMON_SUPPORT=y |
| CONFIG_TPL_LIBGENERIC_SUPPORT=y |
| CONFIG_TPL_SERIAL=y |
| CONFIG_SPL=y |
| CONFIG_MPC85xx=y |
| # CONFIG_CMD_ERRATA is not set |
| CONFIG_TARGET_P1020RDB_PD=y |
| CONFIG_MP=y |
| CONFIG_FIT=y |
| CONFIG_FIT_VERBOSE=y |
| CONFIG_OF_BOARD_SETUP=y |
| CONFIG_OF_STDOUT_VIA_ALIAS=y |
| CONFIG_TPL_SYS_MONITOR_BASE=0xF8F81000 |
| CONFIG_BOOTDELAY=10 |
| CONFIG_USE_BOOTCOMMAND=y |
| CONFIG_BOOTCOMMAND="setenv bootargs root=/dev/$bdev rw rootdelay=30 console=$consoledev,$baudrate $othbootargs;usb start;ext2load usb 0:1 $loadaddr /boot/$bootfile;ext2load usb 0:1 $fdtaddr /boot/$fdtfile;bootm $loadaddr - $fdtaddr" |
| CONFIG_BOARD_EARLY_INIT_F=y |
| CONFIG_BOARD_EARLY_INIT_R=y |
| # CONFIG_MISC_INIT_R is not set |
| # CONFIG_SPL_FRAMEWORK is not set |
| CONFIG_SPL_MAX_SIZE=0x1000 |
| CONFIG_SPL_NAND_BOOT=y |
| CONFIG_SPL_SYS_CCSR_DO_NOT_RELOCATE=y |
| CONFIG_SPL_INIT_MINIMAL=y |
| CONFIG_SPL_FLUSH_IMAGE=y |
| CONFIG_SPL_NAND_SUPPORT=y |
| CONFIG_TPL=y |
| CONFIG_TPL_MAX_SIZE=0x20000 |
| CONFIG_TPL_ENV_SUPPORT=y |
| CONFIG_TPL_I2C=y |
| CONFIG_TPL_MPC8XXX_INIT_DDR=y |
| CONFIG_TPL_NAND_SUPPORT=y |
| CONFIG_HUSH_PARSER=y |
| # CONFIG_AUTO_COMPLETE is not set |
| CONFIG_SYS_PBSIZE=276 |
| CONFIG_CMD_IMLS=y |
| CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3 |
| CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 |
| CONFIG_CMD_I2C=y |
| CONFIG_CMD_MMC=y |
| CONFIG_CMD_USB=y |
| CONFIG_CMD_MII=y |
| CONFIG_CMD_PING=y |
| # CONFIG_CMD_HASH is not set |
| CONFIG_CMD_EXT2=y |
| CONFIG_CMD_FAT=y |
| CONFIG_CMD_MTDPARTS=y |
| CONFIG_MTDIDS_DEFAULT="nor0=ec000000.nor" |
| CONFIG_MTDPARTS_DEFAULT="mtdparts=ec000000.nor:128k(dtb),6016k(kernel),57088k(fs),1m(vsc7385-firmware),1280k(u-boot)" |
| CONFIG_OF_CONTROL=y |
| CONFIG_ENV_OVERWRITE=y |
| CONFIG_ENV_IS_IN_NAND=y |
| CONFIG_SYS_RELOC_GD_ENV_ADDR=y |
| CONFIG_USE_BOOTFILE=y |
| CONFIG_BOOTFILE="uImage" |
| CONFIG_USE_ETHPRIME=y |
| CONFIG_ETHPRIME="eTSEC1" |
| CONFIG_DM=y |
| CONFIG_DDR_CLK_FREQ=66666666 |
| CONFIG_CHIP_SELECTS_PER_CTRL=2 |
| CONFIG_SYS_BR0_PRELIM_BOOL=y |
| CONFIG_SYS_BR0_PRELIM=0xFF800C21 |
| CONFIG_SYS_OR0_PRELIM=0xFFFF8796 |
| CONFIG_SYS_BR1_PRELIM_BOOL=y |
| CONFIG_SYS_BR1_PRELIM=0xEC001001 |
| CONFIG_SYS_OR1_PRELIM=0xFC000FF7 |
| CONFIG_SYS_BR2_PRELIM_BOOL=y |
| CONFIG_SYS_BR2_PRELIM=0xFFB00801 |
| CONFIG_SYS_OR2_PRELIM=0xFFFE09FF |
| CONFIG_SYS_BR3_PRELIM_BOOL=y |
| CONFIG_SYS_BR3_PRELIM=0xFFA00801 |
| CONFIG_SYS_OR3_PRELIM=0xFFF009F7 |
| CONFIG_TPL_COMMON_INIT_DDR=y |
| CONFIG_DM_I2C=y |
| CONFIG_SPL_SYS_I2C_LEGACY=y |
| CONFIG_TPL_SYS_I2C_LEGACY=y |
| CONFIG_I2C_SET_DEFAULT_BUS_NUM=y |
| CONFIG_SYS_I2C_FSL=y |
| CONFIG_SYS_FSL_I2C_OFFSET=0x3000 |
| CONFIG_SYS_FSL_HAS_I2C2_OFFSET=y |
| CONFIG_SYS_FSL_I2C2_OFFSET=0x3100 |
| CONFIG_SYS_I2C_EEPROM_ADDR=0x52 |
| CONFIG_FSL_ESDHC=y |
| CONFIG_MTD=y |
| CONFIG_MTD_NOR_FLASH=y |
| CONFIG_FLASH_CFI_DRIVER=y |
| CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y |
| CONFIG_FLASH_CFI_MTD=y |
| CONFIG_SYS_FLASH_CFI=y |
| CONFIG_MTD_RAW_NAND=y |
| CONFIG_NAND_FSL_ELBC=y |
| CONFIG_SYS_NAND_BLOCK_SIZE=0x20000 |
| CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y |
| CONFIG_SYS_NAND_U_BOOT_OFFS=0x20000 |
| CONFIG_DM_SPI_FLASH=y |
| CONFIG_SF_DEFAULT_SPEED=10000000 |
| CONFIG_SPI_FLASH_SPANSION=y |
| CONFIG_PHY_ATHEROS=y |
| CONFIG_PHY_BROADCOM=y |
| CONFIG_PHY_DAVICOM=y |
| CONFIG_PHY_LXT=y |
| CONFIG_PHY_MARVELL=y |
| CONFIG_PHY_NATSEMI=y |
| CONFIG_PHY_REALTEK=y |
| CONFIG_PHY_SMSC=y |
| CONFIG_PHY_VITESSE=y |
| CONFIG_PHY_FIXED=y |
| CONFIG_DM_ETH=y |
| CONFIG_DM_MDIO=y |
| CONFIG_PHY_GIGE=y |
| CONFIG_E1000=y |
| CONFIG_MII=y |
| CONFIG_TSEC_ENET=y |
| CONFIG_PCIE_FSL=y |
| CONFIG_DM_RTC=y |
| CONFIG_SYS_NS16550=y |
| CONFIG_SPI=y |
| CONFIG_DM_SPI=y |
| CONFIG_FSL_ESPI=y |
| CONFIG_USB=y |
| CONFIG_USB_EHCI_FSL=y |
| CONFIG_USB_STORAGE=y |