| /* |
| * (C) Copyright 2000-2005 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_405EP 1 /* This is a PPC405 CPU */ |
| #define CONFIG_4xx 1 /* ...member of PPC4xx family */ |
| #define CONFIG_BUBINGA 1 /* ...on a BUBINGA board */ |
| |
| /* |
| * Include common defines/options for all AMCC eval boards |
| */ |
| #define CONFIG_HOSTNAME bubinga |
| #include "amcc-common.h" |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ |
| |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ |
| |
| #define CONFIG_NO_SERIAL_EEPROM |
| /*#undef CONFIG_NO_SERIAL_EEPROM*/ |
| /*----------------------------------------------------------------------------*/ |
| #ifdef CONFIG_NO_SERIAL_EEPROM |
| |
| /* |
| !------------------------------------------------------------------------------- |
| ! Defines for entry options. |
| ! Note: Because the 405EP SDRAM controller does not support ECC, ECC DIMMs that |
| ! are plugged in the board will be utilized as non-ECC DIMMs. |
| !------------------------------------------------------------------------------- |
| */ |
| #define AUTO_MEMORY_CONFIG |
| #define DIMM_READ_ADDR 0xAB |
| #define DIMM_WRITE_ADDR 0xAA |
| |
| /* |
| !------------------------------------------------------------------------------- |
| ! PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI, |
| ! assuming a 33MHz input clock to the 405EP from the C9531. |
| !------------------------------------------------------------------------------- |
| */ |
| #define PLLMR0_DEFAULT PLLMR0_266_133_66 |
| #define PLLMR1_DEFAULT PLLMR1_266_133_66 |
| |
| #endif |
| /*----------------------------------------------------------------------------*/ |
| |
| /* |
| * Define here the location of the environment variables (FLASH or NVRAM). |
| * Note: DENX encourages to use redundant environment in FLASH. NVRAM is only |
| * supported for backward compatibility. |
| */ |
| #if 1 |
| #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ |
| #else |
| #define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ |
| #endif |
| |
| /* |
| * Default environment variables |
| */ |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| CONFIG_AMCC_DEF_ENV \ |
| CONFIG_AMCC_DEF_ENV_PPC \ |
| CONFIG_AMCC_DEF_ENV_NOR_UPD \ |
| "kernel_addr=fff80000\0" \ |
| "ramdisk_addr=fff90000\0" \ |
| "" |
| |
| #define CONFIG_PHY_ADDR 1 /* PHY address */ |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */ |
| |
| #define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Bubinga */ |
| |
| /* |
| * Commands additional to the ones defined in amcc-common.h |
| */ |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_SDRAM |
| #define CONFIG_CMD_SNTP |
| |
| #define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ |
| |
| /* |
| * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1. |
| * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31. |
| * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value. |
| * The Linux BASE_BAUD define should match this configuration. |
| * baseBaud = cpuClock/(uartDivisor*16) |
| * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, |
| * set Linux BASE_BAUD to 403200. |
| */ |
| #undef CONFIG_SERIAL_SOFTWARE_FIFO |
| #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ |
| #undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ |
| #define CONFIG_SYS_BASE_BAUD 691200 |
| |
| /*----------------------------------------------------------------------- |
| * I2C stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ |
| |
| #define CONFIG_SYS_I2C_NOPROBES { 0x69 } /* avoid i2c probe hangup (why?) */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ |
| |
| #if defined(CONFIG_CMD_EEPROM) |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* I2C boot EEPROM (24C02W) */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ |
| #define PCI_HOST_FORCE 1 /* configure as pci host */ |
| #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ |
| |
| #define CONFIG_PCI /* include pci support */ |
| #define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| /* resource configuration */ |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ |
| #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ |
| #define CONFIG_SYS_PCI_CLASSCODE 0x0600 /* PCI Class Code: bridge/host */ |
| #define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ |
| #define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ |
| #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ |
| #define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ |
| #define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ |
| #define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ |
| |
| /*----------------------------------------------------------------------- |
| * External peripheral base address |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000 |
| #define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000 |
| #define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000 |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| */ |
| #define CONFIG_SYS_SRAM_BASE 0xFFF00000 |
| #define CONFIG_SYS_FLASH_BASE 0xFFF80000 |
| |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #define CONFIG_SYS_FLASH_ADDR0 0x5555 |
| #define CONFIG_SYS_FLASH_ADDR1 0x2aaa |
| #define CONFIG_SYS_FLASH_WORD_SIZE unsigned char |
| |
| #ifdef CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) |
| #endif /* CONFIG_ENV_IS_IN_FLASH */ |
| |
| /*----------------------------------------------------------------------- |
| * NVRAM organization |
| */ |
| #define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */ |
| #define CONFIG_SYS_NVRAM_SIZE 0x1ff8 /* NVRAM size */ |
| |
| #ifdef CONFIG_ENV_IS_IN_NVRAM |
| #define CONFIG_ENV_SIZE 0x0ff8 /* Size of Environment vars */ |
| #define CONFIG_ENV_ADDR \ |
| (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */ |
| #endif |
| |
| /* |
| * Init Memory Controller: |
| * |
| * BR0/1 and OR0/1 (FLASH) |
| */ |
| |
| #define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ |
| #define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area (in data cache) |
| */ |
| /* use on chip memory ( OCM ) for temperary stack until sdram is tested */ |
| #define CONFIG_SYS_TEMP_STACK_OCM 1 |
| |
| /* On Chip Memory location */ |
| #define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 |
| #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ |
| #define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */ |
| |
| #define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /*----------------------------------------------------------------------- |
| * External Bus Controller (EBC) Setup |
| */ |
| |
| /* Memory Bank 0 (Flash/SRAM) initialization */ |
| #define CONFIG_SYS_EBC_PB0AP 0x04006000 |
| #define CONFIG_SYS_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */ |
| |
| /* Memory Bank 1 (NVRAM/RTC) initialization */ |
| #define CONFIG_SYS_EBC_PB1AP 0x04041000 |
| #define CONFIG_SYS_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ |
| |
| /* Memory Bank 2 (not used) initialization */ |
| #define CONFIG_SYS_EBC_PB2AP 0x00000000 |
| #define CONFIG_SYS_EBC_PB2CR 0x00000000 |
| |
| /* Memory Bank 2 (not used) initialization */ |
| #define CONFIG_SYS_EBC_PB3AP 0x00000000 |
| #define CONFIG_SYS_EBC_PB3CR 0x00000000 |
| |
| /* Memory Bank 4 (FPGA regs) initialization */ |
| #define CONFIG_SYS_EBC_PB4AP 0x01815000 |
| #define CONFIG_SYS_EBC_PB4CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */ |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for Serial Presence Detect EEPROM address |
| * (to get SDRAM settings) |
| */ |
| #define SPD_EEPROM_ADDRESS 0x55 |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for GPIO setup (PPC405EP specific) |
| * |
| * GPIO0[0] - External Bus Controller BLAST output |
| * GPIO0[1-9] - Instruction trace outputs |
| * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs |
| * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs |
| * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs |
| * GPIO0[24-27] - UART0 control signal inputs/outputs |
| * GPIO0[28-29] - UART1 data signal input/output |
| * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs |
| */ |
| #define CONFIG_SYS_GPIO0_OSRH 0x55555555 |
| #define CONFIG_SYS_GPIO0_OSRL 0x40000110 |
| #define CONFIG_SYS_GPIO0_ISR1H 0x00000000 |
| #define CONFIG_SYS_GPIO0_ISR1L 0x15555445 |
| #define CONFIG_SYS_GPIO0_TSRH 0x00000000 |
| #define CONFIG_SYS_GPIO0_TSRL 0x00000000 |
| #define CONFIG_SYS_GPIO0_TCR 0xFFFF8014 |
| |
| /*----------------------------------------------------------------------- |
| * Some BUBINGA stuff... |
| */ |
| #define NVRAM_BASE 0xF0000000 |
| #define FPGA_REG0 0xF0300000 /* FPGA Reg 0 */ |
| #define FPGA_REG1 0xF0300001 /* FPGA Reg 1 */ |
| #define NVRVFY1 0x4f532d4f /* used to determine if state data in */ |
| #define NVRVFY2 0x50454e00 /* NVRAM initialized (ascii for OS-OPEN)*/ |
| |
| #define FPGA_REG0_F_RANGE 0x80 /* SDRAM PLL freq range */ |
| #define FPGA_REG0_EXT_INT_DIS 0x20 /* External interface disable */ |
| #define FPGA_REG0_LED_MASK 0x07 /* Board LEDs DS9, DS10, and DS11 */ |
| #define FPGA_REG0_LED0 0x04 /* Turn on LED0 */ |
| #define FPGA_REG0_LED1 0x02 /* Turn on LED1 */ |
| #define FPGA_REG0_LED2 0x01 /* Turn on LED2 */ |
| |
| #define FPGA_REG1_SSPEC_DIS 0x80 /* C9531 Spread Spectrum disabled */ |
| #define FPGA_REG1_OFFBD_PCICLK 0x40 /* Onboard PCI clock selected */ |
| #define FPGA_REG1_CLOCK_MASK 0x30 /* Mask for C9531 output freq select */ |
| #define FPGA_REG1_CLOCK_BIT_SHIFT 4 |
| #define FPGA_REG1_PCI_INT_ARB 0x08 /* PCI Internal arbiter selected */ |
| #define FPGA_REG1_PCI_FREQ 0x04 /* PCI Frequency select */ |
| #define FPGA_REG1_OFFB_FLASH 0x02 /* Off board flash */ |
| #define FPGA_REG1_SRAM_BOOT 0x01 /* SRAM at 0xFFF80000 not Flash */ |
| |
| #endif /* __CONFIG_H */ |