include/configs/tao3530.h - platform/external/u-boot - Gitiles

 /*
  * Configuration settings for the TechNexion TAO-3530 SOM
  * equipped on Thunder baseboard.
  *
  * Edward Lin <linuxfae@technexion.com>
  * Tapani Utriainen <linuxfae@technexion.com>
  *
  * Copyright (C) 2013 Stefan Roese <sr@denx.de>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  */
 #define CONFIG_OMAP			/* in a TI OMAP core */

 #define CONFIG_OMAP_GPIO

 #define CONFIG_SDRC			/* Has an SDRC controller */

 #include <asm/arch/cpu.h>		/* get chip and board defs */
 #include <asm/arch/omap.h>

 /* Clock Defines */
 #define V_OSCK			26000000	/* Clock output from T2 */
 #define V_SCLK			(V_OSCK >> 1)

 #define CONFIG_MISC_INIT_R

 #define CONFIG_CMDLINE_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
 #define CONFIG_REVISION_TAG

 /*
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN		(4 << 20)
 #define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB sector */

 /*
  * Hardware drivers
  */

 /*
  * NS16550 Configuration
  */
 #define V_NS16550_CLK			48000000	/* 48MHz (APLL96/2) */

 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	(-4)
 #define CONFIG_SYS_NS16550_CLK		V_NS16550_CLK

 /*
  * select serial console configuration
  */
 #define CONFIG_CONS_INDEX		3
 #define CONFIG_SYS_NS16550_COM3		OMAP34XX_UART3

 /* allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE

 /* GPIO banks */
 #define CONFIG_OMAP3_GPIO_2		/* GPIO32 ..63  is in GPIO bank 2 */
 #define CONFIG_OMAP3_GPIO_3		/* GPIO64 ..95  is in GPIO bank 3 */
 #define CONFIG_OMAP3_GPIO_4		/* GPIO96 ..127 is in GPIO bank 4 */
 #define CONFIG_OMAP3_GPIO_5		/* GPIO128..159 is in GPIO bank 5 */
 #define CONFIG_OMAP3_GPIO_6		/* GPIO160..191 is in GPIO bank 6 */

 /* commands to include */
 #define CONFIG_CMD_MTDPARTS	/* Enable MTD parts commands */
 #define CONFIG_MTD_DEVICE	/* needed for mtdparts commands */
 #define MTDIDS_DEFAULT			"nand0=nand"
 #define MTDPARTS_DEFAULT		"mtdparts=nand:512k(x-loader),"\
 					"1920k(u-boot),128k(u-boot-env),"\
 					"4m(kernel),-(fs)"

 #define CONFIG_CMD_NAND		/* NAND support			*/

 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_OMAP34XX
 #define CONFIG_SYS_OMAP24_I2C_SPEED	100000
 #define CONFIG_SYS_OMAP24_I2C_SLAVE	1
 #define CONFIG_I2C_MULTI_BUS

 /*
  * TWL4030
  */
 #define CONFIG_TWL4030_POWER
 #define CONFIG_TWL4030_LED

 /*
  * Board NAND Info.
  */
 #define CONFIG_NAND_OMAP_GPMC
 #define CONFIG_SYS_NAND_ADDR		NAND_BASE	/* physical address */
 							/* to access nand */
 #define CONFIG_SYS_NAND_BASE		NAND_BASE	/* physical address */
 							/* to access nand at */
 							/* CS0 */

 #define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of NAND */
 							/* devices */
 #define CONFIG_SYS_NAND_BUSWIDTH_16BIT
 /* Environment information */

 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"loadaddr=0x82000000\0" \
 	"console=ttyO2,115200n8\0" \
 	"mpurate=600\0" \
 	"dvi_mode=omapfb.mode=dvi:1280x720-24@60\0" \
 	"tv_mode=omapfb.mode=tv:ntsc\0" \
 	"video_mode=omapdss.def_disp=lcd vram=6M omapfb.vram=0:2M,1:2M,2:2M\0" \
 	"lcd_mode=omapfb.mode=lcd:800x480@60 \0" \
 	"extra_options= \0" \
 	"mmcdev=0\0" \
 	"mmcroot=/dev/mmcblk0p2 rw\0" \
 	"mmcrootfstype=ext3 rootwait\0" \
 	"nandroot=ubi0:rootfs ubi.mtd=4\0" \
 	"nandrootfstype=ubifs\0" \
 	"mmcargs=setenv bootargs console=${console} " \
 		"mpurate=${mpurate} " \
 		"${video_mode} " \
 		"root=${mmcroot} " \
 		"rootfstype=${mmcrootfstype} " \
 		"${extra_options}\0" \
 	"nandargs=setenv bootargs console=${console} " \
 		"mpurate=${mpurate} " \
 		"${video_mode} " \
 		"${network_setting} " \
 		"root=${nandroot} " \
 		"rootfstype=${nandrootfstype} "\
 		"${extra_options}\0" \
 	"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
 	"bootscript=echo Running bootscript from mmc ...; " \
 		"source ${loadaddr}\0" \
 	"loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
 	"mmcboot=echo Booting from mmc ...; " \
 		"run mmcargs; " \
 		"bootm ${loadaddr}\0" \
 	"nandboot=echo Booting from nand ...; " \
 		"run nandargs; " \
 		"nand read ${loadaddr} 280000 400000; " \
 		"bootm ${loadaddr}\0" \

 #define CONFIG_BOOTCOMMAND \
 	"if mmc rescan ${mmcdev}; then " \
 		"if run loadbootscript; then " \
 			"run bootscript; " \
 		"else " \
 			"if run loaduimage; then " \
 				"run mmcboot; " \
 			"else run nandboot; " \
 			"fi; " \
 		"fi; " \
 	"else run nandboot; fi"

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */

 /* turn on command-line edit/hist/auto */
 #define CONFIG_CMDLINE_EDITING
 #define CONFIG_COMMAND_HISTORY
 #define CONFIG_AUTO_COMPLETE

 /* Print Buffer Size */
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS		16	/* max number of command args */
 /* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)

 #define CONFIG_SYS_ALT_MEMTEST		1
 #define CONFIG_SYS_MEMTEST_START	(0x82000000)		/* memtest */
 								/* defaults */
 #define CONFIG_SYS_MEMTEST_END		(0x83FFFFFF)		/* 64MB */
 #define CONFIG_SYS_MEMTEST_SCRATCH	(0x81000000)	/* dummy address */

 #define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0)	/* default */
 							/* load address */
 #define CONFIG_SYS_TEXT_BASE		0x80008000

 /*
  * OMAP3 has 12 GP timers, they can be driven by the system clock
  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
  * This rate is divided by a local divisor.
  */
 #define CONFIG_SYS_TIMERBASE		(OMAP34XX_GPT2)
 #define CONFIG_SYS_PTV			2       /* Divisor: 2^(PTV+1) => 8 */

 /*
  * Stack sizes
  *
  * The stack sizes are set up in start.S using the settings below
  */
 #define CONFIG_STACKSIZE	(128 << 10)	/* regular stack 128 KiB */

 /*
  * Physical Memory Map
  */
 #define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
 #define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
 #define PHYS_SDRAM_1_SIZE	(32 << 20)	/* at least 32 MiB */
 #define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1

 /*
  * FLASH and environment organization
  */

 /* **** PISMO SUPPORT *** */
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
 #define CONFIG_SYS_FLASH_BASE		NAND_BASE

 /* Monitor at start of flash */
 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_ONENAND_BASE		ONENAND_MAP

 #define CONFIG_ENV_IS_IN_NAND		1
 #define ONENAND_ENV_OFFSET		0x260000 /* environment starts here */
 #define SMNAND_ENV_OFFSET		0x260000 /* environment starts here */

 #define CONFIG_SYS_ENV_SECT_SIZE	(128 << 10)
 #define CONFIG_ENV_OFFSET		SMNAND_ENV_OFFSET
 #define CONFIG_ENV_ADDR			CONFIG_ENV_OFFSET

 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
 #define CONFIG_SYS_INIT_RAM_ADDR	0x4020f800
 #define CONFIG_SYS_INIT_RAM_SIZE	0x800
 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
 					 CONFIG_SYS_INIT_RAM_SIZE - \
 					 GENERATED_GBL_DATA_SIZE)

 #define CONFIG_OMAP3_SPI

 /*
  * USB
  *
  * Currently only EHCI is enabled, the MUSB OTG controller
  * is not enabled.
  */

 /* USB EHCI */
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_OMAP
 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO	162

 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
 #define CONFIG_USB_HOST_ETHER
 #define CONFIG_USB_ETHER_SMSC95XX

 #define CONFIG_USB_ETHER
 #define CONFIG_USB_ETHER_RNDIS

 /* Defines for SPL */
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_NAND_SIMPLE

 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME	"u-boot.img"

 #define CONFIG_SPL_BOARD_INIT
 #define CONFIG_SPL_NAND_BASE
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_ECC
 #define CONFIG_SPL_OMAP3_ID_NAND
 #define CONFIG_SPL_LDSCRIPT		"arch/arm/mach-omap2/u-boot-spl.lds"

 /* NAND boot config */
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_PAGE_COUNT	64
 #define CONFIG_SYS_NAND_PAGE_SIZE	2048
 #define CONFIG_SYS_NAND_OOBSIZE		64
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
 #define CONFIG_SYS_NAND_BAD_BLOCK_POS	NAND_LARGE_BADBLOCK_POS
 /*
  * Use the ECC/OOB layout from omap_gpmc.h that matches your chip:
  * SP vs LP, 8bit vs 16bit: GPMC_NAND_HW_ECC_LAYOUT
  */
 #define CONFIG_SYS_NAND_ECCPOS		{ 2, 3, 4, 5, 6, 7, 8, 9, \
 					 10, 11, 12, 13 }
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	3
 #define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_HW

 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000

 #define CONFIG_SPL_TEXT_BASE		0x40200800
 #define CONFIG_SPL_MAX_SIZE		(SRAM_SCRATCH_SPACE_ADDR - \
 					 CONFIG_SPL_TEXT_BASE)

 /*
  * Use 0x80008000 as TEXT_BASE here for compatibility reasons with the
  * older x-loader implementations. And move the BSS area so that it
  * doesn't overlap with TEXT_BASE.
  */
 #define CONFIG_SYS_TEXT_BASE		0x80008000
 #define CONFIG_SPL_BSS_START_ADDR	0x80100000
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000		/* 512 KB */

 #define CONFIG_SYS_SPL_MALLOC_START	0x80208000
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000

 #endif /* __CONFIG_H */
	/*
	* Configuration settings for the TechNexion TAO-3530 SOM
	* equipped on Thunder baseboard.
	*
	* Edward Lin <linuxfae@technexion.com>
	* Tapani Utriainen <linuxfae@technexion.com>
	*
	* Copyright (C) 2013 Stefan Roese <sr@denx.de>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	*/
	#define CONFIG_OMAP /* in a TI OMAP core */

	#define CONFIG_OMAP_GPIO

	#define CONFIG_SDRC /* Has an SDRC controller */

	#include <asm/arch/cpu.h> /* get chip and board defs */
	#include <asm/arch/omap.h>

	/* Clock Defines */
	#define V_OSCK 26000000 /* Clock output from T2 */
	#define V_SCLK (V_OSCK >> 1)

	#define CONFIG_MISC_INIT_R

	#define CONFIG_CMDLINE_TAG
	#define CONFIG_SETUP_MEMORY_TAGS
	#define CONFIG_INITRD_TAG
	#define CONFIG_REVISION_TAG

	/*
	* Size of malloc() pool
	*/
	#define CONFIG_SYS_MALLOC_LEN (4 << 20)
	#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */

	/*
	* Hardware drivers
	*/

	/*
	* NS16550 Configuration
	*/
	#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */

	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE (-4)
	#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK

	/*
	* select serial console configuration
	*/
	#define CONFIG_CONS_INDEX 3
	#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3

	/* allow to overwrite serial and ethaddr */
	#define CONFIG_ENV_OVERWRITE

	/* GPIO banks */
	#define CONFIG_OMAP3_GPIO_2 /* GPIO32 ..63 is in GPIO bank 2 */
	#define CONFIG_OMAP3_GPIO_3 /* GPIO64 ..95 is in GPIO bank 3 */
	#define CONFIG_OMAP3_GPIO_4 /* GPIO96 ..127 is in GPIO bank 4 */
	#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */
	#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */

	/* commands to include */
	#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
	#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
	#define MTDIDS_DEFAULT "nand0=nand"
	#define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\
	"1920k(u-boot),128k(u-boot-env),"\
	"4m(kernel),-(fs)"

	#define CONFIG_CMD_NAND /* NAND support */

	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_OMAP34XX
	#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
	#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
	#define CONFIG_I2C_MULTI_BUS

	/*
	* TWL4030
	*/
	#define CONFIG_TWL4030_POWER
	#define CONFIG_TWL4030_LED

	/*
	* Board NAND Info.
	*/
	#define CONFIG_NAND_OMAP_GPMC
	#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
	/* to access nand */
	#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
	/* to access nand at */
	/* CS0 */

	#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
	/* devices */
	#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
	/* Environment information */

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"loadaddr=0x82000000\0" \
	"console=ttyO2,115200n8\0" \
	"mpurate=600\0" \
	"dvi_mode=omapfb.mode=dvi:1280x720-24@60\0" \
	"tv_mode=omapfb.mode=tv:ntsc\0" \
	"video_mode=omapdss.def_disp=lcd vram=6M omapfb.vram=0:2M,1:2M,2:2M\0" \
	"lcd_mode=omapfb.mode=lcd:800x480@60 \0" \
	"extra_options= \0" \
	"mmcdev=0\0" \
	"mmcroot=/dev/mmcblk0p2 rw\0" \
	"mmcrootfstype=ext3 rootwait\0" \
	"nandroot=ubi0:rootfs ubi.mtd=4\0" \
	"nandrootfstype=ubifs\0" \
	"mmcargs=setenv bootargs console=${console} " \
	"mpurate=${mpurate} " \
	"${video_mode} " \
	"root=${mmcroot} " \
	"rootfstype=${mmcrootfstype} " \
	"${extra_options}\0" \
	"nandargs=setenv bootargs console=${console} " \
	"mpurate=${mpurate} " \
	"${video_mode} " \
	"${network_setting} " \
	"root=${nandroot} " \
	"rootfstype=${nandrootfstype} "\
	"${extra_options}\0" \
	"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
	"source ${loadaddr}\0" \
	"loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
	"mmcboot=echo Booting from mmc ...; " \
	"run mmcargs; " \
	"bootm ${loadaddr}\0" \
	"nandboot=echo Booting from nand ...; " \
	"run nandargs; " \
	"nand read ${loadaddr} 280000 400000; " \
	"bootm ${loadaddr}\0" \

	#define CONFIG_BOOTCOMMAND \
	"if mmc rescan ${mmcdev}; then " \
	"if run loadbootscript; then " \
	"run bootscript; " \
	"else " \
	"if run loaduimage; then " \
	"run mmcboot; " \
	"else run nandboot; " \
	"fi; " \
	"fi; " \
	"else run nandboot; fi"

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */

	/* turn on command-line edit/hist/auto */
	#define CONFIG_CMDLINE_EDITING
	#define CONFIG_COMMAND_HISTORY
	#define CONFIG_AUTO_COMPLETE

	/* Print Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
	sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	/* Boot Argument Buffer Size */
	#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)

	#define CONFIG_SYS_ALT_MEMTEST 1
	#define CONFIG_SYS_MEMTEST_START (0x82000000) /* memtest */
	/* defaults */
	#define CONFIG_SYS_MEMTEST_END (0x83FFFFFF) /* 64MB */
	#define CONFIG_SYS_MEMTEST_SCRATCH (0x81000000) /* dummy address */

	#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */
	/* load address */
	#define CONFIG_SYS_TEXT_BASE 0x80008000

	/*
	* OMAP3 has 12 GP timers, they can be driven by the system clock
	* (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
	* This rate is divided by a local divisor.
	*/
	#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
	#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */

	/*
	* Stack sizes
	*
	* The stack sizes are set up in start.S using the settings below
	*/
	#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */

	/*
	* Physical Memory Map
	*/
	#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
	#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
	#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
	#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1

	/*
	* FLASH and environment organization
	*/

	/* ** PISMO SUPPORT * */
	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
	#define CONFIG_SYS_FLASH_BASE NAND_BASE

	/* Monitor at start of flash */
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP

	#define CONFIG_ENV_IS_IN_NAND 1
	#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
	#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */

	#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10)
	#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
	#define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET

	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
	#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
	#define CONFIG_SYS_INIT_RAM_SIZE 0x800
	#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
	CONFIG_SYS_INIT_RAM_SIZE - \
	GENERATED_GBL_DATA_SIZE)

	#define CONFIG_OMAP3_SPI

	/*
	* USB
	*
	* Currently only EHCI is enabled, the MUSB OTG controller
	* is not enabled.
	*/

	/* USB EHCI */
	#define CONFIG_USB_EHCI
	#define CONFIG_USB_EHCI_OMAP
	#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 162

	#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
	#define CONFIG_USB_HOST_ETHER
	#define CONFIG_USB_ETHER_SMSC95XX

	#define CONFIG_USB_ETHER
	#define CONFIG_USB_ETHER_RNDIS

	/* Defines for SPL */
	#define CONFIG_SPL_FRAMEWORK
	#define CONFIG_SPL_NAND_SIMPLE

	#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
	#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"

	#define CONFIG_SPL_BOARD_INIT
	#define CONFIG_SPL_NAND_BASE
	#define CONFIG_SPL_NAND_DRIVERS
	#define CONFIG_SPL_NAND_ECC
	#define CONFIG_SPL_OMAP3_ID_NAND
	#define CONFIG_SPL_LDSCRIPT "arch/arm/mach-omap2/u-boot-spl.lds"

	/* NAND boot config */
	#define CONFIG_SYS_NAND_5_ADDR_CYCLE
	#define CONFIG_SYS_NAND_PAGE_COUNT 64
	#define CONFIG_SYS_NAND_PAGE_SIZE 2048
	#define CONFIG_SYS_NAND_OOBSIZE 64
	#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
	#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
	/*
	* Use the ECC/OOB layout from omap_gpmc.h that matches your chip:
	* SP vs LP, 8bit vs 16bit: GPMC_NAND_HW_ECC_LAYOUT
	*/
	#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
	10, 11, 12, 13 }
	#define CONFIG_SYS_NAND_ECCSIZE 512
	#define CONFIG_SYS_NAND_ECCBYTES 3
	#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW

	#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000

	#define CONFIG_SPL_TEXT_BASE 0x40200800
	#define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \
	CONFIG_SPL_TEXT_BASE)

	/*
	* Use 0x80008000 as TEXT_BASE here for compatibility reasons with the
	* older x-loader implementations. And move the BSS area so that it
	* doesn't overlap with TEXT_BASE.
	*/
	#define CONFIG_SYS_TEXT_BASE 0x80008000
	#define CONFIG_SPL_BSS_START_ADDR 0x80100000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */

	#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000

	#endif /* __CONFIG_H */