| /* |
| * Copyright (C) 2014 Panasonic Corporation |
| * Copyright (C) 2015 Socionext Inc. |
| * Author: Masahiro Yamada <yamada.masahiro@socionext.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <common.h> |
| #include <linux/types.h> |
| #include <asm/io.h> |
| #include <asm/errno.h> |
| #include <dm/device.h> |
| #include <dm/root.h> |
| #include <i2c.h> |
| #include <fdtdec.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| struct uniphier_i2c_regs { |
| u32 dtrm; /* data transmission */ |
| #define I2C_DTRM_STA (1 << 10) |
| #define I2C_DTRM_STO (1 << 9) |
| #define I2C_DTRM_NACK (1 << 8) |
| #define I2C_DTRM_RD (1 << 0) |
| u32 drec; /* data reception */ |
| #define I2C_DREC_STS (1 << 12) |
| #define I2C_DREC_LRB (1 << 11) |
| #define I2C_DREC_LAB (1 << 9) |
| u32 myad; /* slave address */ |
| u32 clk; /* clock frequency control */ |
| u32 brst; /* bus reset */ |
| #define I2C_BRST_FOEN (1 << 1) |
| #define I2C_BRST_BRST (1 << 0) |
| u32 hold; /* hold time control */ |
| u32 bsts; /* bus status monitor */ |
| u32 noise; /* noise filter control */ |
| u32 setup; /* setup time control */ |
| }; |
| |
| #define IOBUS_FREQ 100000000 |
| |
| struct uniphier_i2c_dev { |
| struct uniphier_i2c_regs __iomem *regs; /* register base */ |
| unsigned long input_clk; /* master clock (Hz) */ |
| unsigned long wait_us; /* wait for every byte transfer (us) */ |
| }; |
| |
| static int uniphier_i2c_probe(struct udevice *dev) |
| { |
| fdt_addr_t addr; |
| fdt_size_t size; |
| struct uniphier_i2c_dev *priv = dev_get_priv(dev); |
| |
| addr = fdtdec_get_addr_size(gd->fdt_blob, dev->of_offset, "reg", &size); |
| |
| priv->regs = map_sysmem(addr, size); |
| |
| if (!priv->regs) |
| return -ENOMEM; |
| |
| priv->input_clk = IOBUS_FREQ; |
| |
| /* deassert reset */ |
| writel(0x3, &priv->regs->brst); |
| |
| return 0; |
| } |
| |
| static int uniphier_i2c_remove(struct udevice *dev) |
| { |
| struct uniphier_i2c_dev *priv = dev_get_priv(dev); |
| |
| unmap_sysmem(priv->regs); |
| |
| return 0; |
| } |
| |
| static int send_and_recv_byte(struct uniphier_i2c_dev *dev, u32 dtrm) |
| { |
| writel(dtrm, &dev->regs->dtrm); |
| |
| /* |
| * This controller only provides interruption to inform the completion |
| * of each byte transfer. (No status register to poll it.) |
| * Unfortunately, U-Boot does not have a good support of interrupt. |
| * Wait for a while. |
| */ |
| udelay(dev->wait_us); |
| |
| return readl(&dev->regs->drec); |
| } |
| |
| static int send_byte(struct uniphier_i2c_dev *dev, u32 dtrm, bool *stop) |
| { |
| int ret = 0; |
| u32 drec; |
| |
| drec = send_and_recv_byte(dev, dtrm); |
| |
| if (drec & I2C_DREC_LAB) { |
| debug("uniphier_i2c: bus arbitration failed\n"); |
| *stop = false; |
| ret = -EREMOTEIO; |
| } |
| if (drec & I2C_DREC_LRB) { |
| debug("uniphier_i2c: slave did not return ACK\n"); |
| ret = -EREMOTEIO; |
| } |
| return ret; |
| } |
| |
| static int uniphier_i2c_transmit(struct uniphier_i2c_dev *dev, uint addr, |
| uint len, const u8 *buf, bool *stop) |
| { |
| int ret; |
| |
| debug("%s: addr = %x, len = %d\n", __func__, addr, len); |
| |
| ret = send_byte(dev, I2C_DTRM_STA | I2C_DTRM_NACK | addr << 1, stop); |
| if (ret < 0) |
| goto fail; |
| |
| while (len--) { |
| ret = send_byte(dev, I2C_DTRM_NACK | *buf++, stop); |
| if (ret < 0) |
| goto fail; |
| } |
| |
| fail: |
| if (*stop) |
| writel(I2C_DTRM_STO | I2C_DTRM_NACK, &dev->regs->dtrm); |
| |
| return ret; |
| } |
| |
| static int uniphier_i2c_receive(struct uniphier_i2c_dev *dev, uint addr, |
| uint len, u8 *buf, bool *stop) |
| { |
| int ret; |
| |
| debug("%s: addr = %x, len = %d\n", __func__, addr, len); |
| |
| ret = send_byte(dev, I2C_DTRM_STA | I2C_DTRM_NACK | |
| I2C_DTRM_RD | addr << 1, stop); |
| if (ret < 0) |
| goto fail; |
| |
| while (len--) |
| *buf++ = send_and_recv_byte(dev, len ? 0 : I2C_DTRM_NACK); |
| |
| fail: |
| if (*stop) |
| writel(I2C_DTRM_STO | I2C_DTRM_NACK, &dev->regs->dtrm); |
| |
| return ret; |
| } |
| |
| static int uniphier_i2c_xfer(struct udevice *bus, struct i2c_msg *msg, |
| int nmsgs) |
| { |
| int ret = 0; |
| struct uniphier_i2c_dev *dev = dev_get_priv(bus); |
| bool stop; |
| |
| for (; nmsgs > 0; nmsgs--, msg++) { |
| /* If next message is read, skip the stop condition */ |
| stop = nmsgs > 1 && msg[1].flags & I2C_M_RD ? false : true; |
| |
| if (msg->flags & I2C_M_RD) |
| ret = uniphier_i2c_receive(dev, msg->addr, msg->len, |
| msg->buf, &stop); |
| else |
| ret = uniphier_i2c_transmit(dev, msg->addr, msg->len, |
| msg->buf, &stop); |
| |
| if (ret < 0) |
| break; |
| } |
| |
| return ret; |
| } |
| |
| static int uniphier_i2c_set_bus_speed(struct udevice *bus, unsigned int speed) |
| { |
| struct uniphier_i2c_dev *priv = dev_get_priv(bus); |
| |
| /* max supported frequency is 400 kHz */ |
| if (speed > 400000) |
| return -EINVAL; |
| |
| /* bus reset: make sure the bus is idle when change the frequency */ |
| writel(0x1, &priv->regs->brst); |
| |
| writel((priv->input_clk / speed / 2 << 16) | (priv->input_clk / speed), |
| &priv->regs->clk); |
| |
| writel(0x3, &priv->regs->brst); |
| |
| /* |
| * Theoretically, each byte can be transferred in |
| * 1000000 * 9 / speed usec. For safety, wait more than double. |
| */ |
| priv->wait_us = 20000000 / speed; |
| |
| return 0; |
| } |
| |
| |
| static const struct dm_i2c_ops uniphier_i2c_ops = { |
| .xfer = uniphier_i2c_xfer, |
| .set_bus_speed = uniphier_i2c_set_bus_speed, |
| }; |
| |
| static const struct udevice_id uniphier_i2c_of_match[] = { |
| { .compatible = "socionext,uniphier-i2c" }, |
| { /* sentinel */ } |
| }; |
| |
| U_BOOT_DRIVER(uniphier_i2c) = { |
| .name = "uniphier-i2c", |
| .id = UCLASS_I2C, |
| .of_match = uniphier_i2c_of_match, |
| .probe = uniphier_i2c_probe, |
| .remove = uniphier_i2c_remove, |
| .priv_auto_alloc_size = sizeof(struct uniphier_i2c_dev), |
| .ops = &uniphier_i2c_ops, |
| }; |