include/configs/ML2.h - platform/external/u-boot - Gitiles

 /*
  * ML2.h: ML2 specific config options
  *
  * Copyright 2002 Mind NV
  *
  * http://www.mind.be/
  *
  * Author : Peter De Schrijver (p2@mind.be)
  *
  * Derived from : other configuration header files in this tree
  *
  * This software may be used and distributed according to the terms of
  * the GNU General Public License (GPL) version 2, incorporated herein by
  * reference. Drivers based on or derived from this code fall under the GPL
  * and must retain the authorship, copyright and this license notice. This
  * file is not a complete program and may only be used when the entire
  * program is licensed under the GPL.
  *
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */

 #define CONFIG_405		1	/* This is a PPC405 CPU		*/
 #define CONFIG_4xx		1	/* ...member of PPC4xx family   */
 #define CONFIG_ML2	1	/* ...on a ML2 board	*/


 #define CONFIG_ENV_IS_IN_FLASH     1

 #ifdef CONFIG_ENV_IS_IN_NVRAM
 #undef CONFIG_ENV_IS_IN_FLASH
 #else
 #ifdef CONFIG_ENV_IS_IN_FLASH
 #undef CONFIG_ENV_IS_IN_NVRAM
 #endif
 #endif

 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/

 #if 1
 #define CONFIG_BOOTCOMMAND	"bootm" /* autoboot command	*/
 #else
 #define CONFIG_BOOTCOMMAND	"bootp" /* autoboot command		*/
 #endif

 #define CONFIG_PREBOOT		"fsload 0x00100000 /boot/image"

 /* Size (bytes) of interrupt driven serial port buffer.
  * Set to 0 to use polling instead of interrupts.
  * Setting to 0 will also disable RTS/CTS handshaking.
  */
 #if 0
 #define CONFIG_SERIAL_SOFTWARE_FIFO 4000
 #else
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #endif

 #if 0
 #define CONFIG_BOOTARGS		"root=/dev/nfs "                        \
     "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 "        \
     "nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4"
 #else
 #define CONFIG_BOOTARGS		"root=/dev/mtdblock2 "			\
    "console=ttyS0 console=tty"

 #endif

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/


 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_KGDB
 #define CONFIG_CMD_BEDBUG
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_JFFS2

 #undef CONFIG_CMD_NET
 #undef CONFIG_CMD_RTC
 #undef CONFIG_CMD_PCI
 #undef CONFIG_CMD_I2C


 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/

 #define CONFIG_SYS_CLK_FREQ 50000000

 #define CONFIG_SPD_EEPROM      1       /* use SPD EEPROM for setup    */

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
 #define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
 #define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

 #define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

 /*
  * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
  * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
  * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
  * The Linux BASE_BAUD define should match this configuration.
  *    baseBaud = cpuClock/(uartDivisor*16)
  * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
  * set Linux BASE_BAUD to 403200.
  */
 #undef  CONFIG_SYS_EXT_SERIAL_CLOCK           /* external serial clock */
 #undef  CONFIG_SYS_405_UART_ERRATA_59         /* 405GP/CR Rev. D silicon */

 #define CONFIG_SYS_BASE_BAUD       (3125000*16)
 #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_BASE_BAUD
 #define CONFIG_SYS_DUART_CHAN		0
 #define CONFIG_SYS_NS16550_COM1	0xa0001003
 #define CONFIG_SYS_NS16550_COM2	0xa0011003
 #define CONFIG_SYS_NS16550_REG_SIZE -4
 #define CONFIG_SYS_NS16550 1
 #define CONFIG_SYS_INIT_CHAN1	 1
 #define CONFIG_SYS_INIT_CHAN2	 1

 /* The following table includes the supported baudrates */
 #define CONFIG_SYS_BAUDRATE_TABLE  \
     {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}

 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
 #define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */

 #define	CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks	*/


 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_FLASH_BASE		0x18000000
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_MONITOR_LEN		(192 * 1024)	/* Reserve 196 kB for Monitor	*/
 #define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
 #define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/

 #define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

 /* BEG ENVIRONNEMENT FLASH */
 #ifdef CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_OFFSET		0x00050000 /* Offset of Environment Sector  */
 #define	CONFIG_ENV_SIZE		0x10000	/* Total Size of Environment Sector	*/
 #define CONFIG_ENV_SECT_SIZE	0x10000	/* see README - env sector total size	*/
 #endif
 /* END ENVIRONNEMENT FLASH */
 /*-----------------------------------------------------------------------
  * NVRAM organization
  */
 #define CONFIG_SYS_NVRAM_BASE_ADDR	0xf0000000	/* NVRAM base address	*/
 #define CONFIG_SYS_NVRAM_SIZE		0x1ff8		/* NVRAM size	*/

 #ifdef CONFIG_ENV_IS_IN_NVRAM
 #define CONFIG_ENV_SIZE		0x1000		/* Size of Environment vars	*/
 #define CONFIG_ENV_ADDR		\
 	(CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE)	/* Env	*/
 #endif

 /*
  * Init Memory Controller:
  *
  * BR0/1 and OR0/1 (FLASH)
  */

 #define FLASH_BASE0_PRELIM	CONFIG_SYS_FLASH_BASE	/* FLASH bank #0	*/
 #define FLASH_BASE1_PRELIM	0		/* FLASH bank #1	*/


 /* Configuration Port location */
 #define CONFIG_PORT_ADDR	0xF0000500

 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */

 #define CONFIG_SYS_INIT_RAM_ADDR       0x800000  /* inside of SDRAM                     */
 #define CONFIG_SYS_INIT_RAM_END        0x2000  /* End of used area in RAM             */
 #define CONFIG_SYS_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET

 /*-----------------------------------------------------------------------
  * Definitions for Serial Presence Detect EEPROM address
  * (to get SDRAM settings)
  */
 #define SPD_EEPROM_ADDRESS      0x50

 /*
  * Internal Definitions
  *
  * Boot Flags
  */
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif

 /*
  * JFFS2 partitions
  *
  */
 /* No command line, one static partition, whole device */
 #undef CONFIG_JFFS2_CMDLINE
 #define CONFIG_JFFS2_DEV		"nor0"
 #define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
 #define CONFIG_JFFS2_PART_OFFSET	0x00080000

 /* mtdparts command line support */
 /* Note: fake mtd_id used, no linux mtd map file */
 /*
 #define CONFIG_JFFS2_CMDLINE
 #define MTDIDS_DEFAULT		"nor0=ml2-0"
 #define MTDPARTS_DEFAULT	"mtdparts=ml2-0:-@512k(jffs2)"
 */

 #endif	/* __CONFIG_H */
	/*
	* ML2.h: ML2 specific config options
	*
	* Copyright 2002 Mind NV
	*
	* http://www.mind.be/
	*
	* Author : Peter De Schrijver (p2@mind.be)
	*
	* Derived from : other configuration header files in this tree
	*
	* This software may be used and distributed according to the terms of
	* the GNU General Public License (GPL) version 2, incorporated herein by
	* reference. Drivers based on or derived from this code fall under the GPL
	* and must retain the authorship, copyright and this license notice. This
	* file is not a complete program and may only be used when the entire
	* program is licensed under the GPL.
	*
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/

	#define CONFIG_405 1 /* This is a PPC405 CPU */
	#define CONFIG_4xx 1 /* ...member of PPC4xx family */
	#define CONFIG_ML2 1 /* ...on a ML2 board */


	#define CONFIG_ENV_IS_IN_FLASH 1

	#ifdef CONFIG_ENV_IS_IN_NVRAM
	#undef CONFIG_ENV_IS_IN_FLASH
	#else
	#ifdef CONFIG_ENV_IS_IN_FLASH
	#undef CONFIG_ENV_IS_IN_NVRAM
	#endif
	#endif

	#define CONFIG_BAUDRATE 9600
	#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */

	#if 1
	#define CONFIG_BOOTCOMMAND "bootm" /* autoboot command */
	#else
	#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
	#endif

	#define CONFIG_PREBOOT "fsload 0x00100000 /boot/image"

	/* Size (bytes) of interrupt driven serial port buffer.
	* Set to 0 to use polling instead of interrupts.
	* Setting to 0 will also disable RTS/CTS handshaking.
	*/
	#if 0
	#define CONFIG_SERIAL_SOFTWARE_FIFO 4000
	#else
	#undef CONFIG_SERIAL_SOFTWARE_FIFO
	#endif

	#if 0
	#define CONFIG_BOOTARGS "root=/dev/nfs " \
	"ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 " \
	"nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4"
	#else
	#define CONFIG_BOOTARGS "root=/dev/mtdblock2 " \
	"console=ttyS0 console=tty"

	#endif

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */


	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_IRQ
	#define CONFIG_CMD_KGDB
	#define CONFIG_CMD_BEDBUG
	#define CONFIG_CMD_ELF
	#define CONFIG_CMD_JFFS2

	#undef CONFIG_CMD_NET
	#undef CONFIG_CMD_RTC
	#undef CONFIG_CMD_PCI
	#undef CONFIG_CMD_I2C


	#undef CONFIG_WATCHDOG /* watchdog disabled */

	#define CONFIG_SYS_CLK_FREQ 50000000

	#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */

	/*
	* If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
	* If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
	* Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
	* The Linux BASE_BAUD define should match this configuration.
	* baseBaud = cpuClock/(uartDivisor*16)
	* If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
	* set Linux BASE_BAUD to 403200.
	*/
	#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
	#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */

	#define CONFIG_SYS_BASE_BAUD (3125000*16)
	#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_BASE_BAUD
	#define CONFIG_SYS_DUART_CHAN 0
	#define CONFIG_SYS_NS16550_COM1 0xa0001003
	#define CONFIG_SYS_NS16550_COM2 0xa0011003
	#define CONFIG_SYS_NS16550_REG_SIZE -4
	#define CONFIG_SYS_NS16550 1
	#define CONFIG_SYS_INIT_CHAN1 1
	#define CONFIG_SYS_INIT_CHAN2 1

	/* The following table includes the supported baudrates */
	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}

	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
	#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */

	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */


	/*-----------------------------------------------------------------------
	* Start addresses for the final memory configuration
	* (Set up by the startup code)
	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
	*/
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_FLASH_BASE 0x18000000
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */
	#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
	/*-----------------------------------------------------------------------
	* FLASH organization
	*/
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */

	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */

	/* BEG ENVIRONNEMENT FLASH */
	#ifdef CONFIG_ENV_IS_IN_FLASH
	#define CONFIG_ENV_OFFSET 0x00050000 /* Offset of Environment Sector */
	#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
	#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
	#endif
	/* END ENVIRONNEMENT FLASH */
	/*-----------------------------------------------------------------------
	* NVRAM organization
	*/
	#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
	#define CONFIG_SYS_NVRAM_SIZE 0x1ff8 /* NVRAM size */

	#ifdef CONFIG_ENV_IS_IN_NVRAM
	#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */
	#define CONFIG_ENV_ADDR \
	(CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */
	#endif

	/*
	* Init Memory Controller:
	*
	* BR0/1 and OR0/1 (FLASH)
	*/

	#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
	#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */


	/* Configuration Port location */
	#define CONFIG_PORT_ADDR 0xF0000500

	/*-----------------------------------------------------------------------
	* Definitions for initial stack pointer and data area (in DPRAM)
	*/

	#define CONFIG_SYS_INIT_RAM_ADDR 0x800000 /* inside of SDRAM */
	#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */
	#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	/*-----------------------------------------------------------------------
	* Definitions for Serial Presence Detect EEPROM address
	* (to get SDRAM settings)
	*/
	#define SPD_EEPROM_ADDRESS 0x50

	/*
	* Internal Definitions
	*
	* Boot Flags
	*/
	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	#define BOOTFLAG_WARM 0x02 /* Software reboot */

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
	#endif

	/*
	* JFFS2 partitions
	*
	*/
	/* No command line, one static partition, whole device */
	#undef CONFIG_JFFS2_CMDLINE
	#define CONFIG_JFFS2_DEV "nor0"
	#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
	#define CONFIG_JFFS2_PART_OFFSET 0x00080000

	/* mtdparts command line support */
	/* Note: fake mtd_id used, no linux mtd map file */
	/*
	#define CONFIG_JFFS2_CMDLINE
	#define MTDIDS_DEFAULT "nor0=ml2-0"
	#define MTDPARTS_DEFAULT "mtdparts=ml2-0:-@512k(jffs2)"
	*/

	#endif /* __CONFIG_H */