blob: 17560c8dbae52ba8c028d7b76aa378d7736280e9 [file] [log] [blame]
/*
* Copyright (C) 2006 Freescale Semiconductor, Inc.
* Dave Liu <daveliu@freescale.com>
*
* Copyright (C) 2007 Logic Product Development, Inc.
* Peter Barada <peterb@logicpd.com>
*
* Copyright (C) 2007 MontaVista Software, Inc.
* Anton Vorontsov <avorontsov@ru.mvista.com>
*
* (C) Copyright 2008 - 2010
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*/
#include <common.h>
#include <ioports.h>
#include <mpc83xx.h>
#include <i2c.h>
#include <miiphy.h>
#include <asm/io.h>
#include <asm/mmu.h>
#include <asm/processor.h>
#include <pci.h>
#include <libfdt.h>
#include "../common/common.h"
const qe_iop_conf_t qe_iop_conf_tab[] = {
/* port pin dir open_drain assign */
#if defined(CONFIG_KMETER1)
/* MDIO */
{0, 1, 3, 0, 2}, /* MDIO */
{0, 2, 1, 0, 1}, /* MDC */
/* UCC4 - UEC */
{1, 14, 1, 0, 1}, /* TxD0 */
{1, 15, 1, 0, 1}, /* TxD1 */
{1, 20, 2, 0, 1}, /* RxD0 */
{1, 21, 2, 0, 1}, /* RxD1 */
{1, 18, 1, 0, 1}, /* TX_EN */
{1, 26, 2, 0, 1}, /* RX_DV */
{1, 27, 2, 0, 1}, /* RX_ER */
{1, 24, 2, 0, 1}, /* COL */
{1, 25, 2, 0, 1}, /* CRS */
{2, 15, 2, 0, 1}, /* TX_CLK - CLK16 */
{2, 16, 2, 0, 1}, /* RX_CLK - CLK17 */
/* DUART - UART2 */
{5, 0, 1, 0, 2}, /* UART2_SOUT */
{5, 2, 1, 0, 1}, /* UART2_RTS */
{5, 3, 2, 0, 2}, /* UART2_SIN */
{5, 1, 2, 0, 3}, /* UART2_CTS */
#else
/* Local Bus */
{0, 16, 1, 0, 3}, /* LA00 */
{0, 17, 1, 0, 3}, /* LA01 */
{0, 18, 1, 0, 3}, /* LA02 */
{0, 19, 1, 0, 3}, /* LA03 */
{0, 20, 1, 0, 3}, /* LA04 */
{0, 21, 1, 0, 3}, /* LA05 */
{0, 22, 1, 0, 3}, /* LA06 */
{0, 23, 1, 0, 3}, /* LA07 */
{0, 24, 1, 0, 3}, /* LA08 */
{0, 25, 1, 0, 3}, /* LA09 */
{0, 26, 1, 0, 3}, /* LA10 */
{0, 27, 1, 0, 3}, /* LA11 */
{0, 28, 1, 0, 3}, /* LA12 */
{0, 29, 1, 0, 3}, /* LA13 */
{0, 30, 1, 0, 3}, /* LA14 */
{0, 31, 1, 0, 3}, /* LA15 */
/* MDIO */
{3, 4, 3, 0, 2}, /* MDIO */
{3, 5, 1, 0, 2}, /* MDC */
/* UCC4 - UEC */
{1, 18, 1, 0, 1}, /* TxD0 */
{1, 19, 1, 0, 1}, /* TxD1 */
{1, 22, 2, 0, 1}, /* RxD0 */
{1, 23, 2, 0, 1}, /* RxD1 */
{1, 26, 2, 0, 1}, /* RxER */
{1, 28, 2, 0, 1}, /* Rx_DV */
{1, 30, 1, 0, 1}, /* TxEN */
{1, 31, 2, 0, 1}, /* CRS */
{3, 10, 2, 0, 3}, /* TxCLK->CLK17 */
#endif
/* END of table */
{0, 0, 0, 0, QE_IOP_TAB_END},
};
static int board_init_i2c_busses(void)
{
I2C_MUX_DEVICE *dev = NULL;
uchar *buf;
/* Set up the Bus for the DTTs */
buf = (unsigned char *) getenv("dtt_bus");
if (buf != NULL)
dev = i2c_mux_ident_muxstring(buf);
if (dev == NULL) {
printf("Error couldn't add Bus for DTT\n");
printf("please setup dtt_bus to where your\n");
printf("DTT is found.\n");
}
return 0;
}
#if defined(CONFIG_SUVD3)
const uint upma_table[] = {
0x1ffedc00, 0x0ffcdc80, 0x0ffcdc80, 0x0ffcdc04, /* Words 0 to 3 */
0x0ffcdc00, 0xffffcc00, 0xffffcc01, 0xfffffc01, /* Words 4 to 7 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 8 to 11 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 12 to 15 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 16 to 19 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 20 to 23 */
0x9cfffc00, 0x00fffc80, 0x00fffc80, 0x00fffc00, /* Words 24 to 27 */
0xffffec04, 0xffffec01, 0xfffffc01, 0xfffffc01, /* Words 28 to 31 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 32 to 35 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 36 to 39 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 40 to 43 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 44 to 47 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 48 to 51 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 52 to 55 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 56 to 59 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01 /* Words 60 to 63 */
};
#endif
int board_early_init_r(void)
{
struct km_bec_fpga *base =
(struct km_bec_fpga *)CONFIG_SYS_KMBEC_FPGA_BASE;
#if defined(CONFIG_SUVD3)
immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
fsl_lbc_t *lbc = &immap->im_lbc;
u32 *mxmr = &lbc->mamr;
#endif
#if defined(CONFIG_MPC8360)
unsigned short svid;
/*
* Because of errata in the UCCs, we have to write to the reserved
* registers to slow the clocks down.
*/
svid = SVR_REV(mfspr(SVR));
switch (svid) {
case 0x0020:
/*
* MPC8360ECE.pdf QE_ENET10 table 4:
* IMMR + 0x14A8[4:5] = 11 (clk delay for UCC 2)
* IMMR + 0x14A8[18:19] = 11 (clk delay for UCC 1)
*/
setbits_be32((void *)(CONFIG_SYS_IMMR + 0x14a8), 0x0c003000);
break;
case 0x0021:
/*
* MPC8360ECE.pdf QE_ENET10 table 4:
* IMMR + 0x14AC[24:27] = 1010
*/
clrsetbits_be32((void *)(CONFIG_SYS_IMMR + 0x14ac),
0x00000050, 0x000000a0);
break;
}
#endif
/* enable the PHY on the PIGGY */
setbits_8(&base->pgy_eth, 0x01);
/* enable the Unit LED (green) */
setbits_8(&base->oprth, WRL_BOOT);
#if defined(CONFIG_SUVD3)
/* configure UPMA for APP1 */
upmconfig(UPMA, (uint *) upma_table,
sizeof(upma_table) / sizeof(uint));
out_be32(mxmr, CONFIG_SYS_MAMR);
#endif
return 0;
}
int misc_init_r(void)
{
/* add board specific i2c busses */
board_init_i2c_busses();
return 0;
}
int last_stage_init(void)
{
set_km_env();
return 0;
}
int fixed_sdram(void)
{
immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
u32 msize = 0;
u32 ddr_size;
u32 ddr_size_log2;
out_be32(&im->sysconf.ddrlaw[0].ar, (LAWAR_EN | 0x1e));
out_be32(&im->ddr.csbnds[0].csbnds, CONFIG_SYS_DDR_CS0_BNDS);
out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CNTL);
udelay(200);
out_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
msize = CONFIG_SYS_DDR_SIZE << 20;
disable_addr_trans();
msize = get_ram_size(CONFIG_SYS_DDR_BASE, msize);
enable_addr_trans();
msize /= (1024 * 1024);
if (CONFIG_SYS_DDR_SIZE != msize) {
for (ddr_size = msize << 20, ddr_size_log2 = 0;
(ddr_size > 1);
ddr_size = ddr_size >> 1, ddr_size_log2++)
if (ddr_size & 1)
return -1;
out_be32(&im->sysconf.ddrlaw[0].ar,
(LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE)));
out_be32(&im->ddr.csbnds[0].csbnds,
(((msize / 16) - 1) & 0xff));
}
return msize;
}
phys_size_t initdram(int board_type)
{
immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
u32 msize = 0;
if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im)
return -1;
out_be32(&im->sysconf.ddrlaw[0].bar,
CONFIG_SYS_DDR_BASE & LAWBAR_BAR);
msize = fixed_sdram();
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
/*
* Initialize DDR ECC byte
*/
ddr_enable_ecc(msize * 1024 * 1024);
#endif
/* return total bus SDRAM size(bytes) -- DDR */
return msize * 1024 * 1024;
}
int checkboard(void)
{
puts("Board: Keymile " CONFIG_KM_BOARD_NAME);
if (ethernet_present())
puts(" with PIGGY.");
puts("\n");
return 0;
}
#if defined(CONFIG_OF_BOARD_SETUP)
void ft_board_setup(void *blob, bd_t *bd)
{
ft_cpu_setup(blob, bd);
}
#endif
#if defined(CONFIG_HUSH_INIT_VAR)
int hush_init_var(void)
{
ivm_read_eeprom();
return 0;
}
#endif