| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * R8A66597 HCD (Host Controller Driver) for u-boot |
| * |
| * Copyright (C) 2008 Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> |
| */ |
| |
| #include <common.h> |
| #include <console.h> |
| #include <dm.h> |
| #include <log.h> |
| #include <usb.h> |
| #include <asm/io.h> |
| #include <dm/device_compat.h> |
| #include <linux/delay.h> |
| #include <linux/iopoll.h> |
| #include <power/regulator.h> |
| |
| #include "r8a66597.h" |
| |
| #ifdef R8A66597_DEBUG |
| #define R8A66597_DPRINT printf |
| #else |
| #define R8A66597_DPRINT(...) |
| #endif |
| |
| static inline struct usb_device *usb_dev_get_parent(struct usb_device *udev) |
| { |
| struct udevice *parent = udev->dev->parent; |
| |
| /* |
| * When called from usb-uclass.c: usb_scan_device() udev->dev points |
| * to the parent udevice, not the actual udevice belonging to the |
| * udev as the device is not instantiated yet. |
| * |
| * If dev is an usb-bus, then we are called from usb_scan_device() for |
| * an usb-device plugged directly into the root port, return NULL. |
| */ |
| if (device_get_uclass_id(udev->dev) == UCLASS_USB) |
| return NULL; |
| |
| /* |
| * If these 2 are not the same we are being called from |
| * usb_scan_device() and udev itself is the parent. |
| */ |
| if (dev_get_parent_priv(udev->dev) != udev) |
| return udev; |
| |
| /* We are being called normally, use the parent pointer */ |
| if (device_get_uclass_id(parent) == UCLASS_USB_HUB) |
| return dev_get_parent_priv(parent); |
| |
| return NULL; |
| } |
| |
| static void get_hub_data(struct usb_device *dev, u16 *hub_devnum, u16 *hubport) |
| { |
| struct usb_device *parent = usb_dev_get_parent(dev); |
| |
| *hub_devnum = 0; |
| *hubport = 0; |
| |
| /* check a device connected to root_hub */ |
| if ((parent && parent->devnum == 1) || |
| dev->devnum == 1) |
| return; |
| |
| *hub_devnum = (u8)parent->devnum; |
| *hubport = parent->portnr - 1; |
| } |
| |
| static void set_devadd(struct r8a66597 *r8a66597, u8 r8a66597_address, |
| struct usb_device *dev, int port) |
| { |
| u16 val, usbspd, upphub, hubport; |
| unsigned long devadd_reg = get_devadd_addr(r8a66597_address); |
| |
| get_hub_data(dev, &upphub, &hubport); |
| usbspd = r8a66597->speed; |
| val = (upphub << 11) | (hubport << 8) | (usbspd << 6) | (port & 0x0001); |
| r8a66597_write(r8a66597, val, devadd_reg); |
| } |
| |
| static int r8a66597_clock_enable(struct r8a66597 *r8a66597) |
| { |
| u16 tmp; |
| int i = 0; |
| |
| do { |
| r8a66597_write(r8a66597, USBE, SYSCFG0); |
| tmp = r8a66597_read(r8a66597, SYSCFG0); |
| if (i++ > 1000) { |
| printf("register access fail.\n"); |
| return -1; |
| } |
| } while ((tmp & USBE) != USBE); |
| r8a66597_bclr(r8a66597, USBE, SYSCFG0); |
| /* |
| * RZ/A Only: |
| * Bits XTAL(UCKSEL) and UPLLE in SYSCFG0 for USB0 controls both USB0 |
| * and USB1, so we must always set the USB0 register |
| */ |
| #if (CONFIG_R8A66597_XTAL == 1) |
| r8a66597_bset(r8a66597, XTAL, SYSCFG0); |
| #endif |
| mdelay(1); |
| r8a66597_bset(r8a66597, UPLLE, SYSCFG0); |
| mdelay(1); |
| r8a66597_bset(r8a66597, SUSPM, SUSPMODE0); |
| |
| return 0; |
| } |
| |
| static void r8a66597_clock_disable(struct r8a66597 *r8a66597) |
| { |
| r8a66597_bclr(r8a66597, SUSPM, SUSPMODE0); |
| |
| r8a66597_bclr(r8a66597, UPLLE, SYSCFG0); |
| mdelay(1); |
| r8a66597_bclr(r8a66597, USBE, SYSCFG0); |
| mdelay(1); |
| } |
| |
| static void r8a66597_enable_port(struct r8a66597 *r8a66597, int port) |
| { |
| u16 val; |
| |
| val = port ? DRPD : DCFM | DRPD; |
| r8a66597_bset(r8a66597, val, get_syscfg_reg(port)); |
| r8a66597_bset(r8a66597, HSE, get_syscfg_reg(port)); |
| } |
| |
| static void r8a66597_disable_port(struct r8a66597 *r8a66597, int port) |
| { |
| u16 val, tmp; |
| |
| r8a66597_write(r8a66597, 0, get_intenb_reg(port)); |
| r8a66597_write(r8a66597, 0, get_intsts_reg(port)); |
| |
| r8a66597_port_power(r8a66597, port, 0); |
| |
| do { |
| tmp = r8a66597_read(r8a66597, SOFCFG) & EDGESTS; |
| udelay(640); |
| } while (tmp == EDGESTS); |
| |
| val = port ? DRPD : DCFM | DRPD; |
| r8a66597_bclr(r8a66597, val, get_syscfg_reg(port)); |
| r8a66597_bclr(r8a66597, HSE, get_syscfg_reg(port)); |
| } |
| |
| static int enable_controller(struct r8a66597 *r8a66597) |
| { |
| int ret, port; |
| |
| ret = r8a66597_clock_enable(r8a66597); |
| if (ret < 0) |
| return ret; |
| |
| r8a66597_bset(r8a66597, USBE, SYSCFG0); |
| |
| r8a66597_bset(r8a66597, INTL, SOFCFG); |
| r8a66597_write(r8a66597, 0, INTENB0); |
| for (port = 0; port < R8A66597_MAX_ROOT_HUB; port++) |
| r8a66597_write(r8a66597, 0, get_intenb_reg(port)); |
| |
| r8a66597_bclr(r8a66597, BIGEND, CFIFOSEL); |
| r8a66597_bclr(r8a66597, BIGEND, D0FIFOSEL); |
| r8a66597_bclr(r8a66597, BIGEND, D1FIFOSEL); |
| r8a66597_bset(r8a66597, TRNENSEL, SOFCFG); |
| |
| for (port = 0; port < R8A66597_MAX_ROOT_HUB; port++) |
| r8a66597_enable_port(r8a66597, port); |
| |
| return 0; |
| } |
| |
| static void disable_controller(struct r8a66597 *r8a66597) |
| { |
| int i; |
| |
| if (!(r8a66597_read(r8a66597, SYSCFG0) & USBE)) |
| return; |
| |
| r8a66597_write(r8a66597, 0, INTENB0); |
| r8a66597_write(r8a66597, 0, INTSTS0); |
| |
| r8a66597_write(r8a66597, 0, D0FIFOSEL); |
| r8a66597_write(r8a66597, 0, D1FIFOSEL); |
| r8a66597_write(r8a66597, 0, DCPCFG); |
| r8a66597_write(r8a66597, 0x40, DCPMAXP); |
| r8a66597_write(r8a66597, 0, DCPCTR); |
| |
| for (i = 0; i <= 10; i++) |
| r8a66597_write(r8a66597, 0, get_devadd_addr(i)); |
| for (i = 1; i <= 5; i++) { |
| r8a66597_write(r8a66597, 0, get_pipetre_addr(i)); |
| r8a66597_write(r8a66597, 0, get_pipetrn_addr(i)); |
| } |
| for (i = 1; i < R8A66597_MAX_NUM_PIPE; i++) { |
| r8a66597_write(r8a66597, 0, get_pipectr_addr(i)); |
| r8a66597_write(r8a66597, i, PIPESEL); |
| r8a66597_write(r8a66597, 0, PIPECFG); |
| r8a66597_write(r8a66597, 0, PIPEBUF); |
| r8a66597_write(r8a66597, 0, PIPEMAXP); |
| r8a66597_write(r8a66597, 0, PIPEPERI); |
| } |
| |
| for (i = 0; i < R8A66597_MAX_ROOT_HUB; i++) |
| r8a66597_disable_port(r8a66597, i); |
| |
| r8a66597_clock_disable(r8a66597); |
| } |
| |
| static void r8a66597_reg_wait(struct r8a66597 *r8a66597, unsigned long reg, |
| u16 mask, u16 loop) |
| { |
| u16 tmp; |
| int i = 0; |
| |
| do { |
| tmp = r8a66597_read(r8a66597, reg); |
| if (i++ > 1000000) { |
| printf("register%lx, loop %x is timeout\n", reg, loop); |
| break; |
| } |
| } while ((tmp & mask) != loop); |
| } |
| |
| static void pipe_buffer_setting(struct r8a66597 *r8a66597, |
| struct usb_device *dev, unsigned long pipe) |
| { |
| u16 val = 0; |
| u16 pipenum, bufnum, maxpacket; |
| |
| if (usb_pipein(pipe)) { |
| pipenum = BULK_IN_PIPENUM; |
| bufnum = BULK_IN_BUFNUM; |
| maxpacket = dev->epmaxpacketin[usb_pipeendpoint(pipe)]; |
| } else { |
| pipenum = BULK_OUT_PIPENUM; |
| bufnum = BULK_OUT_BUFNUM; |
| maxpacket = dev->epmaxpacketout[usb_pipeendpoint(pipe)]; |
| } |
| |
| if (r8a66597->pipe_config & (1 << pipenum)) |
| return; |
| r8a66597->pipe_config |= (1 << pipenum); |
| |
| r8a66597_bset(r8a66597, ACLRM, get_pipectr_addr(pipenum)); |
| r8a66597_bclr(r8a66597, ACLRM, get_pipectr_addr(pipenum)); |
| r8a66597_write(r8a66597, pipenum, PIPESEL); |
| |
| /* FIXME: This driver support bulk transfer only. */ |
| if (!usb_pipein(pipe)) |
| val |= R8A66597_DIR; |
| else |
| val |= R8A66597_SHTNAK; |
| val |= R8A66597_BULK | R8A66597_DBLB | usb_pipeendpoint(pipe); |
| r8a66597_write(r8a66597, val, PIPECFG); |
| |
| r8a66597_write(r8a66597, (8 << 10) | bufnum, PIPEBUF); |
| r8a66597_write(r8a66597, make_devsel(usb_pipedevice(pipe)) | |
| maxpacket, PIPEMAXP); |
| r8a66597_write(r8a66597, 0, PIPEPERI); |
| r8a66597_write(r8a66597, SQCLR, get_pipectr_addr(pipenum)); |
| } |
| |
| static int send_setup_packet(struct r8a66597 *r8a66597, struct usb_device *dev, |
| struct devrequest *setup) |
| { |
| int i; |
| unsigned short *p = (unsigned short *)setup; |
| unsigned long setup_addr = USBREQ; |
| u16 intsts1; |
| int timeout = 3000; |
| u16 dcpctr; |
| u16 devsel = setup->request == USB_REQ_SET_ADDRESS ? 0 : dev->devnum; |
| |
| r8a66597_write(r8a66597, make_devsel(devsel) | |
| (8 << dev->maxpacketsize), DCPMAXP); |
| r8a66597_write(r8a66597, ~(SIGN | SACK), INTSTS1); |
| |
| dcpctr = r8a66597_read(r8a66597, DCPCTR); |
| if ((dcpctr & PID) == PID_BUF) { |
| if (readw_poll_timeout(r8a66597->reg + DCPCTR, dcpctr, |
| dcpctr & BSTS, 1000) < 0) { |
| printf("DCPCTR BSTS timeout!\n"); |
| return -ETIMEDOUT; |
| } |
| } |
| |
| for (i = 0; i < 4; i++) { |
| r8a66597_write(r8a66597, le16_to_cpu(p[i]), setup_addr); |
| setup_addr += 2; |
| } |
| r8a66597_write(r8a66597, ~0x0001, BRDYSTS); |
| r8a66597_write(r8a66597, SUREQ, DCPCTR); |
| |
| while (1) { |
| intsts1 = r8a66597_read(r8a66597, INTSTS1); |
| if (intsts1 & SACK) |
| break; |
| if (intsts1 & SIGN) { |
| printf("setup packet send error\n"); |
| return -1; |
| } |
| if (timeout-- < 0) { |
| printf("setup packet timeout\n"); |
| return -1; |
| } |
| udelay(500); |
| } |
| |
| return 0; |
| } |
| |
| static int send_bulk_packet(struct r8a66597 *r8a66597, struct usb_device *dev, |
| unsigned long pipe, void *buffer, int transfer_len) |
| { |
| u16 tmp, bufsize; |
| u16 *buf; |
| size_t size; |
| |
| R8A66597_DPRINT("%s\n", __func__); |
| |
| r8a66597_mdfy(r8a66597, MBW | BULK_OUT_PIPENUM, |
| MBW | CURPIPE, CFIFOSEL); |
| r8a66597_reg_wait(r8a66597, CFIFOSEL, CURPIPE, BULK_OUT_PIPENUM); |
| tmp = r8a66597_read(r8a66597, CFIFOCTR); |
| if ((tmp & FRDY) == 0) { |
| printf("%s FRDY is not set (%x)\n", __func__, tmp); |
| return -1; |
| } |
| |
| /* prepare parameters */ |
| bufsize = dev->epmaxpacketout[usb_pipeendpoint(pipe)]; |
| buf = (u16 *)(buffer + dev->act_len); |
| size = min((int)bufsize, transfer_len - dev->act_len); |
| |
| /* write fifo */ |
| r8a66597_write(r8a66597, ~(1 << BULK_OUT_PIPENUM), BEMPSTS); |
| if (buffer) { |
| r8a66597_write_fifo(r8a66597, CFIFO, buf, size); |
| r8a66597_write(r8a66597, BVAL, CFIFOCTR); |
| } |
| |
| /* update parameters */ |
| dev->act_len += size; |
| |
| r8a66597_mdfy(r8a66597, PID_BUF, PID, |
| get_pipectr_addr(BULK_OUT_PIPENUM)); |
| |
| while (!(r8a66597_read(r8a66597, BEMPSTS) & (1 << BULK_OUT_PIPENUM))) |
| if (ctrlc()) |
| return -1; |
| r8a66597_write(r8a66597, ~(1 << BULK_OUT_PIPENUM), BEMPSTS); |
| |
| if (dev->act_len >= transfer_len) |
| r8a66597_mdfy(r8a66597, PID_NAK, PID, |
| get_pipectr_addr(BULK_OUT_PIPENUM)); |
| |
| return 0; |
| } |
| |
| static int receive_bulk_packet(struct r8a66597 *r8a66597, |
| struct usb_device *dev, |
| unsigned long pipe, |
| void *buffer, int transfer_len) |
| { |
| u16 tmp; |
| u16 *buf; |
| const u16 pipenum = BULK_IN_PIPENUM; |
| int rcv_len; |
| int maxpacket = dev->epmaxpacketin[usb_pipeendpoint(pipe)]; |
| |
| R8A66597_DPRINT("%s\n", __func__); |
| |
| /* prepare */ |
| if (dev->act_len == 0) { |
| r8a66597_mdfy(r8a66597, PID_NAK, PID, |
| get_pipectr_addr(pipenum)); |
| r8a66597_write(r8a66597, ~(1 << pipenum), BRDYSTS); |
| |
| r8a66597_write(r8a66597, TRCLR, get_pipetre_addr(pipenum)); |
| r8a66597_write(r8a66597, |
| (transfer_len + maxpacket - 1) / maxpacket, |
| get_pipetrn_addr(pipenum)); |
| r8a66597_bset(r8a66597, TRENB, get_pipetre_addr(pipenum)); |
| |
| r8a66597_mdfy(r8a66597, PID_BUF, PID, |
| get_pipectr_addr(pipenum)); |
| } |
| |
| r8a66597_mdfy(r8a66597, MBW | pipenum, MBW | CURPIPE, CFIFOSEL); |
| r8a66597_reg_wait(r8a66597, CFIFOSEL, CURPIPE, pipenum); |
| |
| while (!(r8a66597_read(r8a66597, BRDYSTS) & (1 << pipenum))) |
| if (ctrlc()) |
| return -1; |
| r8a66597_write(r8a66597, ~(1 << pipenum), BRDYSTS); |
| |
| tmp = r8a66597_read(r8a66597, CFIFOCTR); |
| if ((tmp & FRDY) == 0) { |
| printf("%s FRDY is not set. (%x)\n", __func__, tmp); |
| return -1; |
| } |
| |
| buf = (u16 *)(buffer + dev->act_len); |
| rcv_len = tmp & DTLN; |
| dev->act_len += rcv_len; |
| |
| if (buffer) { |
| if (rcv_len == 0) |
| r8a66597_write(r8a66597, BCLR, CFIFOCTR); |
| else |
| r8a66597_read_fifo(r8a66597, CFIFO, buf, rcv_len); |
| } |
| |
| return 0; |
| } |
| |
| static int receive_control_packet(struct r8a66597 *r8a66597, |
| struct usb_device *dev, |
| void *buffer, int transfer_len) |
| { |
| u16 tmp; |
| int rcv_len; |
| |
| /* FIXME: limit transfer size : 64byte or less */ |
| |
| r8a66597_bclr(r8a66597, R8A66597_DIR, DCPCFG); |
| r8a66597_mdfy(r8a66597, 0, ISEL | CURPIPE, CFIFOSEL); |
| r8a66597_reg_wait(r8a66597, CFIFOSEL, CURPIPE, 0); |
| r8a66597_bset(r8a66597, SQSET, DCPCTR); |
| r8a66597_write(r8a66597, BCLR, CFIFOCTR); |
| r8a66597_mdfy(r8a66597, PID_BUF, PID, DCPCTR); |
| |
| while (!(r8a66597_read(r8a66597, BRDYSTS) & 0x0001)) |
| if (ctrlc()) |
| return -1; |
| r8a66597_write(r8a66597, ~0x0001, BRDYSTS); |
| |
| r8a66597_mdfy(r8a66597, MBW, MBW | CURPIPE, CFIFOSEL); |
| r8a66597_reg_wait(r8a66597, CFIFOSEL, CURPIPE, 0); |
| |
| tmp = r8a66597_read(r8a66597, CFIFOCTR); |
| if ((tmp & FRDY) == 0) { |
| printf("%s FRDY is not set. (%x)\n", __func__, tmp); |
| return -1; |
| } |
| |
| rcv_len = tmp & DTLN; |
| dev->act_len += rcv_len; |
| |
| r8a66597_mdfy(r8a66597, PID_NAK, PID, DCPCTR); |
| |
| if (buffer) { |
| if (rcv_len == 0) |
| r8a66597_write(r8a66597, BCLR, DCPCTR); |
| else |
| r8a66597_read_fifo(r8a66597, CFIFO, buffer, rcv_len); |
| } |
| |
| return 0; |
| } |
| |
| static int send_status_packet(struct r8a66597 *r8a66597, |
| unsigned long pipe) |
| { |
| r8a66597_bset(r8a66597, SQSET, DCPCTR); |
| r8a66597_mdfy(r8a66597, PID_NAK, PID, DCPCTR); |
| |
| if (usb_pipein(pipe)) { |
| r8a66597_bset(r8a66597, R8A66597_DIR, DCPCFG); |
| r8a66597_mdfy(r8a66597, ISEL, ISEL | CURPIPE, CFIFOSEL); |
| r8a66597_reg_wait(r8a66597, CFIFOSEL, CURPIPE, 0); |
| r8a66597_write(r8a66597, ~BEMP0, BEMPSTS); |
| r8a66597_write(r8a66597, BCLR | BVAL, CFIFOCTR); |
| } else { |
| r8a66597_bclr(r8a66597, R8A66597_DIR, DCPCFG); |
| r8a66597_mdfy(r8a66597, 0, ISEL | CURPIPE, CFIFOSEL); |
| r8a66597_reg_wait(r8a66597, CFIFOSEL, CURPIPE, 0); |
| r8a66597_write(r8a66597, BCLR, CFIFOCTR); |
| } |
| r8a66597_mdfy(r8a66597, PID_BUF, PID, DCPCTR); |
| |
| while (!(r8a66597_read(r8a66597, BEMPSTS) & 0x0001)) |
| if (ctrlc()) |
| return -1; |
| |
| return 0; |
| } |
| |
| static void r8a66597_check_syssts(struct r8a66597 *r8a66597, int port) |
| { |
| int count = R8A66597_MAX_SAMPLING; |
| unsigned short syssts, old_syssts; |
| |
| R8A66597_DPRINT("%s\n", __func__); |
| |
| old_syssts = r8a66597_read(r8a66597, get_syssts_reg(port) & LNST); |
| while (count > 0) { |
| mdelay(R8A66597_RH_POLL_TIME); |
| |
| syssts = r8a66597_read(r8a66597, get_syssts_reg(port) & LNST); |
| if (syssts == old_syssts) { |
| count--; |
| } else { |
| count = R8A66597_MAX_SAMPLING; |
| old_syssts = syssts; |
| } |
| } |
| } |
| |
| static void r8a66597_bus_reset(struct r8a66597 *r8a66597, int port) |
| { |
| mdelay(10); |
| r8a66597_mdfy(r8a66597, USBRST, USBRST | UACT, get_dvstctr_reg(port)); |
| mdelay(50); |
| r8a66597_mdfy(r8a66597, UACT, USBRST | UACT, get_dvstctr_reg(port)); |
| mdelay(50); |
| } |
| |
| static int check_usb_device_connecting(struct r8a66597 *r8a66597) |
| { |
| int timeout = 10000; /* 100usec * 10000 = 1sec */ |
| int i; |
| |
| for (i = 0; i < 5; i++) { |
| /* check a usb cable connect */ |
| while (!(r8a66597_read(r8a66597, INTSTS1) & ATTCH)) { |
| if (timeout-- < 0) { |
| printf("%s timeout.\n", __func__); |
| return -1; |
| } |
| udelay(100); |
| } |
| |
| /* check a data line */ |
| r8a66597_check_syssts(r8a66597, 0); |
| |
| r8a66597_bus_reset(r8a66597, 0); |
| r8a66597->speed = get_rh_usb_speed(r8a66597, 0); |
| |
| if (!(r8a66597_read(r8a66597, INTSTS1) & DTCH)) { |
| r8a66597->port_change = USB_PORT_STAT_C_CONNECTION; |
| r8a66597->port_status = USB_PORT_STAT_CONNECTION | |
| USB_PORT_STAT_ENABLE; |
| return 0; /* success */ |
| } |
| |
| R8A66597_DPRINT("USB device has detached. retry = %d\n", i); |
| r8a66597_write(r8a66597, ~DTCH, INTSTS1); |
| } |
| |
| return -1; /* fail */ |
| } |
| |
| /* Virtual Root Hub */ |
| |
| #include <usbroothubdes.h> |
| |
| static int r8a66597_submit_rh_msg(struct udevice *udev, struct usb_device *dev, |
| unsigned long pipe, void *buffer, |
| int transfer_len, struct devrequest *cmd) |
| { |
| struct r8a66597 *r8a66597 = dev_get_priv(udev); |
| int leni = transfer_len; |
| int len = 0; |
| int stat = 0; |
| __u16 bmRType_bReq; |
| __u16 wValue; |
| __u16 wLength; |
| unsigned char data[32]; |
| |
| R8A66597_DPRINT("%s\n", __func__); |
| |
| if (usb_pipeint(pipe)) { |
| printf("Root-Hub submit IRQ: NOT implemented"); |
| return 0; |
| } |
| |
| bmRType_bReq = cmd->requesttype | (cmd->request << 8); |
| wValue = cpu_to_le16 (cmd->value); |
| wLength = cpu_to_le16 (cmd->length); |
| |
| switch (bmRType_bReq) { |
| case RH_GET_STATUS: |
| *(__u16 *)buffer = cpu_to_le16(1); |
| len = 2; |
| break; |
| case RH_GET_STATUS | RH_INTERFACE: |
| *(__u16 *)buffer = cpu_to_le16(0); |
| len = 2; |
| break; |
| case RH_GET_STATUS | RH_ENDPOINT: |
| *(__u16 *)buffer = cpu_to_le16(0); |
| len = 2; |
| break; |
| case RH_GET_STATUS | RH_CLASS: |
| *(__u32 *)buffer = cpu_to_le32(0); |
| len = 4; |
| break; |
| case RH_GET_STATUS | RH_OTHER | RH_CLASS: |
| *(__u32 *)buffer = cpu_to_le32(r8a66597->port_status | |
| (r8a66597->port_change << 16)); |
| len = 4; |
| break; |
| case RH_CLEAR_FEATURE | RH_ENDPOINT: |
| case RH_CLEAR_FEATURE | RH_CLASS: |
| break; |
| |
| case RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS: |
| switch (wValue) { |
| case RH_C_PORT_CONNECTION: |
| r8a66597->port_change &= ~USB_PORT_STAT_C_CONNECTION; |
| break; |
| } |
| break; |
| |
| case RH_SET_FEATURE | RH_OTHER | RH_CLASS: |
| switch (wValue) { |
| case (RH_PORT_SUSPEND): |
| break; |
| case (RH_PORT_RESET): |
| r8a66597_bus_reset(r8a66597, 0); |
| break; |
| case (RH_PORT_POWER): |
| break; |
| case (RH_PORT_ENABLE): |
| break; |
| } |
| break; |
| case RH_SET_ADDRESS: |
| r8a66597->rh_devnum = wValue; |
| break; |
| case RH_GET_DESCRIPTOR: |
| switch ((wValue & 0xff00) >> 8) { |
| case (0x01): /* device descriptor */ |
| len = min_t(unsigned int, |
| leni, |
| min_t(unsigned int, |
| sizeof(root_hub_dev_des), |
| wLength)); |
| memcpy(buffer, root_hub_dev_des, len); |
| break; |
| case (0x02): /* configuration descriptor */ |
| len = min_t(unsigned int, |
| leni, |
| min_t(unsigned int, |
| sizeof(root_hub_config_des), |
| wLength)); |
| memcpy(buffer, root_hub_config_des, len); |
| break; |
| case (0x03): /* string descriptors */ |
| if (wValue == 0x0300) { |
| len = min_t(unsigned int, |
| leni, |
| min_t(unsigned int, |
| sizeof(root_hub_str_index0), |
| wLength)); |
| memcpy(buffer, root_hub_str_index0, len); |
| } |
| if (wValue == 0x0301) { |
| len = min_t(unsigned int, |
| leni, |
| min_t(unsigned int, |
| sizeof(root_hub_str_index1), |
| wLength)); |
| memcpy(buffer, root_hub_str_index1, len); |
| } |
| break; |
| default: |
| stat = USB_ST_STALLED; |
| } |
| break; |
| |
| case RH_GET_DESCRIPTOR | RH_CLASS: |
| { |
| __u32 temp = 0x00000001; |
| |
| data[0] = 9; /* min length; */ |
| data[1] = 0x29; |
| data[2] = temp & RH_A_NDP; |
| data[3] = 0; |
| if (temp & RH_A_PSM) |
| data[3] |= 0x1; |
| if (temp & RH_A_NOCP) |
| data[3] |= 0x10; |
| else if (temp & RH_A_OCPM) |
| data[3] |= 0x8; |
| |
| /* corresponds to data[4-7] */ |
| data[5] = (temp & RH_A_POTPGT) >> 24; |
| data[7] = temp & RH_B_DR; |
| if (data[2] < 7) { |
| data[8] = 0xff; |
| } else { |
| data[0] += 2; |
| data[8] = (temp & RH_B_DR) >> 8; |
| data[9] = 0xff; |
| data[10] = 0xff; |
| } |
| |
| len = min_t(unsigned int, leni, |
| min_t(unsigned int, data[0], wLength)); |
| memcpy(buffer, data, len); |
| break; |
| } |
| |
| case RH_GET_CONFIGURATION: |
| *(__u8 *)buffer = 0x01; |
| len = 1; |
| break; |
| case RH_SET_CONFIGURATION: |
| break; |
| default: |
| R8A66597_DPRINT("unsupported root hub command"); |
| stat = USB_ST_STALLED; |
| } |
| |
| mdelay(1); |
| |
| len = min_t(int, len, leni); |
| |
| dev->act_len = len; |
| dev->status = stat; |
| |
| return stat; |
| } |
| |
| static int r8a66597_submit_control_msg(struct udevice *udev, |
| struct usb_device *dev, |
| unsigned long pipe, void *buffer, |
| int length, struct devrequest *setup) |
| { |
| struct r8a66597 *r8a66597 = dev_get_priv(udev); |
| u16 r8a66597_address = setup->request == USB_REQ_SET_ADDRESS ? |
| 0 : dev->devnum; |
| |
| debug("%s: dev='%s', udev=%p, udev->dev='%s', portnr=%d\n", __func__, |
| udev->name, dev, dev->dev->name, dev->portnr); |
| |
| R8A66597_DPRINT("%s\n", __func__); |
| if (usb_pipedevice(pipe) == r8a66597->rh_devnum) |
| return r8a66597_submit_rh_msg(udev, dev, pipe, buffer, |
| length, setup); |
| |
| R8A66597_DPRINT("%s: setup\n", __func__); |
| set_devadd(r8a66597, r8a66597_address, dev, 0); |
| |
| if (send_setup_packet(r8a66597, dev, setup) < 0) { |
| printf("setup packet send error\n"); |
| return -1; |
| } |
| |
| dev->act_len = 0; |
| if (usb_pipein(pipe)) |
| if (receive_control_packet(r8a66597, dev, buffer, |
| length) < 0) |
| return -1; |
| |
| if (send_status_packet(r8a66597, pipe) < 0) |
| return -1; |
| |
| dev->status = 0; |
| |
| return 0; |
| } |
| |
| static int r8a66597_submit_bulk_msg(struct udevice *udev, |
| struct usb_device *dev, unsigned long pipe, |
| void *buffer, int length) |
| { |
| struct r8a66597 *r8a66597 = dev_get_priv(udev); |
| int ret = 0; |
| |
| debug("%s: dev='%s', udev=%p\n", __func__, udev->name, dev); |
| |
| R8A66597_DPRINT("%s\n", __func__); |
| R8A66597_DPRINT("pipe = %08x, buffer = %p, len = %d, devnum = %d\n", |
| pipe, buffer, length, dev->devnum); |
| |
| set_devadd(r8a66597, dev->devnum, dev, 0); |
| |
| pipe_buffer_setting(r8a66597, dev, pipe); |
| |
| dev->act_len = 0; |
| while (dev->act_len < length && ret == 0) { |
| if (ctrlc()) |
| return -1; |
| |
| if (usb_pipein(pipe)) |
| ret = receive_bulk_packet(r8a66597, dev, pipe, buffer, |
| length); |
| else |
| ret = send_bulk_packet(r8a66597, dev, pipe, buffer, |
| length); |
| } |
| |
| if (ret == 0) |
| dev->status = 0; |
| |
| return ret; |
| } |
| |
| static int r8a66597_usb_of_to_plat(struct udevice *dev) |
| { |
| struct r8a66597 *priv = dev_get_priv(dev); |
| fdt_addr_t addr; |
| |
| addr = dev_read_addr(dev); |
| if (addr == FDT_ADDR_T_NONE) |
| return -EINVAL; |
| priv->reg = addr; |
| |
| return 0; |
| } |
| |
| static int r8a66597_usb_probe(struct udevice *dev) |
| { |
| struct r8a66597 *priv = dev_get_priv(dev); |
| struct usb_bus_priv *bus_priv = dev_get_uclass_priv(dev); |
| int ret; |
| |
| bus_priv->desc_before_addr = true; |
| |
| if (CONFIG_IS_ENABLED(DM_REGULATOR)) { |
| ret = device_get_supply_regulator(dev, "vbus-supply", |
| &priv->vbus_supply); |
| if (ret) { |
| dev_err(dev, |
| "can't get VBUS supply\n"); |
| return ret; |
| } |
| |
| ret = regulator_set_enable(priv->vbus_supply, true); |
| if (ret) { |
| dev_err(dev, |
| "can't enable VBUS supply\n"); |
| return ret; |
| } |
| } |
| |
| disable_controller(priv); |
| mdelay(100); |
| |
| enable_controller(priv); |
| r8a66597_port_power(priv, 0, 1); |
| |
| /* check usb device */ |
| check_usb_device_connecting(priv); |
| |
| mdelay(50); |
| |
| return 0; |
| } |
| |
| static int r8a66597_usb_remove(struct udevice *dev) |
| { |
| struct r8a66597 *priv = dev_get_priv(dev); |
| int ret; |
| |
| disable_controller(priv); |
| |
| if (CONFIG_IS_ENABLED(DM_REGULATOR)) { |
| ret = regulator_set_enable(priv->vbus_supply, false); |
| if (ret) { |
| dev_err(dev, |
| "can't disable VBUS supply\n"); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| struct dm_usb_ops r8a66597_usb_ops = { |
| .control = r8a66597_submit_control_msg, |
| .bulk = r8a66597_submit_bulk_msg, |
| }; |
| |
| static const struct udevice_id r8a66597_usb_ids[] = { |
| { .compatible = "renesas,rza1-usbhs" }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(usb_r8a66597) = { |
| .name = "r8a66597_usb", |
| .id = UCLASS_USB, |
| .of_match = r8a66597_usb_ids, |
| .of_to_plat = r8a66597_usb_of_to_plat, |
| .probe = r8a66597_usb_probe, |
| .remove = r8a66597_usb_remove, |
| .ops = &r8a66597_usb_ops, |
| .priv_auto = sizeof(struct r8a66597), |
| .flags = DM_FLAG_ALLOC_PRIV_DMA, |
| }; |