blob: 5b3b56042613585da16e4efe3c234dc5db7f7496 [file] [log] [blame]
/*
* Copyright 2007,2009-2011 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <command.h>
#include <pci.h>
#include <asm/processor.h>
#include <asm/immap_86xx.h>
#include <asm/fsl_pci.h>
#include <asm/fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <i2c.h>
#include <asm/io.h>
#include <libfdt.h>
#include <fdt_support.h>
#include <spd_sdram.h>
#include <netdev.h>
void sdram_init(void);
phys_size_t fixed_sdram(void);
int mpc8610hpcd_diu_init(void);
/* called before any console output */
int board_early_init_f(void)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile ccsr_gur_t *gur = &immap->im_gur;
gur->gpiocr |= 0x88aa5500; /* DIU16, IR1, UART0, UART2 */
return 0;
}
int misc_init_r(void)
{
u8 tmp_val, version;
u8 *pixis_base = (u8 *)PIXIS_BASE;
/*Do not use 8259PIC*/
tmp_val = in_8(pixis_base + PIXIS_BRDCFG0);
out_8(pixis_base + PIXIS_BRDCFG0, tmp_val | 0x80);
/*For FPGA V7 or higher, set the IRQMAPSEL to 0 to use MAP0 interrupt*/
version = in_8(pixis_base + PIXIS_PVER);
if(version >= 0x07) {
tmp_val = in_8(pixis_base + PIXIS_BRDCFG0);
out_8(pixis_base + PIXIS_BRDCFG0, tmp_val & 0xbf);
}
/* Using this for DIU init before the driver in linux takes over
* Enable the TFP410 Encoder (I2C address 0x38)
*/
tmp_val = 0xBF;
i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
/* Verify if enabled */
tmp_val = 0;
i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
debug("DVI Encoder Read: 0x%02x\n", tmp_val);
tmp_val = 0x10;
i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
/* Verify if enabled */
tmp_val = 0;
i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
debug("DVI Encoder Read: 0x%02x\n", tmp_val);
return 0;
}
int checkboard(void)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile ccsr_local_mcm_t *mcm = &immap->im_local_mcm;
u8 *pixis_base = (u8 *)PIXIS_BASE;
printf ("Board: MPC8610HPCD, Sys ID: 0x%02x, "
"Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER),
in_8(pixis_base + PIXIS_PVER));
/*
* The MPC8610 HPCD workbook says that LBMAP=11 is the "normal" boot
* bank and LBMAP=00 is the alternate bank. However, the pixis
* altbank code can only set bits, not clear them, so we treat 00 as
* the normal bank and 11 as the alternate.
*/
switch (in_8(pixis_base + PIXIS_VBOOT) & 0xC0) {
case 0:
puts("vBank: Standard\n");
break;
case 0x40:
puts("Promjet\n");
break;
case 0x80:
puts("NAND\n");
break;
case 0xC0:
puts("vBank: Alternate\n");
break;
}
mcm->abcr |= 0x00010000; /* 0 */
mcm->hpmr3 = 0x80000008; /* 4c */
mcm->hpmr0 = 0;
mcm->hpmr1 = 0;
mcm->hpmr2 = 0;
mcm->hpmr4 = 0;
mcm->hpmr5 = 0;
return 0;
}
phys_size_t
initdram(int board_type)
{
phys_size_t dram_size = 0;
#if defined(CONFIG_SPD_EEPROM)
dram_size = fsl_ddr_sdram();
#else
dram_size = fixed_sdram();
#endif
setup_ddr_bat(dram_size);
debug(" DDR: ");
return dram_size;
}
#if !defined(CONFIG_SPD_EEPROM)
/*
* Fixed sdram init -- doesn't use serial presence detect.
*/
phys_size_t fixed_sdram(void)
{
#if !defined(CONFIG_SYS_RAMBOOT)
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile ccsr_ddr_t *ddr = &immap->im_ddr1;
uint d_init;
ddr->cs0_bnds = 0x0000001f;
ddr->cs0_config = 0x80010202;
ddr->timing_cfg_3 = 0x00000000;
ddr->timing_cfg_0 = 0x00260802;
ddr->timing_cfg_1 = 0x3935d322;
ddr->timing_cfg_2 = 0x14904cc8;
ddr->sdram_mode = 0x00480432;
ddr->sdram_mode_2 = 0x00000000;
ddr->sdram_interval = 0x06180fff; /* 0x06180100; */
ddr->sdram_data_init = 0xDEADBEEF;
ddr->sdram_clk_cntl = 0x03800000;
ddr->sdram_cfg_2 = 0x04400010;
#if defined(CONFIG_DDR_ECC)
ddr->err_int_en = 0x0000000d;
ddr->err_disable = 0x00000000;
ddr->err_sbe = 0x00010000;
#endif
asm("sync;isync");
udelay(500);
ddr->sdram_cfg = 0xc3000000; /* 0xe3008000;*/
#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
d_init = 1;
debug("DDR - 1st controller: memory initializing\n");
/*
* Poll until memory is initialized.
* 512 Meg at 400 might hit this 200 times or so.
*/
while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0)
udelay(1000);
debug("DDR: memory initialized\n\n");
asm("sync; isync");
udelay(500);
#endif
return 512 * 1024 * 1024;
#endif
return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
}
#endif
#if defined(CONFIG_PCI)
/*
* Initialize PCI Devices, report devices found.
*/
#ifndef CONFIG_PCI_PNP
static struct pci_config_table pci_fsl86xxads_config_table[] = {
{PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
PCI_IDSEL_NUMBER, PCI_ANY_ID,
pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
PCI_ENET0_MEMADDR,
PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER} },
{}
};
#endif
static struct pci_controller pci1_hose;
#endif /* CONFIG_PCI */
void pci_init_board(void)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_CCSRBAR;
volatile ccsr_gur_t *gur = &immap->im_gur;
struct fsl_pci_info pci_info;
u32 devdisr, pordevsr;
int first_free_busno;
int pci_agent;
devdisr = in_be32(&gur->devdisr);
pordevsr = in_be32(&gur->pordevsr);
first_free_busno = fsl_pcie_init_board(0);
#ifdef CONFIG_PCI1
if (!(devdisr & MPC86xx_DEVDISR_PCI1)) {
SET_STD_PCI_INFO(pci_info, 1);
set_next_law(pci_info.mem_phys,
law_size_bits(pci_info.mem_size), pci_info.law);
set_next_law(pci_info.io_phys,
law_size_bits(pci_info.io_size), pci_info.law);
pci_agent = fsl_setup_hose(&pci1_hose, pci_info.regs);
printf("PCI: connected to PCI slots as %s" \
" (base address %lx)\n",
pci_agent ? "Agent" : "Host",
pci_info.regs);
#ifndef CONFIG_PCI_PNP
pci1_hose.config_table = pci_mpc86xxcts_config_table;
#endif
first_free_busno = fsl_pci_init_port(&pci_info,
&pci1_hose, first_free_busno);
} else {
printf("PCI: disabled\n");
}
puts("\n");
#else
setbits_be32(&gur->devdisr, MPC86xx_DEVDISR_PCI1); /* disable */
#endif
fsl_pcie_init_board(first_free_busno);
}
#if defined(CONFIG_OF_BOARD_SETUP)
void
ft_board_setup(void *blob, bd_t *bd)
{
ft_cpu_setup(blob, bd);
FT_FSL_PCI_SETUP;
}
#endif
/*
* get_board_sys_clk
* Reads the FPGA on board for CONFIG_SYS_CLK_FREQ
*/
unsigned long
get_board_sys_clk(ulong dummy)
{
u8 i;
ulong val = 0;
u8 *pixis_base = (u8 *)PIXIS_BASE;
i = in_8(pixis_base + PIXIS_SPD);
i &= 0x07;
switch (i) {
case 0:
val = 33333000;
break;
case 1:
val = 39999600;
break;
case 2:
val = 49999500;
break;
case 3:
val = 66666000;
break;
case 4:
val = 83332500;
break;
case 5:
val = 99999000;
break;
case 6:
val = 133332000;
break;
case 7:
val = 166665000;
break;
}
return val;
}
int board_eth_init(bd_t *bis)
{
return pci_eth_init(bis);
}
void board_reset(void)
{
u8 *pixis_base = (u8 *)PIXIS_BASE;
out_8(pixis_base + PIXIS_RST, 0);
while (1)
;
}