| /* |
| * (C) Copyright 2009 |
| * Net Insight <www.netinsight.net> |
| * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net> |
| * |
| * Based on sheevaplug.h: |
| * (C) Copyright 2009 |
| * Marvell Semiconductor <www.marvell.com> |
| * Written-by: Prafulla Wadaskar <prafulla@marvell.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef _CONFIG_OPENRD_H |
| #define _CONFIG_OPENRD_H |
| |
| /* |
| * High Level Configuration Options (easy to change) |
| */ |
| #define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ |
| #define CONFIG_KW88F6281 1 /* SOC Name */ |
| #define CONFIG_MACH_OPENRD_BASE /* Machine type */ |
| #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ |
| #define CONFIG_SYS_THUMB_BUILD |
| |
| /* |
| * Commands configuration |
| */ |
| #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ |
| #define CONFIG_SYS_MVFS |
| #define CONFIG_CMD_ENV |
| #define CONFIG_CMD_NAND |
| #define CONFIG_CMD_IDE |
| |
| /* |
| * mv-common.h should be defined after CMD configs since it used them |
| * to enable certain macros |
| */ |
| #include "mv-common.h" |
| |
| /* |
| * Environment variables configurations |
| */ |
| #ifdef CONFIG_CMD_NAND |
| #define CONFIG_ENV_IS_IN_NAND 1 |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */ |
| #else |
| #define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */ |
| #endif |
| /* |
| * max 4k env size is enough, but in case of nand |
| * it has to be rounded to sector size |
| */ |
| #define CONFIG_ENV_SIZE 0x20000 /* 128k */ |
| #define CONFIG_ENV_ADDR 0x60000 |
| #define CONFIG_ENV_OFFSET 0x60000 /* env starts here */ |
| /* |
| * Environment is right behind U-Boot in flash. Make sure U-Boot |
| * doesn't grow into the environment area. |
| */ |
| #define CONFIG_BOARD_SIZE_LIMIT CONFIG_ENV_OFFSET |
| |
| /* |
| * Default environment variables |
| */ |
| #define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \ |
| "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ |
| "${x_bootcmd_usb}; bootm 0x6400000;" |
| |
| #define MTDIDS_DEFAULT "nand0=nand_mtd" |
| #define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000@0x000000(uboot),"\ |
| "0x400000@0x100000(uImage),"\ |
| "0x1fb00000@0x500000(rootfs)" |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \ |
| "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \ |
| "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \ |
| "x_bootcmd_usb=usb start\0" \ |
| "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \ |
| "mtdids="MTDIDS_DEFAULT"\0" \ |
| "mtdparts="MTDPARTS_DEFAULT"\0" |
| |
| /* |
| * Ethernet Driver configuration |
| */ |
| #ifdef CONFIG_CMD_NET |
| # ifdef CONFIG_BOARD_IS_OPENRD_BASE |
| # define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ |
| # else |
| # define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ |
| # endif |
| # ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE |
| # define CONFIG_PHY_BASE_ADR 0x0 |
| # define PHY_NO "88E1121" |
| # else |
| # define CONFIG_PHY_BASE_ADR 0x8 |
| # define PHY_NO "88E1116" |
| # endif |
| #endif /* CONFIG_CMD_NET */ |
| |
| /* |
| * SATA Driver configuration |
| */ |
| #ifdef CONFIG_MVSATA_IDE |
| #define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET |
| #define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET |
| #endif /*CONFIG_MVSATA_IDE*/ |
| |
| #ifdef CONFIG_CMD_MMC |
| #define CONFIG_GENERIC_MMC |
| #define CONFIG_MVEBU_MMC |
| #define CONFIG_SYS_MMC_BASE KW_SDIO_BASE |
| #endif /* CONFIG_CMD_MMC */ |
| |
| #endif /* _CONFIG_OPENRD_BASE_H */ |