blob: c0bf3673028df2736d4d43d2829933bd4c90b12a [file] [log] [blame]
/*
* (C) Copyright 2000-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC860 1 /* This is a MPC860 CPU */
#define CONFIG_IP860 1 /* ...on a IP860 board */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" \
"\0load=tftp \"/tftpboot/u-boot.bin\"\0update=protect off 1:0;era 1:0;cp.b 100000 10000000 ${filesize}\0"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND \
"bootp; " \
"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
"bootm"
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#undef CONFIG_WATCHDOG /* watchdog disabled */
/* enable I2C and select the hardware/software driver */
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
/*
* Software (bit-bang) I2C driver configuration
*/
#define PB_SCL 0x00000020 /* PB 26 */
#define PB_SDA 0x00000010 /* PB 27 */
#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
else immr->im_cpm.cp_pbdat &= ~PB_SDA
#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
else immr->im_cpm.cp_pbdat &= ~PB_SCL
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
# define CFG_I2C_SPEED 50000
# define CFG_I2C_SLAVE 0xFE
# define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C16 */
# define CFG_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_BEDBUG
#define CONFIG_CMD_I2C
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_NFS
#define CONFIG_CMD_SNTP
/*
* BOOTP options
*/
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */
#define CFG_LOAD_ADDR 0x00100000 /* default load address */
#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
#define CFG_IMMR 0xF1000000 /* Non-standard value!! */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR CFG_IMMR
#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0x10000000
#ifdef DEBUG
#define CFG_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
#else
#if 0 /* need more space for I2C tests */
#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
#else
#define CFG_MONITOR_LEN (256 << 10)
#endif
#endif
#define CFG_MONITOR_BASE CFG_FLASH_BASE
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 124 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#undef CONFIG_ENV_IS_IN_FLASH
#undef CONFIG_ENV_IS_IN_NVRAM
#undef CONFIG_ENV_IS_IN_NVRAM
#undef DEBUG_I2C
#define CONFIG_ENV_IS_IN_EEPROM
#ifdef CONFIG_ENV_IS_IN_NVRAM
#define CONFIG_ENV_ADDR 0x20000000 /* use SRAM */
#define CONFIG_ENV_SIZE (16<<10) /* use 16 kB */
#endif /* CONFIG_ENV_IS_IN_NVRAM */
#ifdef CONFIG_ENV_IS_IN_EEPROM
#define CONFIG_ENV_OFFSET 512 /* Leave 512 bytes free for other data */
#define CONFIG_ENV_SIZE 1536 /* Use remaining space */
#endif /* CONFIG_ENV_IS_IN_EEPROM */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
* +0x0004
*/
#if defined(CONFIG_WATCHDOG)
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 11-6
*-----------------------------------------------------------------------
* +0x0000 => 0x80600800
*/
#define CFG_SIUMCR (SIUMCR_EARB | SIUMCR_EARP0 | \
SIUMCR_DBGC11 | SIUMCR_MLRC10)
/*-----------------------------------------------------------------------
* Clock Setting - get clock frequency from Board Revision Register
*-----------------------------------------------------------------------
*/
#ifndef __ASSEMBLY__
extern unsigned long ip860_get_clk_freq (void);
#endif
#define CONFIG_8xx_GCLK_FREQ ip860_get_clk_freq()
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
* +0x0200 => 0x00C2
*/
#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
* +0x0240 => 0x0082
*/
#define CFG_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
*-----------------------------------------------------------------------
* Reset PLL lock status sticky bit, timer expired status bit and timer
* interrupt status bit, set PLL multiplication factor !
*/
/* +0x0286 => was: 0x0000D000 */
#define CFG_PLPRCR \
( PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | \
/*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \
PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \
)
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
*-----------------------------------------------------------------------
* Set clock output, timebase and RTC source and divider,
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF11
#define CFG_SCCR (SCCR_COM00 | SCCR_TBS | \
SCCR_RTDIV | SCCR_RTSEL | \
/*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \
SCCR_EBDF00 | SCCR_DFSYNC00 | \
SCCR_DFBRG00 | SCCR_DFNL000 | \
SCCR_DFNH000)
/*-----------------------------------------------------------------------
* RTCSC - Real-Time Clock Status and Control Register 11-27
*-----------------------------------------------------------------------
*/
/* +0x0220 => 0x00C3 */
#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
/*-----------------------------------------------------------------------
* RCCR - RISC Controller Configuration Register 19-4
*-----------------------------------------------------------------------
*/
/* +0x09C4 => TIMEP=1 */
#define CFG_RCCR 0x0100
/*-----------------------------------------------------------------------
* RMDS - RISC Microcode Development Support Control Register
*-----------------------------------------------------------------------
*/
#define CFG_RMDS 0
/*-----------------------------------------------------------------------
* DER - Debug Event Register
*-----------------------------------------------------------------------
*
*/
#define CFG_DER 0
/*
* Init Memory Controller:
*/
/*
* MAMR settings for SDRAM - 16-14
* => 0xC3804114
*/
/* periodic timer for refresh */
#define CFG_MAMR_PTA 0xC3
#define CFG_MAMR ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
/*
* BR1 and OR1 (FLASH)
*/
#define FLASH_BASE 0x10000000 /* FLASH bank #0 */
/* used to re-map FLASH
* restrict access enough to keep SRAM working (if any)
* but not too much to meddle with FLASH accesses
*/
/* allow for max 8 MB of Flash */
#define CFG_REMAP_OR_AM 0xFF800000 /* OR addr mask */
#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */
#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | OR_SCY_6_CLK)
#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
/* 16 bit, bank valid */
#define CFG_BR0_PRELIM ((FLASH_BASE & BR_BA_MSK) | BR_PS_32 | BR_V )
#define CFG_OR1_PRELIM CFG_OR0_PRELIM
#define CFG_BR1_PRELIM CFG_BR0_PRELIM
/*
* BR2/OR2 - SDRAM
*/
#define SDRAM_BASE 0x00000000 /* SDRAM bank */
#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */
#define SDRAM_TIMING 0x00000A00 /* SDRAM-Timing */
#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */
#define CFG_OR2 (SDRAM_PRELIM_OR_AM | SDRAM_TIMING )
#define CFG_BR2 ((SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V )
/*
* BR3/OR3 - SRAM (16 bit)
*/
#define SRAM_BASE 0x20000000
#define CFG_OR3 0xFFF00130 /* BI/SCY = 5/TRLX (internal) */
#define CFG_BR3 ((SRAM_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
#define SRAM_SIZE (1 + (~(CFG_OR3 & BR_BA_MSK)))
#define CFG_OR3_PRELIM CFG_OR3 /* Make sure to map early */
#define CFG_BR3_PRELIM CFG_BR3 /* in case it's used for ENV */
/*
* BR4/OR4 - Board Control & Status (8 bit)
*/
#define BCSR_BASE 0xFC000000
#define CFG_OR4 0xFFFF0120 /* BI (internal) */
#define CFG_BR4 ((BCSR_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
/*
* BR5/OR5 - IP Slot A/B (16 bit)
*/
#define IP_SLOT_BASE 0x40000000
#define CFG_OR5 0xFE00010C /* SETA/TRLX/BI/ SCY=0 (external) */
#define CFG_BR5 ((IP_SLOT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
/*
* BR6/OR6 - VME STD (16 bit)
*/
#define VME_STD_BASE 0xFE000000
#define CFG_OR6 0xFF00010C /* SETA/TRLX/BI/SCY=0 (external) */
#define CFG_BR6 ((VME_STD_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
/*
* BR7/OR7 - SHORT I/O + RTC + IACK (16 bit)
*/
#define VME_SHORT_BASE 0xFF000000
#define CFG_OR7 0xFF00010C /* SETA/TRLX/BI/ SCY=0 (external) */
#define CFG_BR7 ((VME_SHORT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
/*-----------------------------------------------------------------------
* Board Control and Status Region:
*-----------------------------------------------------------------------
*/
#ifndef __ASSEMBLY__
typedef struct ip860_bcsr_s {
unsigned char shmem_addr; /* +00 shared memory address register */
unsigned char reserved0;
unsigned char mbox_addr; /* +02 mailbox address register */
unsigned char reserved1;
unsigned char vme_int_mask; /* +04 VME Bus interrupt mask register */
unsigned char reserved2;
unsigned char vme_int_pend; /* +06 VME interrupt pending register */
unsigned char reserved3;
unsigned char bd_int_mask; /* +08 board interrupt mask register */
unsigned char reserved4;
unsigned char bd_int_pend; /* +0A board interrupt pending register */
unsigned char reserved5;
unsigned char bd_ctrl; /* +0C board control register */
unsigned char reserved6;
unsigned char bd_status; /* +0E board status register */
unsigned char reserved7;
unsigned char vme_irq; /* +10 VME interrupt request register */
unsigned char reserved8;
unsigned char vme_ivec; /* +12 VME interrupt vector register */
unsigned char reserved9;
unsigned char cli_mbox; /* +14 clear mailbox irq */
unsigned char reservedA;
unsigned char rtc; /* +16 RTC control register */
unsigned char reservedB;
unsigned char mbox_data; /* +18 mailbox read/write register */
unsigned char reservedC;
unsigned char wd_trigger; /* +1A Watchdog trigger register */
unsigned char reservedD;
unsigned char rmw_req; /* +1C RMW request register */
unsigned char reservedE;
unsigned char bd_rev; /* +1E Board Revision register */
} ip860_bcsr_t;
#endif /* __ASSEMBLY__ */
/*-----------------------------------------------------------------------
* Board Control Register: bd_ctrl (Offset 0x0C)
*-----------------------------------------------------------------------
*/
#define BD_CTRL_IPLSE 0x80 /* IP Slot Long Select Enable */
#define BD_CTRL_WDOGE 0x40 /* Watchdog Enable */
#define BD_CTRL_FLWE 0x20 /* Flash Write Enable */
#define BD_CTRL_RWDN 0x10 /* VMEBus Requester Release When Done Enable */
/*-----------------------------------------------------------------------
*
*-----------------------------------------------------------------------
*
*/
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#endif /* __CONFIG_H */