| CONFIG_ARM=y |
| CONFIG_ARCH_SOCFPGA=y |
| CONFIG_SYS_MALLOC_LEN=0x4000000 |
| CONFIG_SYS_MALLOC_F_LEN=0x800 |
| CONFIG_ENV_SIZE=0x1000 |
| CONFIG_ENV_OFFSET=0x100000 |
| CONFIG_DM_GPIO=y |
| CONFIG_DEFAULT_DEVICE_TREE="socfpga_arria5_secu1" |
| CONFIG_SPL_TEXT_BASE=0xFFFF0000 |
| # CONFIG_SPL_MMC is not set |
| CONFIG_SPL_DRIVERS_MISC=y |
| CONFIG_TARGET_SOCFPGA_ARRIA5_SECU1=y |
| CONFIG_ENV_OFFSET_REDUND=0x120000 |
| # CONFIG_SPL_LIBDISK_SUPPORT is not set |
| # CONFIG_SPL_SPI is not set |
| CONFIG_BUILD_TARGET="u-boot-with-nand-spl.sfp" |
| CONFIG_DISTRO_DEFAULTS=y |
| CONFIG_SYS_LOAD_ADDR=0x02000000 |
| CONFIG_FIT=y |
| CONFIG_USE_BOOTARGS=y |
| CONFIG_BOOTARGS="console=ttyS0,115200 ubi.fm_autoconvert=1 uio_pdrv_genirq.of_id=\"idq,regbank\"" |
| CONFIG_BOOTCOMMAND="setenv bootcmd 'bridge enable; if test ${bootnum} = 'b'; then run _fpga_loadsafe; else if test ${bootcount} -eq 4; then echo 'Switching copy...'; setexpr x $bootnum % 2 && setexpr bootnum $x + 1; saveenv; fi; run _fpga_loaduser; fi;echo 'Booting bank $bootnum' && run userload && run userboot;' && setenv altbootcmd 'setenv bootnum b && saveenv && boot;' && saveenv && saveenv && boot;" |
| CONFIG_DEFAULT_FDT_FILE="socfpga_arria5_secu1.dtb" |
| CONFIG_SYS_CONSOLE_IS_IN_ENV=y |
| CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y |
| CONFIG_SYS_CONSOLE_ENV_OVERWRITE=y |
| # CONFIG_DISPLAY_BOARDINFO is not set |
| CONFIG_DISPLAY_BOARDINFO_LATE=y |
| CONFIG_MISC_INIT_R=y |
| CONFIG_SPL_LEGACY_IMAGE_CRC_CHECK=y |
| # CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set |
| # CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION is not set |
| CONFIG_SPL_MTD_SUPPORT=y |
| CONFIG_CMD_ASKENV=y |
| CONFIG_CMD_GREPENV=y |
| CONFIG_CMD_EEPROM=y |
| CONFIG_SYS_I2C_EEPROM_ADDR_LEN=2 |
| CONFIG_SYS_EEPROM_SIZE=1024 |
| # CONFIG_CMD_FLASH is not set |
| CONFIG_CMD_GPIO=y |
| CONFIG_CMD_I2C=y |
| CONFIG_CMD_MMC=y |
| CONFIG_CMD_NAND_TRIMFFS=y |
| CONFIG_CMD_SPI=y |
| CONFIG_CMD_WDT=y |
| CONFIG_CMD_CACHE=y |
| CONFIG_MTDIDS_DEFAULT="nand0=denali-nand" |
| CONFIG_MTDPARTS_DEFAULT="mtdparts=denali-nand:512k(nand.4spl),512k(nand.uboot),128k(nand.env1),128k(nand.env2),0x1000000(nand.rec),0x3ee40000(nand.ubi),0x80000@0x3ff80000(nand.bbt)" |
| CONFIG_CMD_UBI=y |
| # CONFIG_CMD_UBIFS is not set |
| # CONFIG_ISO_PARTITION is not set |
| # CONFIG_EFI_PARTITION is not set |
| CONFIG_ENV_OVERWRITE=y |
| CONFIG_ENV_IS_IN_NAND=y |
| CONFIG_SYS_REDUNDAND_ENVIRONMENT=y |
| CONFIG_VERSION_VARIABLE=y |
| CONFIG_SPL_DM_SEQ_ALIAS=y |
| # CONFIG_SPL_BLK is not set |
| CONFIG_BOOTCOUNT_LIMIT=y |
| CONFIG_DM_BOOTCOUNT=y |
| CONFIG_DM_BOOTCOUNT_RTC=y |
| CONFIG_DWAPB_GPIO=y |
| CONFIG_DM_I2C=y |
| CONFIG_I2C_SET_DEFAULT_BUS_NUM=y |
| CONFIG_DM_I2C_GPIO=y |
| CONFIG_MISC=y |
| CONFIG_I2C_EEPROM=y |
| CONFIG_SYS_I2C_EEPROM_ADDR=0x50 |
| CONFIG_MMC_DW=y |
| CONFIG_MTD=y |
| CONFIG_DM_MTD=y |
| CONFIG_MTD_RAW_NAND=y |
| CONFIG_SYS_NAND_USE_FLASH_BBT=y |
| CONFIG_NAND_DENALI_DT=y |
| CONFIG_SYS_NAND_ONFI_DETECTION=y |
| CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y |
| CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000 |
| CONFIG_SPL_NAND_DENALI=y |
| CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES=2 |
| # CONFIG_DM_SPI_FLASH is not set |
| CONFIG_MTD_UBI_FASTMAP=y |
| CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT=1 |
| CONFIG_MV88E6352_SWITCH=y |
| CONFIG_PHY_FIXED=y |
| CONFIG_DM_ETH=y |
| CONFIG_PHY_GIGE=y |
| CONFIG_ETH_DESIGNWARE=y |
| CONFIG_MII=y |
| CONFIG_DM_RESET=y |
| CONFIG_DM_RTC=y |
| CONFIG_RTC_M41T62=y |
| CONFIG_SPI=y |
| CONFIG_SPI_MEM=y |
| CONFIG_DESIGNWARE_SPI=y |
| CONFIG_DESIGNWARE_WATCHDOG=y |
| CONFIG_WDT=y |
| # CONFIG_GZIP is not set |